GB/T 34329-2017General requirements of fiber reinforced plastics pressure vessel (English PDF)
纤维增强塑料压力容器通用要求
This is a limited preview
Buy now to download the full PDF (48 pages)
Need quotation for your management?
Get a formal quotation for GB/T 34329-2017 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
October 14, 2017
Implementation date
September 1, 2018
Scope
GB/T 34329-2017 is the English-translated version of 纤维增强塑料压力容器通用要求.
GB/T 34329-2017 is the Chinese standard "General requirements of fiber reinforced plastics pressure vessel".
Its scope clause reads: This standard specifies the terms and definitions of fiber-reinforced plastic pressure vessels, classification and marking, materials, design, manufacture, quality requirements and inspection Inspection, marking, packaging, transportation and storage, factory information and so on.
This standard applies to the inner diameter of less than or equal to 4800mm, design pressure 0.1MPa ~ 1.6MPa, design temperature of -54 °C ~ 120 °C, the design pressure and the inner diameter of the product is less than or equal to 2.40MPa · m fixed fiber reinforced plastic pressure vessel (hereinafter referred to as pressure Force container).
This standard does not apply to the following pressure vessels. a) Mobile pressure vessels, gas cylinders, oxygen tanks; b) The normal operation of the working pressure is less than 0.1MPa containers (including the feed or discharge process needs instantaneous pressure greater than Or a container equal to 0.1 MPa); c) Pressure vessels containing extremely toxic or highly toxic media or liquefied gases.
Found what you need?
Document preview — GB/T 34329-2017
National Standard of the People's Republic of China
- ICS
- 83.120
- Classification
- Q 23
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Preface
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 classification and marking
- 5 material
- 6 design
- 7 made
- 8 quality inspection and requirements
- 9 logo, packaging, transportation and storage
- Appendix A (Normative) Analysis and Design Method (Discontinuous Analysis)
- Appendix B (Informative) Fiber-reinforced plastic pressure vessel technology assessment
- Appendix C (Normative) Thermoplastic lining and structural layer interface shear strength test method
- Appendix D (Informative) Fiber reinforced plastics pressure vessels Acoustic emission detection methods
1 Scope
This standard specifies the terms and definitions of fiber-reinforced plastic pressure vessels, classification and marking, materials, design, manufacture, quality requirements and inspection
Inspection, marking, packaging, transportation and storage, factory information and so on.
This standard applies to the inner diameter of less than or equal to 4800mm, design pressure 0.1MPa ~ 1.6MPa, design temperature of -54 °C ~
120 °C, the design pressure and the inner diameter of the product is less than or equal to 2.40MPa · m fixed fiber reinforced plastic pressure vessel (hereinafter referred to as pressure
Force container).
This standard does not apply to the following pressure vessels.
a) Mobile pressure vessels, gas cylinders, oxygen tanks;
b) The normal operation of the working pressure is less than 0.1MPa containers (including the feed or discharge process needs instantaneous pressure greater than
Or a container equal to 0.1 MPa);
c) Pressure vessels containing extremely toxic or highly toxic media or liquefied gases.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version applies to this article
Pieces. For undated references, the latest edition (including all amendments) applies to this document.
Pressure vessels Part 1 GB/T 150.1 General requirements
Pressure vessels - Part 4. Manufacture, inspection and acceptance
GB/T 1446 fiber-reinforced plastics performance test methods General
Test method for tensile properties of GB/T 1447 fiber reinforced plastics
Standard Test Method for Compressive Properties of GB/T 1448 Fiber Reinforced Plastics
Test method for bending properties of GB/T 1449 fiber reinforced plastics
GB/T 1450.1 Fiber reinforced plastics - Determination of interlaminar shear strength
GB/T 1634.2-2004 Determination of plastic deformation temperature of the load - Part 2. Plastic, hard rubber and long fiber reinforced composite material
GB/T 2577 glass fiber reinforced plastic resin content test methods
GB/T 3854 reinforced plastic Barcol hardness test method
Test method for chemical resistant properties of glass fiber reinforced thermosetting plastics GB/T GB/T 3961 fiber-reinforced plastic terminology
Liquid unsaturated polyester resin for GB/T 8237 fiber reinforced plastics
GB/T 13657 bisphenol A epoxy resin
GB/T 17470 fiberglass chopped strand mat and continuous strand mat
GB/T 18369 glass fiber rovings
GB/T 18370 glass fiber roving cloth
GB/T 22789.1 rigid PVC sheet classification, size and performance - Part 1. Thickness of 1mm above the plate
GB 50009 Building structural load specifications
HG/T 4090 plastic lining equipment EDM test methods […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 48 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 34329-2017
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 34329-2017
$770.00