GB/T 34363-2017Non-destructive testing—Test method for fabricating and checking aluminum alloy ultrasonic standard reference blocks (English PDF)
无损检测 铝合金超声标准试块制作和校验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 34363-2017 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
September 29, 2017
Implementation date
April 1, 2018
Scope
GB/T 34363-2017 is the English-translated version of 无损检测 铝合金超声标准试块制作和校验方法.
GB/T 34363-2017 is the Chinese standard "Non-destructive testing—Test method for fabricating and checking aluminum alloy ultrasonic standard reference blocks".
Its scope clause reads: This standard specifies the aluminum alloy ultrasonic standard test block recommended group, production procedures, physical characteristics of the calibration procedure and ultrasonic response verification procedures.
This standard specifies the aluminum alloy standard test block for ultrasonic testing equipment performance verification can also be used for aluminum products ultrasonic (P wave) pulse Reflective (direct contact or immersion) calibration and control of the test. Its clauses include terms and definitions; method summary.
Found what you need?
Document preview — GB/T 34363-2017
National Standard of the People's Republic of China
- ICS
- 19.100
- Classification
- J 04
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Method summary
- 5 meaning and purpose
- 6 standard test block recommended group
- 7 standard test block material
- 8 standard test block material quality
- 9 standard test block production process
- 10 Physical Characteristics Verification Program
- 11 ultrasonic response characteristic verification program
- 12 Report
1 Scope
This standard specifies the aluminum alloy ultrasonic standard test block recommended group, production procedures, physical characteristics of the calibration procedure and ultrasonic response verification procedures.
This standard specifies the aluminum alloy standard test block for ultrasonic testing equipment performance verification can also be used for aluminum products ultrasonic (P wave) pulse
Reflective (direct contact or immersion) calibration and control of the test.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version applies to this article
Pieces. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 12604.1 Non-destructive testing - Ultrasonic testing
GB/T 20737 non-destructive testing common terms and definitions
GB/T 28880 nondestructive testing without electronic measuring instruments pulse reflection ultrasonic testing system performance characteristics of the assessment
3 Terms and definitions
GB/T 12604.1 and GB/T 20737 and defined by the following terms and definitions apply to this document.
3.1 Angle error angularerror
The maximum number of shots received by the probe from the standard test block or the maximum back reflection and the response of the bottom of the flat bottom hole is not the maximum. when
Ultrasonic incident surface, hole bottom and back are not parallel when there will be angular error.
3.2 Area-amplitude response curve
When the distance from the probe is the same, the response curves of the reflectors with different areas and their ultrasonic responses correspond to each other.
3.3 Metal distance
Standard test block from the ultrasound incident surface to the bottom of the flat-bottomed hole distance.
3.4 Ultrasound response
The display height observed on the screen of the ultrasonic testing instrument reflects the amount of ultrasonic energy initially reflected by the standard test block from the bottom of the hole.
4 Method summary
4.1
The standard test block made of aluminum alloy material after ultrasonic testing should be no significant discontinuity, and then precision machining into a certain height of the circle
Column test block, in the center of the back of the test block processing a constant depth, the provisions of the diameter of the flat bottom hole. Standard test block by flat-bottomed hole diameter, the total test block
Degree or metal distance grouping.
4.2
Each standard test block using a calibrated ultrasonic testing system under the provisions of the detection frequency ultrasonic testing for each test block to establish phase […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 34363-2017
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 34363-2017
$260.00