GB/T 38168-2019Vitreous and porcelain enamel finishes - Guide to selection of test methods for vitreous and porcelain enamelled areas of articles (English PDF)
搪瓷制品和瓷釉 涂搪制品瓷层的试验方法选择指南
This is a limited preview
Buy now to download the full PDF (21 pages)
Need quotation for your management?
Get a formal quotation for GB/T 38168-2019 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
October 18, 2019
Implementation date
May 1, 2020
Scope
GB/T 38168-2019 is the English-translated version of 搪瓷制品和瓷釉 涂搪制品瓷层的试验方法选择指南.
GB/T 38168-2019 is the Chinese national standard on vitreous and porcelain enamel finishes, and it is a guide to selecting the test methods for the vitreous and porcelain enamelled areas of articles.
It is a selection guide for the test methods used to assess the performance of enamel and enamelled articles for different applications: the test methods it refers to can be used to measure the properties of those articles and to relate those properties to particular requirements for enamelled articles.
It notes that most of the test methods described in the ISO and European standards are limited and give neither acceptance criteria nor performance ranges. It applies to enamelled articles on metal substrates of every kind.
Clause 2 lists the surface characteristics of enamel and the corresponding test methods in Table 1, which identifies the performance tests and the matching test methods for thirty kinds of enamelled article, and fixes the symbols used in that table for a test method that is applicable, for one that may need correction where the article has special requirements, and for one that does not apply.
It modifies ISO 4528:2015 by the redrafting method. It was issued on 18 October 2019 and has applied since 1 May 2020.
Found what you need?
Document preview — GB/T 38168-2019
National Standard of the People's Republic of China
- ICS
- 25.220.50
- Classification
- Y 26
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- 1 Scope
- 2 Select test method
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
This standard uses the redrafting method to modify the test method for the porcelain layer of enamel products and enamel coated products using ISO 4528:2015. Guide to the guide. This standard has made the following editorial changes.
--- For some of the ISO standards and EN standards quoted in Table 1, replaced by the applicable Chinese standards;
--- Removed footnote e from ISO 4528:2015 Table 1, footnote e for ISO 4528:2015 for the EU market.
Caution - If you do not take adequate safety measures, this standard may not comply with our health and safety regulations, and the required use Substances and procedures can harm your health. This standard does not address any health hazards, safety or environmental issues and regulations related to this standard.
Users of this standard are responsible for developing health, safety and environmentally acceptable measures and complying with national and international regulations. comply with This standard cannot be used as a legal basis for exemption.
1 Scope
This standard is a selection guide for testing methods for evaluating the performance of enamel and enamel for different applications. The test method it references can be used The properties of these articles are measured and these properties are associated with specific enamel article requirements.
Most of the test methods described in ISO International Standards and European Standards are limited and do not provide performance acceptance criteria or Performance range.
This standard applies to enamel products of various metal substrates.
2 Select test method
The surface characteristics and test methods of enamel are listed in Table 1. Table 1 identifies the performance tests and corresponding test methods for 30 enamel products. The following symbols are used in Table 1.
--- The test method given is applicable;
( )---For enamel products with special requirements, the test methods given may need to be corrected;
- --- The test method given does not apply.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 21 pages — is available in the English PDF.
How to Download GB/T 38168-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 38168-2019
$205.00