Partners save 15% on every standard

Valid

GB/T 38243-2019Rubber - Calibration and verification of hardness testers (English PDF)

Also coversGBT38243-2019

Open the GB/T 38243-2019 preview as PDF

Preview — first pages of GB/T 38243-2019

This is a limited preview

Buy now to download the full PDF

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

October 18, 2019

Implementation date

May 1, 2020

Scope

GB/T 38243-2019 (Rubber - Calibration and verification of hardness testers) is available as an English-translated PDF.

GB/T 38243-2019 — This standard specifies Type A, Type D, AO and AM Shore Hardness Testers (see ISO 7619-1), Portable Rubber International Hardness Tester (see ISO 7619-2), rubber international hardness tester (see ISO 48) and ultra-soft rubber hardness tester (see ISO 27588) technical requirements for inspection and calibration Summation method.

Document preview — GB/T 38243-2019

National Standard of the People's Republic of China

ICS: 19.060; 83.060
Classification: N 72

Issued by: State Administration for Market Regulation, China National Standardization Administration

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Technical requirements for inspection and calibration
4.1 Environmental conditions

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009.

This standard uses the translation method equivalent to ISO 18898.2016 "Test and Calibration of Rubber Hardness Tester".

The documents of our country that have a consistent correspondence with the international documents referenced in this standard are as follows.

Rubber and rubber -- Determination of hardness of indented rubber -- Part 1 . Shore hardness test method

(Shaoer hardness) (ISO 7619-1.2004, IDT)

Rubber and rubber -- Determination of hardness of indented rubber -- Part 2 . Portable rubber country

Hardness test method (ISO 7619-2.2004, IDT)

---GB/T 6031-2017 Determination of hardness of vulcanized rubber or thermoplastic rubber (10IRHD~100IRHD) (ISO 48.

2010, IDT)

---GB/T 25269-2010 Rubber Test Equipment Calibration Guide (ISO 18899.2004, IDT)

---GB/T 27025-2008 General requirements for testing and calibration laboratory capabilities (ISO /IEC 17025.2005, IDT)

1 Scope

This standard specifies Type A, Type D, AO and AM Shore Hardness Testers (see ISO 7619-1), Portable Rubber International Hardness Tester

(see ISO 7619-2), rubber international hardness tester (see ISO 48) and ultra-soft rubber hardness tester (see ISO 27588) technical requirements for inspection and calibration

Summation method.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article.

Pieces. For undated references, the latest edition (including all amendments) applies to this document.

ISO 48 vulcanized rubber or thermoplastic rubber hardness (10IRHD~100IRHD) [Rubber, vulcanizedor

thermoplastic-Determinationofhardness(hardnessbetween10IRHDand100IRHD)]

Vulcanized rubber or thermoplastic rubbers - Test method for hardness - Part 1 . Shore hardness test method (Shore hardness)

[Rubber, vulcanizedorthermoplastic-Determinationofindentationhardness-Part 1. Durometer

Method(Shorehardness)]

Vulcanized rubber or thermoplastic rubbers - Determination of hardness - Part 2. Portable rubber international hardness test method

(Rubber, vulcanizedorthermoplastic-Determinationofindentationhardness-Part 2. IRHDpocket

Metermethod)

ISO 18899 Rubber Test Equipment Calibration Guide (Rubber-Guidetothecalibrationoftestequipment)

ISO 27588 vulcanized rubber and thermoplastic rubber with static softness tester using a soft rubber hardness tester [Rubber, vulcanizedor

thermoplastic-Determinationofdead-loadhardnessusingtheverylowrubberhardness(VLRH)

Scale]

General requirements for ISO /IEC 17025 testing and calibration laboratory capabilities (Generalrequirementsforthecompetenceof

Testingandcalibrationlaboratorie)

3 Terms and definitions

The terms and definitions defined by ISO 48 and ISO 18899 apply to this document.

4 Technical requirements for inspection and calibration

4.1 Environmental conditions

The room temperature should be within the range of 18 ° C ~ 25 ° C for inspection and calibration.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — all pages — is available in the English PDF.

Referenced standards

Normative references

ISO 48 · ISO 18899 · ISO 27588 · IEC 17025

How to Buy GB/T 38243-2019

1Add to cart. Click the "Buy GB/T 38243-2019" button on this page. You can add more standards before checkout.
2Checkout. Enter your email and billing details. Payment is processed securely by Stripe (cards, Apple Pay, Google Pay supported).
3Instant delivery (0–9 sec). Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4Invoice included. A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.