GB/T 33769-2017Sound system equipment -- Electro-acoustical transducers -- Measurement of large signal parameters (English PDF)
声系统设备 电声换能器 大信号参数的测量
This is a limited preview
Buy now to download the full PDF (21 pages)
Need quotation for your management?
Get a formal quotation for GB/T 33769-2017 in 30 minutes.
Issued by
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Level / Type
National · Recommended
Issue date
May 31, 2017
Implementation date
December 1, 2017
Scope
GB/T 33769-2017 is the English-translated version of 声系统设备 电声换能器 大信号参数的测量.
GB/T 33769-2017 is the identical translation of IEC 62458:2010 and measures the large signal parameters of electro-acoustical transducers.
It defines the terms and parameters of the large signal lumped parameter model, then fixes the measurement signals - large DC, large DC with small AC, broadband noise and music - the mounting conditions for loudspeaker units and systems, the climatic conditions, the acoustic environment and the preconditioning.
The measuring methods run from static and quasi-static to point by point dynamic and fully dynamic.
The parameters measured are the force factor Bl(x) with its limiting displacement, symmetry point and voice coil offset, the non-linear stiffness Kms(x), the displacement and current dependent inductance, and the maximum peak displacement derived from geometry.
It cites GB/T 12060.5-2011 and IEC 60268-1. Issued on 31 May 2017, it has applied since 1 December 2017.
Found what you need?
Document preview — GB/T 33769-2017
National Standard of the People's Republic of China
- ICS
- 33.160.50
- Classification
- M 70
Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Contents
- Preface
- 1 Scope
- 2 normative reference document
- 3 Terms and definitions
- 4 measurement signal
- 4.1 Overview
- 4.2 Large DC signal
- 4.3 large DC signal and small AC signal
- 4.4 Broadband noise signal
- 4.5 music signal
- 5 installation conditions
- 5.1 Speaker unit
- 5.2 Speaker system
- 6 Climatic conditions
- 7 Acoustic environment
- 9 Time varying characteristics of the loudspeaker
- 10.1 Overview
- 10.2 Static measurement method or quasi-static measurement method
- 10.3 point by point dynamic measurement method
- 11 nonlinear electromechanical coupling factor
- 11.1 Force Coupling Factor Curve Bl (x)
- 11.2 Force Coupling Factor Defined Displacement xBl
- 11.3 Symmetry point xsym (xac)
- 11.4 voice coil offset xoffset
- 12 nonlinear stiffness factor
- 12.1 Nonlinear stiffness coefficient curve Kms (x)
- 12.2 Steady displacement xC
- 12.3 The degree of asymmetry of the stiffness coefficient AK (xpeak)
- 13 displacement related inductance Le (x)
- 13.1 Inductance curve Le (x)
- 13.2 Inductive limited displacement xL
- 14 Current-dependent inductance Le (i)
- 14.1 Definitions
- 15 Parameters derived from geometry and performance
- 15.1 Maximum peak displacement xMAXd
- 15.2 Measuring method
- Reference
Foreword
This standard is drafted in accordance with the rules given in GB/T 1.1-2009.
This standard uses the translation method equivalent to IEC 62458:2010 "sound system equipment electroacoustic transducer large signal parameter measurement".
This standard has made the following editorial changes.
Figure 2, Figure 3 and Figure 4 add "Note: The sensor includes a mechanical sensor or an acoustic sensor".
1 Scope
This standard specifies the basic terms and parameters of the large signal lumped parameter model of electroacoustic transducers, the measurement method and the report of the measurement results form.
This standard applies to transducers such as loudspeaker units, loudspeaker systems, headphones, microphones, vibrators and other A dynamic or electromagnetic actuator is coupled to a mechanical suspension system.
2 Normative reference documents
The following documents are indispensable for the application of this document. For dated references, only the dated edition applies to this document. For undated references, the latest edition (including all modifications) applies to this document.
GB/T 12060.5-2011 Acoustic system equipment - Part 5: Test methods for main performance of loudspeakers (IEC 60268-5:2007, IDT)
IEC 60268-1 Sound System Equipment Part 1: Overview (Soundsystemequipment-Part 1. General)
3 Terms and definitions
The following terms and definitions apply to this document.
3.1 Electro-mechanical equivalent circuit
The analogy between electricity and force is expressed by the circuit in order to apply the circuit theory to solve the problem of vibration and sound. Figure 1 shows the electric The equivalent circuit diagram of the electro - hydraulic analogue of the transducer.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 21 pages — is available in the English PDF.
Referenced standards
Normative references
IEC 60268-1
How to Download GB/T 33769-2017
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 12060.5-2011 — Sound system equipment -- Part 5: Methods of measurement for main characteristics of loudspeakers
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 33769-2017
$295.00