Valid

GB/T 33771-2017Sound system equipment -- Electro-acoustical transducers -- Measurement of suspension parts (English PDF)

声系统设备 电声换能器 悬置部件的测量

Preview PDF

This is a limited preview

Buy now to download the full PDF (16 pages)

Need quotation for your management?

Get a formal quotation for GB/T 33771-2017 in 30 minutes.

Issued by

General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China

Level / Type

National · Recommended

Issue date

May 31, 2017

Implementation date

December 1, 2017

Scope

GB/T 33771-2017 is the English-translated version of 声系统设备 电声换能器 悬置部件的测量.

GB/T 33771-2017 specifies how the suspension parts of an electroacoustic transducer, the spider, the surround, the diaphragm or the cone, are measured before the transducer is assembled.

It fixes the test conditions, how the part is held while it is measured and how that fixing is reported, and four measurement methods: static, quasi-static, dynamic incremental and full dynamic.

It then defines and gives the measurement of each parameter: static displacement, static stiffness, the lowest resonance frequency of a cone with a folded ring, dynamic stiffness, the power series expansion coefficients of the stiffness, the effective stiffness at peak displacement and the resistance.

Suspension part makers and loudspeaker makers use it so that their results agree. It is a modified adoption of IEC 62459:2010, cites GB/T 12060.1-2017, was issued on 31 May 2017 and has applied since 1 December 2017.

Found what you need?

Document preview — GB/T 33771-2017

National Standard of the People's Republic of China

ICS
33.160.50
Classification
M 70

Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China

Contents

  • Preface
  • 1 Scope
  • 2 normative reference document
  • 3 Terms and definitions
  • 4 Test conditions
  • 5 fixed parts of the suspension
  • 5.1 Overview
  • 5.2 Damage measurement
  • 5.3 Lossless measurement
  • 5.4 Fixed position
  • 5.5 Orientation of internal fixation
  • 5.6 Fixed status report
  • 6 Measuring method
  • 6.1 Static measurement method
  • 6.2 quasi-static measurement method
  • 6.3 Dynamic incremental measurement method
  • 6.4 Full dynamic measurement method
  • 7 static displacement xstatic (Fdc)
  • 7.1 Definitions
  • 7.2 Measurement method
  • 8 static stiffness factor Kstatic (xdc)
  • 8.1 Definitions
  • 8.2 Measurement method
  • 8.3 Measurement results report
  • 9.1 Definitions
  • 9.2 Measurement method
  • 10 Dynamic stiffness factor K (xac)
  • 10.1 Definitions
  • 10.2 Measuring method
  • 11 K (x) of the power series expansion coefficient
  • 11.1 Definitions
  • 11.2 Measurement results report
  • 12 effective stiffness coefficient Keff (xpeak)
  • 12.1 Definitions
  • 12.2 Measurement method
  • 12.3 Measurement results report
  • 13 resistance resistance R
  • 13.1 Definitions
  • 13.3 Measurement results report
  • Reference

Foreword

This standard is drafted in accordance with the rules given in GB/T 1.1-2009.

This standard uses the re-drafting method to modify IEC 62459:2010 "sound system equipment electro-acoustic transducer suspension parts measurement".

The main technical differences between this standard and IEC 62459:2010 are as follows.

--- will 3.6,3.7 in the "note" were moved to the text of 3.6,3.7;

--- modify the contents of 3.11, the "f0 ~ 2pi K (xoff) delta mS "Modified to" f0 ~ 2pi C (xoff) delta mS "(See 3.11);

--- modified the contents of 6.3, will use a certain size of the constant DC signal (such as constant displacement xdc) and small AC signal (Such as displacement xac) aliasing as an excitation source, measuring the steady-state suspension of the AC component response (such as the return force of the AC part Fac "is modified to" use a constant DC signal with a certain size (such as constant force Fdc) and a small AC signal (such as restoring force AC part of the Fac) aliasing as the excitation source, measuring the steady-state suspension of the AC component response (such as displacement xac) "(see 6.3);

--- modified the contents of 6.4, will use a certain size of the AC signal (such as displacement xac) as the excitation source, measuring the suspension components Of the AC response (such as the exchange of response Fac) "modified to" use a certain size of the AC signal (such as AC reply force Fac) As an excitation source, measure the AC response of the suspension (eg displacement xac) "(see 6.4);

--- delete the 7.2.3 "note" footnote;

- modify the contents of 9.1, and amend "(6)" to "(1)" (see 9.1);

--- increase the "use of wide-band sinusoidal signal to measure the displacement amplitude response X (jomega), to find the resonant frequency fR, get the most Good measurement setting parameters (measuring voltage, peak displacement) "(see 10.2.3).

1 Scope

This standard specifies the measurement of the suspension components before the electro-acoustic transducer assembly, such as centering, folding, diaphragm or cone performance of the relevant parameters Number and measurement methods. The measurement results can be used for engineering design and quality control. This standard can improve the manufacturer of the suspension parts and the speaker manufacturer Consistency of measurement results.

This standard applies to the measurement of the suspension components of electroacoustic transducers (eg loudspeakers). Based on the linear model and the nonlinear model of the suspension component, Static measurement method and dynamic measurement method were used to measure the relevant parameters.

2 Normative reference documents

The following documents are indispensable for the application of this document. For dated references, only the dated edition applies to this document. For undated references, the latest edition (including all modifications) applies to this document.

GB/T 12060.1-2017 Sound System Equipment Part 1 Overview (IEC 60268-1:1985, MOD)

3 Terms and definitions

The following terms and definitions apply to this document.

3.1 Suspension parts

A centering piece made of a dipped cloth, or a loop made of rubber, foamed material, paper or cloth.

3.2 Displacement

The distance at which the inner edge of the suspension member moves in the vertical direction.

3.3 Peak displacement

xpeak The peak of displacement at the resonant frequency in the dynamic measurement.

3.4 Driving force

The restoring force, the frictional force and the inertia of the suspension member and its inner edge fixture.

3.5 Transfer function

H (f)

The ratio of the displacement spectrum X (jomega) = FT {x (t)} to the driving force spectrum F (jomega) = FT {F (t)} is defined by the formula (1)

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 16 pages — is available in the English PDF.

Referenced standards

How to Download GB/T 33771-2017

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
16 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 33771-2017

$235.00