GB/T 37359-2019Test method of activity for palladium carbon catalysts (English PDF)
钯炭催化剂活性试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 37359-2019 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
March 25, 2019
Implementation date
February 1, 2020
Scope
GB/T 37359-2019 is the English-translated version of 钯炭催化剂活性试验方法.
GB/T 37359-2019 is the Chinese standard "Test method of activity for palladium carbon catalysts". Its scope clause reads: This Standard specifies the test method of activity for palladium carbon catalysts.
This Standard applies to palladium carbon catalysts of hydrogenation reduction reactions for petrochemical industry, pharmaceutical intermediates, electronics industry, perfume industry, dye industry and other fine chemicals, which takes wood powdered activated carbon as the carrier and palladium as the main active component.
Its clauses include principle; reagents or materials; test device; sample; test procedures; test data processing. It was issued by the State Administration for Market Regulation on MARCH 25, 2019 and took effect on FEBRUARY 01, 2020.
Found what you need?
Document preview — GB/T 37359-2019
National Standard of the People's Republic of China
- ICS
- 71.100.99
- Classification
- G 74
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword3
- 1 Scope4
- 2 Normative references4
- 3 Principle4
- 4 Reagents or materials4
- 5 Test device5
- 6 Sample6
- 7 Test procedures7
- 8 Test data processing8
1 Scope
This Standard specifies the test method of activity for palladium carbon catalysts.
This Standard applies to palladium carbon catalysts of hydrogenation reduction reactions for petrochemical industry, pharmaceutical intermediates, electronics industry, perfume industry, dye industry and other fine chemicals, which takes wood powdered activated carbon as the carrier and palladium as the main active component.
2 Normative references
The following documents are indispensable for the application of this document.
For dated references, only the dated version applies to this document. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 6679, General rules for sampling solid chemical products
GB/T 6682, Water for analytical laboratory use. Specification and test methods
3 Principle
The N-benzylaniline in the raw material, under certain temperature and pressure and the action of a palladium carbon catalysts, reacts with hydrogen to generate aniline and toluene. The chemical reaction formula is as follows:
Use a gas chromatograph to determine the mass fraction of N-benzylaniline before and after the reaction; calculate the conversion rate of N-benzylaniline, to characterize the activity of the catalyst.
4 Reagents or materials
4.1 N-Benzylaniline: purity greater than 99.0%
Weigh 0.010 0 g of the catalyst sample corresponding to palladium; accurate to 0.000 1 g; put aside for use.
7 Test procedures
Warning -- The test materials and reagents which are involved in this Standard have toxic, flammable, and explosive hazards to human health and safety. System leakage shall be strictly prevented; open flames are strictly forbidden on the site; preventive facilities such as necessary fire extinguishing equipment and exhaust equipment shall be equipped; it is strictly forbidden to carry out disassembly operation of autoclave under pressure. This Standard does not reveal all possible safety issues; users shall use it strictly in accordance with relevant regulations, and have the responsibility to take appropriate safety and health measures.
7.1 Filling of the reactor
Add 30.0 g of N-benzylaniline, 150 mL of ethanol, 1.0 mL of formic acid, and catalyst samples (see 6.3) to the clean and dry reactor in order; cover the kettle lid; tighten the nuts evenly; then, connect it to the system.
7.2 Leakage test
Open the nitrogen valve; introduce nitrogen into the system; boost the system to 0.50 MPa; close the inlet and outlet valves of the system. If the pressure drop is less than 0.05 MPa within 30 min, the system is considered to be sealed.
Open the system outlet valve to reduce the pressure of the system to normal pressure; insert the temperature measuring thermocouple into the thermowell.
7.3 Gas replacement and activity determination
Use nitrogen to replace the system for 3 times; then, exhaust and reduce the pressure to normal pressure. Switch to hydrogen and replace for 3 times; then, exhaust and reduce the pressure to normal pressure. Warm and heat the reactor. When the temperature of the reactor is raised to 50°C, increase the system pressure to 0.50 MPa. Control and maintain the reactor pressure at 0.50 MPa, the temperature at 50°C, and the stirring speed at 900 r/min. After 20 minutes, end the test.
7.4 Power-off
Turn off the hydrogen and turn on the cooling water; after the temperature of the reactor drops to below 40°C, release the pressure. Use nitrogen to replace the system for 3 times; perform sampling and analysis; use deionized water to clean the reactor body. […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 37359-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 6679-2003 — General rules for sampling solid chemical products
GB/T 6682-2008 — Water for analytical laboratory use - Specification and test methods
GB/T 7251.4-2026 — Low-voltage switchgear and controlgear assemblies - Part 4: Particular requirements for assemblies for construction sites (ACS)
Secure payment via Stripe
Payments accepted
GB/T 37359-2019
$90.00