GB/T 32026-2015Silver coated glass mirror - Environmental test methods (English PDF)
镀银玻璃镜 耐环境腐蚀的测试方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 32026-2015 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
September 11, 2015
Implementation date
April 1, 2016
Scope
GB/T 32026-2015 is the English-translated version of 镀银玻璃镜 耐环境腐蚀的测试方法.
GB/T 32026-2015 is the Chinese standard "Silver coated glass mirror - Environmental test methods". Its scope clause reads: This standard specifies the silvered glass mirror neutral salt spray test (NSS test), copper accelerated acetic acid salt spray test (CASS test) and condensate Water testing equipment, reagents and methods.
This standard also specifies the evaluation of salt spray corrosion box method. This standard applies to silvered glass mirrors resistance to environmental corrosion test. Its clauses include test solution.
Found what you need?
Document preview — GB/T 32026-2015
National Standard of the People's Republic of China
- ICS
- 19.040
- Classification
- Y 89
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 test solution
- 3.1 Requirements agent
1 Scope
This standard specifies the silvered glass mirror neutral salt spray test (NSS test), copper accelerated acetic acid salt spray test (CASS test) and condensate
Water testing equipment, reagents and methods.
This standard also specifies the evaluation of salt spray corrosion box method.
This standard applies to silvered glass mirrors resistance to environmental corrosion test.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 5213 cold-rolled carbon steel sheet and strip
Corrosion GB/T 16545-1996 removal of metals and alloys after corrosion test the corrosion products of the metal sample
3 test solution
3.1 Requirements agent
3.1.1 Deionized water
The water should be formulated in solution in deionized water, conductivity at 25 °C ± 3 °C time should be less than 20µs/cm.
3.1.2 Sodium chloride
3.1.2.1
should be of analytical grade or analytical grade purity above the level of sodium chloride.
3.1.2.2
sodium chloride content of copper should be less than 0.001% (mass fraction), the nickel content should be less than 0.001% (mass fraction). Copper and
Nickel content by the atomic absorption spectrophotometry or other analytical methods with the same accuracy of measurement.
3.1.2.3
The content of sodium chloride, sodium iodide should be less than 0.1% (mass fraction), the total impurity content should be less than 0.5% (mass fraction).
Still beyond the range 6.0 to 7.0, you should check whether there is water, sodium chloride or other impurities.
3.1.3 Other reagents
Other reagents were of analytical grade purity or above the level of analytical reagent should be used.
Preparation of the test solution 3.2 NSS 3.2.1 sodium chloride solution preparation
At a temperature of 25 °C ± 3 °C environment, the sodium chloride is dissolved in water to prepare an initial concentration of 50g/L ± 5g/L sodium chloride
Solution.
3.2.2 sodium chloride solution, initial concentration and initial pH value adjustment
3.2.2.1 General requirements
Adjust the initial concentration of sodium chloride solution and the initial pH value of the spray solution of sodium chloride salt spray chamber to collect concentration and pH and Regulation […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 32026-2015
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 32026-2015
$205.00