Valid

GB/T 36524-2018Tools for pressing -- Compression springs with rectangular section -- Housing dimensions and colour coding (English PDF)

冲模 矩形截面压缩弹簧 安装尺寸和颜色标识

Preview PDF

This is a limited preview

Buy now to download the full PDF (29 pages)

Need quotation for your management?

Get a formal quotation for GB/T 36524-2018 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

July 13, 2018

Implementation date

February 1, 2019

Scope

GB/T 36524-2018 is the English-translated version of 冲模 矩形截面压缩弹簧 安装尺寸和颜色标识.

GB/T 36524-2018 — This standard specifies the technical requirements for compression springs made of rectangular cross-section metal wires and gives the color of each spring grade.

Logo. This standard parameter applies to the installation of the spring, does not specify the quality of the spring itself, nor does it cover all spring sizes (such as section size), Material or life.

This standard divides springs into four grades. light, medium, heavy and extra heavy.

Found what you need?

Document preview — GB/T 36524-2018

National Standard of the People's Republic of China

ICS
01.070; 25.120.10
Classification
J 46

Issued by: State Administration for Market Regulation, China National Standardization Administration

Contents

  • Foreword
  • 1 Scope
  • 2 Technical requirements
  • 2.1 General requirements
  • 2.2 Tolerance of free length L0

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009.

This standard uses the redrafting method to modify the ISO 10243.2010 "die rectangular section compression spring installation size and color standard

knowledge".

There are technical differences between this standard and ISO 10243.2010. The terms involved in these differences have been passed through the margins on the outer side of the page.

The vertical single line (—) is marked. The corresponding technical differences and their reasons are as follows.

--- Change the tolerance "+/-1%" in Table 1 to "+/-1%L0" to make the statement clearer.

This standard also made the following editorial changes.

---Modified the tolerance of "2.2 free length L0" "The tolerance of free length L0 should meet the requirements of Figure 1 and Table 1."

The tolerance of length L0 shall be in accordance with Table 1. ";

--- Removed the separator between the size code or the value and the unit in Table 2~Table 5.

This standard is proposed and managed by the National Die Standardization Technical Committee (SAC/TC33).

This standard was drafted. Anhui Jianghuai Automobile Group Co., Ltd., Changzhou Dongli Machinery Co., Ltd., Anhui Qingtian Weijia equipment

Manufacturing Co., Ltd., South China University of Technology, Dongguan Zhengbiao Testing Technology Co., Ltd., Ningbo Hongxie Co., Ltd., Anhui University of Architecture,

Xiamen Meike Security Technology Co., Ltd., Zhejiang Ouyi Smart Kitchen Co., Ltd., Xi'an Xumai Intelligent Appliance Technology Co., Ltd., Guilin

Electrical Science Research Institute Co., Ltd.

1 Scope

This standard specifies the technical requirements for compression springs made of rectangular cross-section metal wires and gives the color of each spring grade.

Logo.

This standard parameter applies to the installation of the spring, does not specify the quality of the spring itself, nor does it cover all spring sizes (such as section size),

Material or life.

This standard divides springs into four grades. light, medium, heavy and extra heavy.

2 Technical requirements

2.1 General requirements

Compression springs conforming to this standard shall comply with the requirements of Figures 1 and 2.2 to 2.6.

Figure 1 compression spring

2.2 Tolerance of free length L0

The tolerance of the free length L0 shall be in accordance with Table 1.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 29 pages — is available in the English PDF.

How to Download GB/T 36524-2018

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
29 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 36524-2018

$235.00