Valid

GB/T 38240-2019Non-destructive testing instruments—Standard practice for manufacturing characterization of digital detector arrays (English PDF)

无损检测仪器 射线数字探测器阵列制造特征

Preview PDF

This is a limited preview

Buy now to download the full PDF (24 pages)

Need quotation for your management?

Get a formal quotation for GB/T 38240-2019 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

October 18, 2019

Implementation date

May 1, 2020

Scope

GB/T 38240-2019 is the English-translated version of 无损检测仪器 射线数字探测器阵列制造特征.

GB/T 38240-2019 is the Chinese standard "Non-destructive testing instruments—Standard practice for manufacturing characterization of digital detector arrays".

Its scope clause reads: This standard specifies the instruments and devices of the ray digital detector, calibration comparison and standard operation, detection methods, calculation and analysis of results, etc. content.

This standard applies to digital area array detectors. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 38240-2019

National Standard of the People's Republic of China

ICS
19.100
Classification
N 78

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Terms and Definitions
  • 4 Meaning and use
  • 5 Instruments and Devices
  • 6 Calibration comparison and standard operation
  • 7 Method
  • 8 Results calculation or analysis
  • 9 Display of manufacturer test results
  • 10 Classification of Digital Detector Arrays
  • 11 Accuracy and deviation
  • 12 Keywords
  • Appendix A (Normative) Input and Output Data Templates

1 Scope

This standard specifies the instruments and devices of the ray digital detector, calibration comparison and standard operation, detection methods, calculation and analysis of results, etc.

content.

This standard applies to digital area array detectors.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article.

Pieces. For undated references, the latest edition (including all amendments) applies to this document.

ASTME1742 Radiographic Inspection Procedure (Standardpracticeforradiographicexamination)

ASTME1815 Standard Test Method for Industrial Radiation Photographic Film System (Standardtestmethodforclassifi-

Cationoffilmsystemsforindustrialradiography)

ASTME2002 Standard Practice for Determining Total Image Unsharpness in Radiology (Standardpracticefordetermining

Totalimageunsharpnessandbasicspatialresolutioninradiographyandradioscopy)

ASTME2446 calculates the long-term stability of a radiographic system (Standardpracticeforufacturingcharacter-

Izationofcomputedradiographysystems)

3 Terms and definitions

The following terms and definitions apply to this document.

3.1 Digital detector array system digitaldetecterarray (DDA) system

A discrete array of electronic devices that convert ionizing radiation or penetrating radiation into analog signals. Then pass these digitized analog signals

It is input to a computer and displayed in the form of a digital image of the radiant energy spectrum corresponding to the input area of the computer-driven method.

Note. The first step in the conversion of ionizing radiation or penetrating radiation into an electronic signal is to convert it into visible light by using scintillation material ionizing radiation or penetrating radiation. This

The speed range of these devices, generating an image from a few seconds until several images are generated in one second, reaching or exceeding the speed of real-time fluoroscopy (usually 30 frames/s).

3.2 Signal-to-noise ratio signal-to-noiseratio; SNR

The ratio of the average of the signal strength to the standard deviation of the noise intensity depends on the radiation dose and the performance of the digital detector array system.

3.3 Contrast-noise ratio contrast-to-noiseratio; CNR

The ratio of the average signal level difference between the two image regions to the standard deviation of the signal level.

Note. In the application here, the above two image areas are step wedge grooves and substrate. The standard deviation of substrate strength is a measure of noise.

The CNR depends on the radiation dose and the performance of the digital detector array system.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 24 pages — is available in the English PDF.

Similar standards

How to Download GB/T 38240-2019

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
24 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 38240-2019

$415.00