Valid

GB/T 33636-2023Pneumatic fluid power - Push-in connectors for thermoplastic tubes (English PDF)

Preview PDF

This is a limited preview

Buy now to download the full PDF (61 pages)

Need quotation for your management?

Get a formal quotation for GB/T 33636-2023 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

May 23, 2023

Implementation date

May 23, 2023

Scope

GB/T 33636-2023 (Pneumatic fluid power - Push-in connectors for thermoplastic tubes) is available as an English-translated PDF.

GB/T 33636-2023 is the Chinese standard "Pneumatic fluid power - Push-in connectors for thermoplastic tubes".

Its scope clause reads: This document specifies the design of plug-in pipe joints used for thermoplastic pipes with an outer diameter of 3 mm to 16 mm (hereinafter referred to as plastic pipes): General requirements and test methods for design and performance: The test methods in this document apply to plug-in fitting assemblies used in pneumatic systems: This document does not apply to air brake systems:. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 33636-2023

National Standard of the People's Republic of China

ICS: 23.100.40
Classification: J 20
Replacing: GB/T 33636-2017

Issued by: State Administration for Market Regulation, China National Standardization Administration

Preface
Introduction
1 Scope
2 Normative references
3 Terms and Definitions
4 Working conditions
5 Structural features
6 Tube outer diameter
7 design
8 logo
9 Performance requirements and tests
10 Mark
11 Labeling instructions
Appendix A (Normative) PA pipes for testing
Appendix B (Normative) PU tube for testing

1 Scope

This document specifies the design of plug-in pipe joints used for thermoplastic pipes with an outer diameter of 3 mm to 16 mm (hereinafter referred to as plastic pipes):

General requirements and test methods for design and performance:

The test methods in this document apply to plug-in fitting assemblies used in pneumatic systems: This document does not apply to air brake systems:

2 Normative references

The contents of the following documents constitute the essential provisions of this document through normative references in the text: Among them, dated references

For documents, only the version corresponding to the date is applicable to this document; for undated reference documents, the latest version (including all amendments) is applicable to this document:

Note: GB/T 7306:1-2000 55° sealing pipe thread Part 1: Cylindrical internal thread and conical external thread (eqvISO 7-1:1994)

GB/T 7306:2-2000 55°Sealing Pipe Threads Part 2: Conical Internal Thread and Conical External Thread (eqvISO 7-1:1994)

ISO 4759-1 Tolerances of fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C (Tolerances

Note: GB/T 3103:1-2002 Fastener tolerance bolts, screws, studs and nuts (idtISO 4759-1:2000)

Note: GB/T 17446-2012 Fluid Power System and Component Vocabulary (ISO 5598:2008, IDT)

ISO 8573-1:2010 Compressed air Part 1: Pollutants and purification levels (Compressedair-Part 1:Contami-

Note: GB/T 13277:1-2008 Compressed air Part 1: Pollutant purification level (ISO 8573-1:2001, MOD)

ISO 10619-1 Rubber and plastic hoses and unreinforced hoses - Measurement of flexibility and stiffness - Part 1: Bend test at room temperature

Note: GB/T 5565:1-2017 Measurement of flexibility and stiffness of rubber and plastic hoses and non-reinforced hoses Part 1: Bending test at room temperature (ISO 10619-1:2011, IDT) ends)

Note: GB/T 14038-2008 pneumatic connection port and stud end (ISO 16030:2001/Amd:1:2005, IDT) and UNRThreadForm)]

3 Terms and Definitions

The terms and definitions defined in ISO 5598 apply to this document:

ISO and IEC maintain terminology databases for standardization at:

GB/T 40565.4 | GB/T 40565.3 | GB/T 40565.2 | GB/T 33626.2 | GB/T 33626.1 | […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 61 pages — is available in the English PDF.

Referenced standards

Normative references

GB/T 7306 · ISO 4759 · GB/T 3103 · ISO 5598 · ISO 8573 · GB/T 13277 · ISO 10619 · ISO 16030

How to Download GB/T 33636-2023

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.