Valid

GB/T 36703-2018Hydraulic fluid power -- Pressure switches -- Mounting surfaces (English PDF)

液压传动 压力开关 安装面

Preview PDF

This is a limited preview

Buy now to download the full PDF (17 pages)

Need quotation for your management?

Get a formal quotation for GB/T 36703-2018 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

September 17, 2018

Implementation date

April 1, 2019

Scope

GB/T 36703-2018 is the English-translated version of 液压传动 压力开关 安装面.

GB/T 36703-2018 — This standard specifies the mounting surface of the pressure switch and provides a reference for the standardized arrangement of pressure switches, hydraulic valves and mounting plates.

Found what you need?

Document preview — GB/T 36703-2018

National Standard of the People's Republic of China

ICS
23.100.50
Classification
J 20

Issued by: State Administration for Market Regulation, China National Standardization Administration

Contents

  • Foreword
  • Introduction
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 symbol
  • 4.1 This standard uses the following symbols.
  • 4.2 The mounting surface code shall comply with the marking rules specified in ISO 5783.
  • 5 tolerance
  • 6 dimensioning

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009.

This standard uses the translation method equivalent to ISO 16873.2011 "hydraulic transmission pressure switch mounting surface".

The documents of our country that have a consistent correspondence with the international documents referenced in this standard are as follows.

---GB/T 14043-2005 Hydraulic transmission valve mounting surface and the identification code of the cartridge valve hole (ISO 5783.1995, IDT);

---GB/T 17446-2012 Fluid drive system and component vocabulary (ISO 5598.2008, IDT).

This standard has made the following editorial changes.

--- The reference dimensions in Figures 1 and 2 are bracketed by national standards.

This standard was proposed by the China Machinery Industry Federation.

This standard is under the jurisdiction of the National Hydraulic and Pneumatic Standardization Technical Committee (SAC/TC3).

This standard was drafted. Beijing Huade Hydraulic Industry Group Co., Ltd., Beijing Machinery Industry Automation Research Institute Co., Ltd.

Feibao Power Technology Co., Ltd., Shandong Zhongchuan Hydraulic Co., Ltd.

Introduction

In hydraulic systems, power is transmitted and controlled through pressurized fluid in a closed circuit, which is an important component of the system.

When the preset pressure is reached, the switch contacts act.

Hydraulic transmission pressure switch mounting surface

1 Scope

This standard specifies the mounting surface of the pressure switch and provides a reference for the standardized arrangement of pressure switches, hydraulic valves and mounting plates.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest edition (including all amendments) applies to this document.

ISO 3601-2.2008 Fluid transmission systems - O-rings - Part 2. s

tems-O-rings-Part 2. Housingdimensionsforgeneralapplications)

ISO 5598 Hydraulic Drive System and Component Vocabulary (Fluidpowersystemsandcomponents-Vocabulary)

ISO 5783 Hydraulic Drive Valve Mounting Surface and Cartridge Valve Hole Identification Rules (Hydraulicfluidpower-Codeforidenti-

Ficationofvalvemountingsurfacesandcartridgevalvecavities)

3 Terms and definitions

The terms and definitions defined in ISO 5598 apply to this document.

4 symbol

4.1 This standard uses the following symbols.

P and L---port;

F---threaded hole;

G--- positioning pin hole.

4.2 The mounting surface code shall comply with the marking rules specified in ISO 5783.

5 tolerance

The mounting surface (ie the area within the dashed line in Figures 1 and 2) shall meet the following requirements.

---Surface roughness. see ISO 3601-2.2008, 5.1.4 and 5.2.3;

---Surface flatness. see ISO 3601-2.2008, 5.1.4;

---Locating pin hole diameter tolerance. H12.

6 dimensioning

The dimensions of the mounting surface of the pressure switch are shown in Figure 1 and Figure 2, respectively.

Mounting surface of pressure switch with P port (code. GB/T xxxx-01-01-0-xxxx)

Mounting surface of pressure switch with P and L ports (code. GB/T xxxx-01-02-0-xxxx)

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.

Referenced standards

Normative references

ISO 3601 · ISO 5598 · ISO 5783

How to Download GB/T 36703-2018

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
17 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 36703-2018

$115.00