GB/T 34582-2017Single cell and stack performance test methods for solid oxide fuel cells (SOFC) (English PDF)

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009.

This standard uses the translation method identical with IEC TS62282-7-2:2014 "Fuel Cell Technology Part 7-2. Test Method Solid Body oxide fuel cell (SOFC) cell and stack performance test. " the documents of our country that are consistent with the corresponding international documents that are normative references in this standard are as follows.

--- GB/T 5274-2008 preparation of gas mixture for gas analysis calibration method (ISO 6142:2001, IDT)

--- GB/T 5275.7-2014 Gas analysis Dynamic volume method for the preparation of calibration gas mixtures Part 7. Thermal mass flow Volume Controller (ISO 6145-7:2009, IDT)

--- GB/T 10628-2008 gas analysis calibration gas mixture composition determination and comparison test (ISO 6143:2001, IDT) Petroleum products and determination of sulfur content of hydrocarbon compounds Wickbold combustion method (ISO 4260).

1987, IDT)

--- GB/T 13277.1-2008 compressed air Part 1. Pollutant purification level (ISO 8573-1:2001, MOD)

--- GB/T 16839.1-1997 Thermocouple Part 1. Index table (idtIEC 60584-1.1995)

--- GB/T 16839.2-1997 Thermocouple Part 2. Tolerance (idtIEC 60584-2.1982)

--- GB/T 18404-2001 armored thermocouple cable and armored thermocouple (idtIEC 61515.1995)

--- GB/T 27759-2011 fluid flow measurement uncertainty assessment procedures (ISO 5168:2005, IDT)

--- GB/T 27894 (all parts) of natural gas under certain uncertainty by gas chromatography to determine the composition [ISO 6974 Some part)]

--- GB/T 28816-2012 Fuel Cell Terminology (IEC TS62282-1:2010, IDT) for ease of use, this standard made the following editorial changes.

--- Modify the standard name;

--- 10.7.3 added a note "typical solid oxide fuel cell negative impedance spectrum shown in Figure 2";

--- 11.6 added a note "see Appendix G".

This standard proposed by the China Electrical Equipment Industry Association.

This standard by the National Fuel Cell and Flow Battery Standardization Technical Committee (SAC/TC342) centralized.

This standard drafting unit. China University of Mining and Technology, Shanghai Jiaotong University, Zhong Yu Hydrogen Technology (Jingzhou) Co., Ltd., Suzhou Huaqing Jingkun new Source Technology Co., Ltd., Guangdong that have access to Energy Technology Co., Ltd., Shanghai Institute of Quality Supervision, Inspection Technology, machinery industry Beijing Electrician Institute of Technology and Economy, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Anhui Institute of Quality and Standardization, Harbin Institute of Technology, Tsinghua University University, Wuhan University of Technology, Beijing Qunling Energy Technology Co., Ltd., Ji Shier (Hefei) Energy Technology Co., Ltd., Huazhong University of Science and Technology.

1 Scope

This standard specifies the test system for solid oxide fuel cell and battery stack (hereinafter referred to as single cell/stack) combination unit test Systems, instrumentation and test methods for testing the performance of solid oxide fuel cell stacks.

This standard does not apply to small button batteries. Small coin cell batteries can be used for solid oxide fuel cell material testing, can not provide Fuel utilization measurement method.

This standard is used for data exchange in commercial transactions between cell/heap manufacturers and system developers or for collecting cell/heap Data to evaluate the performance of a system based on this cell/heap. Users of this standard can choose from a number of projects that fit their purpose Perform the test.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version applies to this article Pieces. For undated references, the latest edition (including all amendments) applies to this document.

IEC 60584-1 Thermocouples - Part 1. EMC Specifications and Tolerances (Thermocouples-Part 1: EMFspecifications andtolerances) IEC 60584-2 Thermocouples Part 2. Tolerances (Thermocouples-Part 2. Tolerances) IEC 60584-3 Thermocouples - Part 3. Extension and compensation cables - Tolerance and qualification systems (Thermocouples - Part 3.

Extension and compensatingcables-Tolerancesandidentificationystem) IEC 61515 armored thermocouple cables and armored thermocouple (Mineralinsulatedthermouplecablesandthermo-couples IEC TS62282-1:2013 Fuel Cell Technology Part 1. Terms (Fuelceltechnologies-Part 1: Termi-nology ISO 4260 Determination of sulfur content of petroleum products and hydrocarbon compounds Wickbold combustion method (Petroleumproductsand hydrocarbons-Determinationofsulfurcontent-Wickboldcombustionmethod) ISO 5168 fluid flow measurement uncertainty assessment procedures (Measurementoffflowflow- Proceduresforthe evaluationofuncertainties ISO 6141 gas analysis Calibration gas and gas mixture of the certificate requirements (Gasanalysis-Requirementsfor certificatesforcalibrationgasesandgasmixtures) ISO 6142 gas analysis is more ready to use mixed gas preparation method (Gasanalysis-Preparationofcalibration gasmixtures-Gravimetricmethod) ISO 6143 gas analysis to determine and test calibration gas mixture composition (Gasanalysis-Comparison methodsfordeterminingandcheckingthecompositionofcalibrationgasmixtures) ISO 6145-7 Gas analysis Dynamic volumetric preparation of calibration gas mixtures - Part 7. Thermal mass flow controllers (Gas analysis-Preparationofcalibration gas mixtures using dynamic volumetric methods-Part 7.

Thermalmass-flowcontrolers) ISO 6974 (all parts) Natural gas Determination by gas chromatography with certain uncertainty Composition (Naturalgas-Deter-