GB/T 34478-2017Determination of anti-slip coefficient at bolted connect steel plates' surfaces (English PDF)
钢板栓接面抗滑移系数的测定
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 34478-2017 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
October 14, 2017
Implementation date
July 1, 2018
Scope
GB/T 34478-2017 is the English-translated version of 钢板栓接面抗滑移系数的测定.
GB/T 34478-2017 lays down how the anti-slip coefficient of the bolted surfaces of steel plates is determined.
Clause 1 states that the standard specifies the test principle, the test equipment, the specimens, the test procedure, the revision of the test result value and the test report, and that it applies to the determination of the anti-slip coefficient of steel plate bolted joints made with M12 to M30 10.9S high strength hexagon head bolts and with M16 to M30 10.9S twisted shear high strength bolts; the same clause adds that the determination of the anti-slip coefficient of other friction type metal bolt interfaces may also refer to the standard.
The document is built as nine clauses, namely scope, normative references, terms and definitions, test principle, test equipment, specimen, test procedure, revision of the test result value and test report, followed by a bibliography.
Clause 3 defines four terms: the bolted surface, which is the contact surface between the plates to be connected; the pre-tension force; the slip force, which is the force at the start of slippage of the bolted surface; and the anti-slip coefficient itself, given as the ratio of the slip force to the pre-tension force.
Clause 4 states the principle: the specimen is stretched in a tensile testing machine until it slips, and the anti-slip coefficient follows from the slip force and the sum of the bolt pre-tension forces at the bolted surface.
Clause 2 cites GB/T 228.1, GB/T 8170, GB/T 16825.1-2008 and JJG455. The draft on the page stops at the end of clause 4, so the test equipment, specimen, procedure, result revision and report clauses are not shown.
The page places the standard under ICS 77.040.10 and Chinese classification H22, with an estimated 10,176 words. It was issued on 14 October 2017 and has applied since 1 July 2018.
Found what you need?
Document preview — GB/T 34478-2017
National Standard of the People's Republic of China
- ICS
- 77.040.10
- Classification
- H 22
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Preface
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 test principle
- 5 test equipment
- 6 specimen
- 7 Test Procedure
- 8 test results revised value of about
- 9 Test Report
- References
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This standard specifies the test principle of measuring the anti-slip coefficient of steel bolting surface, test equipment, test pieces, test procedures, the value of the test results Revise and test report.
This standard applies to M12 ~ M30 10.9S high strength hexagon head bolt connection and M16 ~ M30 10.9S twisted shear high Determination of anti - slippage coefficient of steel plate bolted joint with strength bolt connection. Other bolt connection pairs of friction type other metal bolt interface resistance Determination of slip coefficient can also refer to the use of this standard.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version applies to this document. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 228.1 tensile testing of metallic materials - Part 1. room temperature test method
GB/T 8170 rounded repair rules and limit values of the representation and judgment
GB/T 16825.1-2008 static uniaxial testing machine test Part 1. Rally and (or) pressure testing machine force measuring system Inspection and calibration
JJG455 working dynamometer verification procedures
3 Terms and definitions
The following terms and definitions apply to this document.
3.1 Bolted surface
Bolt the contact surface between the plates to be connected.
3.2 Pre-tension
Tighten the bolt, the role of the bolt rod tension or pressure perpendicular to the bolt between the surface.
3.3 Slip force
The force at the start of slippage of the bolted surface.
3.4 Anti-slip coefficient
The ratio of sliding force to pre-tensioning force.
4 Test principle
Tensile test machine in the anti-sliding coefficient of the specimen to be stretched to make it slide the sliding force and the bolt sliding surface of the pre-pull side The sum of force is linear, resulting in anti-slip coefficient.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 228.1Metallic Materials — Tensile Testing — Part 1: Method of Test at Room Temperature
- GB/T 8170Rules of rounding off for numerical values & expression and judgement of limiting values
- GB/T 16825.1-2008Metallic materials - Calibration and verification of static uniaxial testing machines - Part 1: Tension/compression testing machines - Calibration and verification of the force-measuring system
Similar standards
How to Download GB/T 34478-2017
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 16825.1-2008 — Verification of static uniaxial testing machines - Part 1: Tension/compression testing machines - Verification and calibration of the force-measuring system
GB/T 228.1-2010 — Metallic materials - Tensile testing - Part 1: Method of test at room temperature
GB/T 228.1-2021 — Metallic Materials — Tensile Testing — Part 1: Method of Test at Room Temperature
GB/T 34478-2017
$145.00