Valid

GB/T 36671-2018Design requirements for high speed shafting of OSV (English PDF)

海洋工程船高速轴系设计要求

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 36671-2018 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

September 17, 2018

Implementation date

April 1, 2019

Scope

GB/T 36671-2018 is the English-translated version of 海洋工程船高速轴系设计要求.

GB/T 36671-2018 gives the requirements for designing, manufacturing, installing, inspecting and testing the high-speed shafting of offshore engineering vessels.

High-speed shafting is the part between the prime mover and the gearbox that does not carry propeller thrust and turns at 400 r/min or more. The standard applies to vessels driven by controllable-pitch propellers or azimuth thrusters, and other ships may use it for reference.

It defines thrust shafting, azimuth thrusters, and zigzag and linear high-speed shafting, and requires sufficient strength and rigidity, no torsional, lateral or longitudinal resonance across the engine operating range, good tolerance of hull deformation and at least one flexible coupling.

It also covers design principles, the test report and annexes on shaft blanks, shaft machining and installation. It was issued on 17 September 2018 and has applied since 1 April 2019.

Found what you need?

Document preview — GB/T 36671-2018

National Standard of the People's Republic of China

ICS
47.020.20
Classification
U 48

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Terms and Definitions
  • 4 General requirements
  • 5 Design Principle
  • 6 Manufacturing requirements
  • 7 Installation requirements
  • 8 Test report
  • Appendix A (informative) Shaft blank requirements
  • Appendix B (Normative) Shaft processing requirements
  • Appendix C (informative) Installation of the shafting
  • Reference

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009.

1 Scope

This standard specifies the requirements for the design, manufacture, installation, inspection and testing of high-speed shafting of marine engineering vessels.

This standard is applicable to the high-speed shafting of ships of marine engineering vessels with pitch-controlled paddles and full-rotary rudder propellers as the main thrusters. For other ships The high-speed shaft system can also be used as reference.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest edition (including all amendments) applies to this document.

CB/T 4312 shaft forging technical conditions

3 Terms and definitions

The following terms and definitions apply to this document.

3.1 High speed shafting

Located between the prime mover and the gearbox, it does not withstand the thrust generated by the propeller, and the shaft segment with a speed of not less than 400r/min and its annex.

3.2 Thrust shafting

A shaft section and its accessories that are placed between the gearbox and the propeller while receiving the thrust generated by the propeller.

3.3 Full-rotation rudder propeller device

A propulsion device capable of rotating 360° around a rotation axis and capable of transmitting thrust at an arbitrary angle while having the function of a rudder.

3.4 High-speed zigzag shaft

The centerline of the shafting is not on the same axis and is the high-speed shaft of the fold line.

3.5 Linear shafting

The centerline of the shafting system is on the same axis and is a linear high-speed shaft system.

4 General requirements

4.1 In the range of main engine operating conditions, the high speed shafting should have sufficient strength and rigidity, stable and reliable.

4.2 In the range of main engine operating conditions, the torsional resonance and lateral and longitudinal resonance should not occur in the high speed shafting.

4.3 The high speed shafting should have good deformation adaptability to the ship.

4.4 One or more flexible couplings shall be designed for high speed shafting.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download GB/T 36671-2018

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 36671-2018

$235.00