GB/T 35855-2018Identification marking of aircraft electrical cables (English PDF)
飞机电缆标识
This is a limited preview
Buy now to download the full PDF (17 pages)
Need quotation for your management?
Get a formal quotation for GB/T 35855-2018 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
February 6, 2018
Implementation date
February 6, 2018
Scope
GB/T 35855-2018 is the English-translated version of 飞机电缆标识.
GB/T 35855-2018 — This standard specifies the marking method for single-core, multi-core and coaxial wire and cable for aircraft wiring, indicating the types and specifications of wires and cables.
Source, production date, etc., to facilitate the maintenance of wire and cable and failure analysis, but also to use the same wire and cable replacement when necessary.
Simultaneously, This standard also specifies the marking method of insulated wire cores. This standard supplements existing identification information and also takes into consideration the manufacturers of each country.
The code. This standard applies to the identification of aircraft wire and cable.
Found what you need?
Document preview — GB/T 35855-2018
National Standard of the People's Republic of China
- ICS
- 49.060
- Classification
- V 40
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Cable identification
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
This standard uses the translation method equivalent to using ISO 2574.1994 "Aircraft cable identification."
This standard made the following editorial changes.
---3.2 added a description of the identification example;
--- ISO 2574.1994 Table 2 As of.2015, a "note" has been added to Table 2 of this standard, which has been expanded according to its coding rules;
--- Table 8 adds a "note", the necessary identification of the method of identification.
This standard was proposed by China Aviation Industry Corporation.
This standard is under the jurisdiction of the National Aircraft Standardization Technical Committee (SAC/TC435).
This standard was drafted by Shaanxi Aviation Electric Co., Ltd., Hefei Jianghang Aircraft Equipment Co., Ltd., and China Aviation Comprehensive Technology Research Institute.
Research Institute, Baosheng Technology Innovation Co., Ltd., Guangzhou Kaiheng Special Wire & Cable Co., Ltd., Shenyang Xinghua Aviation Electric Co., Ltd.
1 Scope
This standard specifies the marking method for single-core, multi-core and coaxial wire and cable for aircraft wiring, indicating the types and specifications of wires and cables.
Source, production date, etc., to facilitate the maintenance of wire and cable and failure analysis, but also to use the same wire and cable replacement when necessary. Simultaneously,
This standard also specifies the marking method of insulated wire cores. This standard supplements existing identification information and also takes into consideration the manufacturers of each country.
The code.
This standard applies to the identification of aircraft wire and cable.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest version (including all amendments) applies to this document.
ISO 3166.1993 Codesfortherepresentationofnamesofcountries
3 Cable identification
3.1 Due to the different requirements for cable sheathing, the minimum size of cable that can be marked depends on the outside diameter and should be performed in the cable specification
Provisions.
The marking shall include a set of codes, which are in accordance with the specification symbols specified in the relevant national standards, using contrasting colors of green or sheath colors.
Marking, repeat every 300mm +/- 50mm, its contents include.
--- Cable name or specification/standard number, model number and specification (specification code according to Table 1);
--- Country of origin code, alpha-2 code according to ISO 3166;
--- manufacturer code, in accordance with the relevant provisions of the country of origin;
--- Production year code according to Table 2.
Table 1 Cable specification codes
Nominal section
Mm2
Specification code
EN AWG
0.15 001 26
0.25 002 24
0.4 004 22
0.6 006 20
1.2 012 16
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.
Referenced standards
Normative references
ISO 3166.1993
How to Download GB/T 35855-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 35855-2018
$125.00