Valid

GB/T 37493-2019Inspection of grain and oils - Determination of soluble sugar in cereals and pules seeds - Shaffer-Somogyi (English PDF)

粮油检验 谷物、豆类中可溶性糖的测定 铜还原-碘量法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 37493-2019 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

May 10, 2019

Implementation date

December 1, 2019

Scope

GB/T 37493-2019 is the English-translated version of 粮油检验 谷物、豆类中可溶性糖的测定 铜还原-碘量法.

GB/T 37493-2019 is the Chinese standard "Inspection of grain and oils - Determination of soluble sugar in cereals and pules seeds - Shaffer-Somogyi".

Its scope clause reads: This standard specifies the principle of copper reduction-iodine content determination method for soluble sugar in grains and beans, reagents, instruments and equipment, sample preparation, Sample measurement, result calculation and precision.

This standard applies to the determination of soluble sugar in grains and legumes. The quantitative range of this standard method is 0mg ~ 2.5mg reducing sugar.

Its clauses include principle; reagent; instruments and equipment; analysis steps; results calculation; precision.

Found what you need?

Document preview — GB/T 37493-2019

National Standard of the People's Republic of China

ICS
67.060
Classification
C 53

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 Normative references
  • 3 Principle
  • 4 Reagent
  • 5 Instruments and equipment
  • 6 Analysis steps
  • 7 Results calculation
  • 8 Precision

1 Scope

This standard specifies the principle of copper reduction-iodine content determination method for soluble sugar in grains and beans, reagents, instruments and equipment, sample preparation,

Sample measurement, result calculation and precision.

This standard applies to the determination of soluble sugar in grains and legumes.

The quantitative range of this standard method is 0mg ~ 2.5mg reducing sugar.

2 Normative references

The following documents are essential for the application of this document. For dated references, only the dated version applies to this article

Pieces. For undated references, the latest version (including all amendments) applies to this document.

Preparation of GB/T 601 chemical reagent standard titration solution

GB/T 5490 General Rules for Inspection of Grain and Oil

GB/T 6682 Analytical laboratory water specifications and test methods

3 Principle

Soluble sugars in grains and beans are hydrolyzed to reducing sugars and interact with Cu2 in alkaline copper reagents to form cuprous oxide (Cu2O) precipitates.

Lake. Under the acidic conditions of sulfuric acid, cuprous oxide can quantitatively consume the iodine produced by potassium iodate and potassium iodide.The remaining iodine in the solution is thiosulfur

Titrate the sodium standard solution, and use water instead of the sample solution to do the blank titration. Substitute the titration difference between the blank and the sample solution.

The linear equation of the liquid calculates the soluble sugar content in the sample.

4 Reagent

Unless otherwise specified, the reagents used in this method are of analytical grade, and the water is Grade III water specified in GB/T 6682.

4.1

Anhydrous sodium carbonate (Na2CO3).

4.2

Sodium potassium tartrate (KNaC4H4O6 · 4H2O).

4.3

Copper sulfate (CuSO4 · 5H2O).

4.4

Sodium bicarbonate (NaHCO3).

4.5

Potassium iodide (KI).

4.6

Potassium iodate (KIO3).

4.7

absolute ethanol (C2H5OH).

4.8

Potassium oxalate (K2C2O4 · H2O).

4.9

Sulfuric acid (H2SO4).

4.10

Zinc sulfate (ZnSO4 · 7H2O).

4.11

Potassium ferrocyanide ([K4Fe (CN) 6] · 3H2O).

4.12

Hydrochloric acid (HCl).

4.13

Sodium hydroxide (NaOH).

4.14

Sodium thiosulfate (Na2S2O3 · 5H2O).

4.15

Glucose (C6H12O6).

4.16

Soluble starch.

4.17

Methyl red (C15H15O2N3).

4.18 Copper sulfate solution (100g/L)

Weigh 10g of copper sulfate (4.3) in water and make up to 100mL.

4.19 Alkaline copper reagent

Weigh 25.0g of anhydrous sodium carbonate (4.1) and 25.0g of sodium potassium tartrate (4.2) in a 1000mL beaker,

It was dissolved in 500 mL of water. 75 mL of copper sulfate solution (4.18) was added below the liquid level through the funnel. Then add 20.0g of sodium bicarbonate (4.4), after it is completely dissolved, 5.0 g of potassium iodide (4.5) is added, and finally transferred into a 1000 mL volumetric flask. Accurately weigh 0.8917g of iodine

Potassium acid (4.6) (dried at 105 ° C for 2h), dissolved in water, and transferred to the above volumetric flask, made up to volume with water, filtered and used overnight.

4.20 Ethanol solution (41)

Measure 800mL of absolute ethanol (4.7) and dilute to 1000mL with water.

4.21 Potassium iodide-potassium oxalate solution

Weigh 2.5g of potassium iodide (4.5) and 2.5g of potassium oxalate (4.8) in water and dilute to 100mL.

Validity period is 7d.

4.22 Sulfuric acid solution (1mol/L)

Measure 56mL of sulfuric acid (4.9) and slowly add it to 800mL of water and dilute to 1000mL.

4.23 Zinc sulfate solution (300g/L)

Weigh 30g zinc sulfate (4.10) to dissolve in water, and make up to 100mL.

4.24 Potassium ferrocyanide solution (150g/L)

Weigh 15g potassium ferrocyanide (4.11) in water and make up to 100mL.

4.25 Hydrochloric acid solution (1 1)

Measure 500mL of hydrochloric acid (4.12) and dilute to 1000mL with water.

4.26 Sodium hydroxide solution (1mol/L)

Weigh 40.00g of sodium hydroxide (4.13) in a 250mL beaker.

1000mL.

4.27

Sodium thiosulfate standard solution (0.1mol/L). Weigh 26.00g of sodium thiosulfate (4.14) and 0.2g of anhydrous sodium carbonate (4.1) to dissolve

In 1000mL of water, boil slowly for 10min. After cooling, make up to 1000mL with boiling and cooling water. Store in brown bottle, store in low

In warm and dark places, use after calibration according to GB/T 601.

4.28

Sodium thiosulfate standard working solution (0.005mol/L). It is accurately diluted from sodium thiosulfate standard solution (4.27). Active use

Match, valid for 24h.

4.29 Glucose standard solution

Accurately weigh 0.1250g of glucose (4.15) dried at 96 °C ± 2 °C for 2h.

250mL. This solution is equivalent to 0.5 mg glucose per milliliter.

4.30 Starch indicator

Weigh 1.0g of soluble starch (4.16) in a beaker, add a small amount of cold water to make a paste, add 100mL to boil

Water, then continue to boil, cool it, store in a drip bottle, and store in the refrigerator.

4.31 Methyl red indicator (1g/L)

Weigh 0.1g of methyl red (4.17) and dissolve it in absolute ethanol (4.7), and make it to 100mL.

5 Instruments and equipment

5.1 Analytical balance

Sensitivity 0.1mg.

5.2

Experimental grinding.

5.3

Electric hot water bath.

5.4 Basic burette

25mL.

5.5 Volumetric flask

100mL.

5.6 Test tube with stopper scale

50mL.

6 Analysis steps

6.1 Sample preparation

Divide not less than 20g of the test sample that is mixed uniformly, and crush it with an experimental mill (5.2) so that 90% of the sample passes through the hole diameter of 0.425mm (40 mesh) test sieve, combine the upper and lower sieve, mix thoroughly, save at room temperature for future use.

6.2 Sample processing

Weigh sample (6.1) 1g ~ 5g (accurate to 0.0001g, preferably with soluble sugar at 40mg ~ 80mg) to 100mL volumetric flask (5.5), add about 80mL of ethanol solution (4.20) and extract in 80 °C water bath for 30min, shaking several times during the period. After cooling with ethanol solution (4.20) Fix volume and filter. Take 50mL of the filtrate in a 100mL evaporating dish and evaporate the ethanol on a 60 °C ~ 70 °C water bath to 2mL ~

When 3mL, add 1mL each of zinc sulfate solution (4.23) and potassium ferrocyanide solution (4.24), shake well, and then wash into a 50mL volumetric flask

Medium, constant volume, filtration. Take 25mL of the filtrate in a 50mL volumetric flask, add 2.5mL of hydrochloric acid solution (4.25), and hydrolyze in a water bath at 80 °C

After 10 minutes, add two drops of methyl red indicator (4.31) after cooling, neutralize to neutral with sodium hydroxide solution (4.26), and make up to volume with water.

6.3 Standard curve drawing

Accurately draw 1.00mL, 2.00mL, 3.00mL, 4.00mL, 5.00mL glucose standard solution (4.29) (equivalent to 0.5mg,

1.0mg, 1.5mg, 2.0mg, 2.5mg glucose) in 50mL stoppered test tube (5.6), add water to make up to 5.00mL. Join

5.0mL of basic copper reagent (4.19) was placed in a boiling water bath and heated for 15min. Immediately after taking out, cool it in cold water for 5min, add it along the tube wall

2mL potassium iodide-potassium oxalate solution (4.21), then add 3mL sulfuric acid solution (4.22), immediately shake to completely dissolve the copper oxide (no acid added

Do not shake before). When titrating to a light yellow-green color with sodium thiosulfate standard working solution (4.28), add 6 drops of starch indicator (4.30),

Continue the titration until the blue color disappears as the end point. At the same time, water was used as a blank instead of the glucose standard solution.

Take the mass of standard glucose (mg) as the abscissa, and take the difference between the titration of the blank test and the standard glucose solution as the ordinate.

Quasi-curve.

6.4 Determination of sample

According to the content of soluble sugar in different samples, draw 6.2mL ~ 5.00mL of 6.2 sample treatment solution, add water to make up to 5.00mL.

The operation is as follows from 6.3 "Adding 5.0mL alkaline copper reagent (4.19)", and water is used instead of the sample solution to make a blank. Blank and try

The difference between the sample titration and the standard curve can be used to obtain the sugar content in the sample solution, so as to calculate the soluble sugar content in the sample.

7 Results calculation

The content of soluble sugar in the sample is calculated according to formula (1).

X = m/100 × 25/50 × V × 100 × (1-H) ×

100 (1)

Where.

X --- the content of soluble sugar in the sample (expressed on a dry basis), the unit is grams per hundred grams (g/100g);

A --- Substitute the difference between the blank and the sample titration into the standard curve to obtain the mass of glucose in the sample solution, the unit is milligram (mg);

m --- sample mass, unit is gram (g);

V --- the volume of sample liquid absorbed during the measurement, the unit is milliliter (mL);

H --- moisture content of the sample, the unit is grams per hundred grams (g/100g).

Take the average of the two measurement results, the calculation results are retained to two decimal places.

When the measurement results do not meet the repeatability requirements, the measurement shall be re-measured according to the provisions of GB/T 5490, and the results shall be calculated.

8 Precision

The absolute difference between two independent determination results obtained under repeatable conditions should not exceed 10% of the arithmetic mean.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 37493-2019

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 37493-2019

$75.00