Valid

GB/T 31228-2014Instrumented nanoindentation test—Terminology (English PDF)

仪器化纳米压入试验 术语

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 31228-2014 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

September 30, 2014

Implementation date

April 15, 2015

Scope

GB/T 31228-2014 is the English-translated version of 仪器化纳米压入试验 术语.

GB/T 31228-2014 defines the common terms and their definitions used in instrumented nanoindentation testing, grouped by universal basis, instrument characteristics, mechanical measurement, parameter identification, test specimens and test setup.

Clause 1 states that it applies to the instrumented nanoindentation test and can also be extended to the instrumented indentation test; no exclusion is stated.

The contents follow the same order, with clause 2 on the universal basis, clause 3 on instrument characteristics, clause 4 on mechanical measurement, clause 5 on parameter identification, clause 6 on test samples and clause 7 on test setup, closing with a reference list and an index.

Clause 2 defines the instrumented indentation test, in which a selected indenter is driven into the specimen, the applied load and the depth in the sample are measured automatically, and the hardness and mechanical parameters of the material are calculated from a mechanical model; its notes record the division made in ISO 14577 into a macro range of 2 N to 30 kN, a micro range below 2 N with depth above 0.2 µm, and a nano range at depth of 0.2 µm or less.

The same clause defines the instrumented indentation tester, the nanoindentation tester, whose load range is usually no more than 500 mN, and the indenter, with notes on its two-part construction, on the effect of deviation of the tip geometry from its design shape on test results, and on the classification of indenters by tip geometry.

The introduction describes instrumented nanoindentation as a micro and nanomechanical test technique developed over the previous two decades and used in materials science, physics, biology, mechanics and industrial production, and states that standardizing its terms helps understanding, communication and the promotion and application of the technique.

The standard was proposed by the Chinese Academy of Sciences and is administered by the national standardization technical committee of nanotechnology (SAC/TC279); the page places it at ICS 19.060 and Chinese classification A42.

The frontispiece gives 30 September 2014 as the date of issue, and the standard has applied since 15 April 2015.

Found what you need?

Document preview — GB/T 31228-2014

National Standard of the People's Republic of China

ICS
19.060
Classification
A 42

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Preface
  • Introduction
  • 1 Scope
  • 2 Universal 1 basis
  • 3 instrument characteristics Mechanical measuring 4
  • 6 Test Sample
  • 8 7 Test Setup
  • Reference
  • Index

Foreword

This standard was drafted in accordance with GB/T 1.1-2009 given rules.

Introduction

Instrumented nano-indentation test is a micro/nanomechanical test technology developed in the past two decades. The technology has since its birth, has Disciplines widely used in materials science, physics, biology, mechanics and industrial production is becoming a micro/nanomechanical test technology One of the important means.

Specification instrumented nanoindentation techniques involved in the terms and their definitions, help to enhance the understanding and communication technology to promote the Promotion and application of technology, to make it better for scientific research, production and trade in services.

1 Scope

This standard defines the instrumented nanoindentation test on the basis of universal, instrument characteristics, mechanical measurement, parameter identification, test specimens, test equipment Fixed aspect involved in common terms and their definitions.

This standard applies to instrumented nanoindentation test can also be widened to instrumented indentation test.

2 Universal base

2.1 Instrumented indentation test

Drive selected indenter into the specimen, load and automatically measure the applied pressure in the sample depth, calculated based on the mechanical model of the timber Hardness and mechanical parameters of the test material.

Note 1. Instrumented indentation test focuses on the course of action, similar to the tension, compression, bending, torsion testing; and hardness measurement focuses pushed after unloading residues Size left indentation, often called indentation.

Note 2. The international standard ISO 14577 and press-fit load F depth h, the test is divided into. a macroscopic scale (macrorange), 2N<=F<=30kN; microstructure Range (microrange), F < 2N, h> 0.2µm; nanometer range (nanorange), h<=0.2µm.

Note 3. The instrument load range is usually no more than 500mN, corresponding indentation depth in nanometers to several micrometers, used to call the nanoindentation (Nanoindentationtest). At present, we tend to adopt the international standard ISO 14577 naming, multi-called instrumented indentation test.

2.2 Indentor

Through direct and indirect calibration inspection, it is possible to achieve Instrumented indentation test instruments.

Note 1. The instrument does not belong to the traditional pressed into the hardness category. Traditional durometer hardness only measure, and pressed into the measured hardness tester can not only, but also measuring the elastic modulus Amount and other mechanical parameters.

Note 2. The instrument is pressed into the material testing machine belonging to the category. Traditional materials testing machine for whole-destructive test specimens, and pressed into the micro-sample instrument for micro-damage Type test.

2.3 Nanoindentation instrument

Indentation depth is usually in the order of a few microns to nanometers, load and displacement measurements are generally superior resolution and 10-1nm amount 101nN Indentation level meter.

Note 1. Currently, such instruments to electromagnetic or electrostatic driven mainly typical range is 500mN or 10mN.

2.4 Indenter

Indentor for pressed into the specimen and having a specific geometric shape and size of the parts.

Note 1. The head is usually composed of two parts. Often used in front of the diamond, sapphire, tungsten carbide and other materials, ground into a fine tip required predetermined geometric Shape and size, for pressing into the sample; rear often used steel materials, processed into a predetermined shape of the base plate for fixing the front head portion and the connecting device Control lever.

Note 2. Factors nanoindentation test results, compression tip of geometry deviation from the shape of its design, as well as determining the shape of the error, etc. influences.

Note 3. The actual use, usually based on the design of the indenter tip geometry classification, including Vickers indenter, Bolivia's head, cube corner indenter, and conical indenter Spherical pressure class.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 31228-2014

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 31228-2014

$235.00