GB/T 38092-2019Vitreous and porcelain enamels - Determination of fluidity behaviour - Fusion flow test (English PDF)
搪瓷制品和瓷釉 流动性的测试 熔流试验
This is a limited preview
Buy now to download the full PDF (17 pages)
Need quotation for your management?
Get a formal quotation for GB/T 38092-2019 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
October 18, 2019
Implementation date
May 1, 2020
Scope
GB/T 38092-2019 is the English-translated version of 搪瓷制品和瓷釉 流动性的测试 熔流试验.
GB/T 38092-2019 — This standard specifies a method for testing the enamel fluidity of enamel during firing. This method is a relative method of fluidity testing (Comparative method), not an absolute method.
Found what you need?
Document preview — GB/T 38092-2019
National Standard of the People's Republic of China
- ICS
- 25.220.50
- Classification
- Y 26
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- 1 Scope
- 2 Principle
- 3 Materials and equipment
- 3.2 Ball mill.
- 3.3 Drying equipment. such as oven, electric hot plate or sand bath.
- 3.4 Research and development.
- 3.5 捣 hammer.
- 3.6 Balance. The accuracy is 0.01g.
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
This standard uses the translation method equivalent to ISO 4534.2010 "Test Melt Flow Test for Enamel Products and Enamel Fluidity".
This standard is proposed and managed by the China Light Industry Association.
This standard was drafted. Donghua University, National Eyeglass Glass Enamel Product Quality Supervision and Inspection Center, Shanghai Glasses Glass Enamel Products
Quality supervision and inspection station.
1 Scope
This standard specifies a method for testing the enamel fluidity of enamel during firing. This method is a relative method of fluidity testing
(Comparative method), not an absolute method.
2 Principle
According to the conditions of sample preparation, it can be divided into dry preparation or wet preparation. Cylindrical sample with a certain weight can be made of enamel powder, dry
The dried glaze or the reference sample agreed by both parties is pressed.
The sample was placed on an unglazed ceramic plate in a horizontal position in an electric furnace and melted to a hemispherical shape at a predetermined temperature. Then, tilt
An glazed ceramic plate to allow molten enamel to flow at a certain angle for a predetermined period of time.
The flow length coefficient F1 and the flow width coefficient Fb are calculated based on the flow length and flow width of the sample.
3 Materials and equipment
3.1 Reference sample. It is agreed by both parties to the contract that it has similar melt flow properties to the tested enamel.
3.2 Ball mill.
3.3 Drying equipment. such as oven, electric hot plate or sand bath.
3.4 Research and development.
3.5 捣 hammer.
3.6 Balance. The accuracy is 0.01g.
3.7 Press. It can produce a pressure of at least 5N/mm2 with a cylindrical mold with an inner diameter of 8mm~10mm. Every experiment,
A mold of the same specification should be used.
3.8 Flow plate. It consists of a smooth, uniform, non-glazed ceramic plate made of at least 1100 ° C. It has a side length of about 75 mm and a thickness of
5mm~6mm, the water absorption rate is <=25% under atmospheric pressure. It can also be cut from a larger ceramic plate (see A.1).
3.9 Tilting frame. It is used to place the flow board horizontally in the experimental electric furnace. The inclination angle of the board is between 30° and 90°, as shown in Figure 1 and Figure 2.
Note. For specimens with very high viscosity, increase the angle of inclination.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.
How to Download GB/T 38092-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 38092-2019
$145.00