Valid

GB/T 37854-2019Wide-mouth glass containers - Deviation from flatness of top sealing surface - Test methods (English PDF)

广口玻璃容器 封合面平面度偏差 试验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (11 pages)

Need quotation for your management?

Get a formal quotation for GB/T 37854-2019 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

August 30, 2019

Implementation date

March 1, 2020

Scope

GB/T 37854-2019 is the English-translated version of 广口玻璃容器 封合面平面度偏差 试验方法.

GB/T 37854-2019 — This standard specifies two complementary test methods for determining the flatness deviation of the sealing surface of a wide-mouth glass container.

This standard applies to wide-mouth glass containers that require sterilization and sealing.

Found what you need?

Document preview — GB/T 37854-2019

National Standard of the People's Republic of China

ICS
81.040.30
Classification
Y 22

Issued by: State Administration for Market Regulation, China National Standardization Administration

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Principle
  • 5 instruments
  • 5.1 Level the bottom plate.
  • 5.2 Thickness gauge. The step is 0.05 mm, ie. 0.05 mm, 0.1 mm, and the like.
  • 6 sampling
  • 1 Scope 1
  • 2 Normative references 1
  • 3 Terms and Definitions 1
  • 4 Principle 1
  • 5 Instrument 1
  • 6 sampling 1
  • 7 Test step 2
  • 8 results indicate 2
  • 9 Inspection report 2
  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Principle
  • 5 instruments
  • 5.1 Level the bottom plate.
  • 5.2 Thickness gauge. The step is 0.05 mm, ie. 0.05 mm, 0.1 mm, and the like.
  • 6 sampling

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009.

This standard uses the translation method equivalent to ISO 9885.1991 "flat mouth glass container sealing surface flatness deviation test method".

The documents of our country that have a consistent correspondence with the international documents referenced in this standard are as follows.

---GB/T 9987-2011 Glass bottle manufacturing terminology (ISO 7348.1991, MOD).

This standard was proposed by the China Light Industry Association.

This standard is under the jurisdiction of the National Daily Glass Standardization Technical Committee (SAC/TC377).

This standard was drafted. Donghua University, National Eyeglass Glass Enamel Product Quality Supervision and Inspection Center, National Daily Glass Enamel Standardization

center.

1 Scope

This standard specifies two complementary test methods for determining the flatness deviation of the sealing surface of a wide-mouth glass container.

This standard applies to wide-mouth glass containers that require sterilization and sealing.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest edition (including all amendments) applies to this document.

ISO 7348.1991 Glass Container Manufacturing Terminology (Glasscontains-Manufacture-Vocabulary)

3 Terms and definitions

The following terms and definitions defined by ISO 7348 apply to this document.

3.1

Fitting surface flatness deviation deviationfromflatnessoftopsealingsurface

The amount of saddle deformation of the mouth sealing ring of the container.

Note 1. The saddle-like deformation of the mouth sealing ring usually occurs after forming and before leaving the annealing furnace.

Note 2. The flatness deviation of the sealing surface here is different from ISO 9009.1991 "The height and the non-parallelism test of the glass container based on the bottom of the container.

The method refers to "the degree of non-parallelism of the mouth based on the bottom of the container".

4 Principle

4.1 Quick test to determine if the sealing surface meets the predetermined flatness requirements.

4.2 Measure the distance between the sealing surface and the plate pressed under the sealing surface.

5 instruments

5.1 Level the bottom plate.

5.2 Thickness gauge. The step is 0.05 mm, ie. 0.05 mm, 0.1 mm, and the like.

Note. For fast detection, especially automatic detection, other instruments can also be used, such as placing the container under test on the standard rubber base of the instrument, and the measurement has been pumped.

The vacuum of the empty container is converted to a flatness deviation expressed in millimeters (mm).

6 sampling

The test should be carried out in a predetermined number of samples. The sample shall meet the test requirements.

GB/T 37854-2019

(Wide-mouth glass container, flatness deviation of sealing surface)

ICS 81.040.30

Y22

National Standards of People's Republic of China

Wide mouth glass container

Sealing surface flatness deviation test method

Wide-mouthglasscontainers-

Deviationfromflatnessoftopsealingsurface-Testmethods

(ISO 9885.1991, IDT)

Published on.2019-08-30

2020-03-01 implementation

State market supervision and administration

China National Standardization Administration issued

Content

Foreword I

1 Scope 1

2 Normative references 1

3 Terms and Definitions 1

4 Principle 1

5 Instrument 1

6 sampling 1

7 Test step 2

8 results indicate 2

9 Inspection report 2

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009.

This standard uses the translation method equivalent to ISO 9885.1991 "flat mouth glass container sealing surface flatness deviation test method".

The documents of our country that have a consistent correspondence with the international documents referenced in this standard are as follows.

---GB/T 9987-2011 Glass bottle manufacturing terminology (ISO 7348.1991, MOD).

This standard was proposed by the China Light Industry Association.

This standard is under the jurisdiction of the National Daily Glass Standardization Technical Committee (SAC/TC377).

This standard was drafted. Donghua University, National Eyeglass Glass Enamel Product Quality Supervision and Inspection Center, National Daily Glass Enamel Standardization

center.

1 Scope

This standard specifies two complementary test methods for determining the flatness deviation of the sealing surface of a wide-mouth glass container.

This standard applies to wide-mouth glass containers that require sterilization and sealing.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest edition (including all amendments) applies to this document.

ISO 7348.1991 Glass Container Manufacturing Terminology (Glasscontains-Manufacture-Vocabulary)

3 Terms and definitions

The following terms and definitions defined by ISO 7348 apply to this document.

3.1

Fitting surface flatness deviation deviationfromflatnessoftopsealingsurface

The amount of saddle deformation of the mouth sealing ring of the container.

Note 1. The saddle-like deformation of the mouth sealing ring usually occurs after forming and before leaving the annealing furnace.

Note 2. The flatness deviation of the sealing surface here is different from ISO 9009.1991 "The height and the non-parallelism test of the glass container based on the bottom of the container.

The method refers to "the degree of non-parallelism of the mouth based on the bottom of the container".

4 Principle

4.1 Quick test to determine if the sealing surface meets the predetermined flatness requirements.

4.2 Measure the distance between the sealing surface and the plate pressed under the sealing surface.

5 instruments

5.1 Level the bottom plate.

5.2 Thickness gauge. The step is 0.05 mm, ie. 0.05 mm, 0.1 mm, and the like.

Note. For fast detection, especially automatic detection, other instruments can also be used, such as placing the container under test on the standard rubber base of the instrument, and the measurement has been pumped.

The vacuum of the empty container is converted to a flatness deviation expressed in millimeters (mm).

6 sampling

The test should be carried out in a predetermined number of samples. The sample shall meet the test requirements.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 11 pages — is available in the English PDF.

Referenced standards

Normative references

ISO 7348.1991

How to Download GB/T 37854-2019

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
11 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 37854-2019

$90.00