Valid

GB/T 36586.2-2018Tools for pressing -- Wear plates -- Part 2: Type B (English PDF)

冲模耐磨板 第2部分:B型

Preview PDF

This is a limited preview

Buy now to download the full PDF (21 pages)

Need quotation for your management?

Get a formal quotation for GB/T 36586.2-2018 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

September 17, 2018

Implementation date

April 1, 2019

Scope

GB/T 36586.2-2018 is the English-translated version of 冲模耐磨板 第2部分:B型.

GB/T 36586.2-2018 is Part 2 of the two-part Chinese national standard series on wear plates for pressing tools, and it covers the type B plate.

It specifies the basic dimensions and the tolerances of type B wear plates for large dies and specifies the dimensions and the positions of the mounting holes; it gives a description of the material and the hardness and specifies the marking of a type B wear plate for dies that meets its requirements.

It applies to type B wear plates for large dies. Clause 2 fixes the structural type and the dimensions, which shall comply with the requirements of Figure 1, Figure 2 and Table 1, with dimensions in millimetres and surface roughness values in micrometres.

It modifies ISO 9183-2:2011 by the redrafting method, with the dimension 21 plus or minus 0.25 in Figure 1 changed to the actual thickness t so that no machining allowance need be reserved, the value 20 of t in Table 1 changed to 20 nought to minus 0.02, and ISO 1302:2002 in the references replaced by the equivalent GB/T 131-2006. It was issued on 17 September 2018 and has applied since 1 April 2019.

Found what you need?

Document preview — GB/T 36586.2-2018

National Standard of the People's Republic of China

ICS
25.120.10
Classification
J 46

Issued by: State Administration for Market Regulation, China National Standardization Administration

Contents

  • Foreword
  • 1 Scope
  • 2 Size

Foreword

GB/T 36586 "die wear plate" consists of 2 parts.

--- Part 1. Type A;

--- Part 2. Type B. This part is the second part of GB/T 36586.

This part is drafted in accordance with the rules given in GB/T 1.1-2009.

This section uses the redrafting method to modify the use of ISO 9183-2:2011 "die die wear plate part 2. B type".

There are technical differences in this section compared to ISO 9183-2:2011, and the terms involved in these differences have been passed on the outside margins.

The vertical single line ( - ) of the position is marked. The corresponding technical differences and their reasons are as follows.

---Modified the dimension "21±0.25" in Figure 1 as t, t is the actual size, no need to reserve machining allowance; delete the original drawing t and the double-dot line indicating the corresponding requirement.

--- Change the value 20 of t in Table 1 to 20 0-0.02 to meet the current technology and product actual conditions. This section has made the following editorial changes.

---Modified standard name;

--- Deleted the description of "Unit is mm" in "1 Scope";

---In the "1 Scope", added "this part is suitable for B-type wear plates for large die";

--- In the "2 size", the "B type wear plate size should comply with the requirements of Figure 1, Figure 2 and Table 1" modified to "B type wear plate knot The configuration and dimensions shall comply with the requirements of Figure 1, Figure 2 and Table 1";

--- Modified "Figure 1" picture title "size" as "B type wear plate";

--- In the upper right corner of Figure 2, the label "in millimeters" has been added;

---Modified the location of some dimensions, tolerances, and roughness in Figure 1, Figure 2, and modified the marking according to the national standard of technical drawings. the way;

--- References, replaced by ISO 1302:2002 with GB/T 131-2006 equivalent to the international standard.

1 Scope

This part of GB/T 36586 specifies the basic dimensions and tolerances of B-type wear plates for large die and specifies the dimensions of the mounting holes. And location.

This section gives a description of the material and hardness, and specifies the marking of the B-type wear plate for the die that meets the requirements of this section.

This section applies to B-type wear plates for large die.

2 Size

The structural type and dimensions of the B-type wear plate shall comply with the requirements of Figure 1, Figure 2 and Table 1.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 21 pages — is available in the English PDF.

How to Download GB/T 36586.2-2018

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
21 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 36586.2-2018

$85.00