GB/T 34638-2017Non-destructive testing—Test methods for ultrasonic leak detection (English PDF)
无损检测 超声泄漏检测方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 34638-2017 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
September 29, 2017
Implementation date
April 1, 2018
Scope
GB/T 34638-2017 is the English-translated version of 无损检测 超声泄漏检测方法.
GB/T 34638-2017 is the Chinese standard "Non-destructive testing—Test methods for ultrasonic leak detection". Its scope clause reads: This standard specifies the ultrasonic leak detection method and the results of evaluation.
This standard applies to the working medium for the gas or liquid in the use of airtight equipment or components during the operation of the leak detection. Its clauses include terms and definitions; method summary.
Found what you need?
Document preview — GB/T 34638-2017
National Standard of the People's Republic of China
- ICS
- 19.100
- Classification
- J 04
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Method summary
1 Scope
This standard specifies the ultrasonic leak detection method and the results of evaluation.
This standard applies to the working medium for the gas or liquid in the use of airtight equipment or components during the operation of the leak detection.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version applies to this article
Pieces. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 9445 non-destructive testing personnel qualification and certification
GB/T 12604.7 Non-destructive testing term leak detection
GB/T 20737 non-destructive testing common terms and definitions
3 Terms and definitions
GB/T 12604.7 and GB/T 20737 defined terms and definitions apply to this document.
4 Method summary
Ultrasonic leak detection technology is the use of ultrasonic technology to detect leaks, with easy to operate, fast, environmentally friendly and low cost special point. For fluid-filled containment devices, when the internal pressure is greater than the external pressure, once a leak occurs, the fluid medium due to internal and external pressure
The existence of the hole will be punched out. When the size of the leak hole is small, the flushing fluid forms a turbulent flow, and the turbulent flow will generate a certain frequency near the leak hole
Sound waves and can spread in the air. The main frequency of acoustic vibration and leaky hole size, when the frequency of 20Hz ~ 20kHz, the human ear can hear
To leak sound, when the frequency is greater than 20kHz, the ultrasonic signal. Ultrasound has good directivity, its intensity with the propagation distance
Increase and rapidly decay, through the use of specialized instruments to detect the energy of these ultrasonic signals can determine the location of the leak and measure the leak small. Figure 1 shows the schematic diagram of ultrasonic leak detection. The ultrasonic signal generated by the leak can be received by the ultrasonic leak detector through the probe. versus
Compared to most leak detection methods, the sensitivity of the ultrasonic leak detection method is low, and the pressure conditions of the device under test, the size of the leak hole, the leak
Hole location and probe spacing and other factors, the maximum sensitivity of the existing equipment 1 × 10-3Pa · m3/s, does not apply to have a fatal or dangerous
Acceptance testing of airtight equipment for hazardous substances.
Ultrasonic leak detection principle shown in Figure 1.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 34638-2017
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 34638-2017
$145.00