GB/T 3094-2012Cold drawn shaped steel tubes (English PDF)
冷拔异型钢管
This is a limited preview
Buy now to download the full PDF (32 pages)
Need quotation for your management?
Get a formal quotation for GB/T 3094-2012 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
May 11, 2012
Implementation date
February 1, 2013
Scope
GB/T 3094-2012 is the English-translated version of 冷拔异型钢管.
GB/T 3094-2012 is the Chinese standard "Cold drawn shaped steel tubes". Its scope clause reads: This Standard specifies the classification, designation, ordering information, shape, dimension, technical requirements, test method, inspection rule, packaging, marking and quality certificate of cold drawn shaped steel tubes.
This Standard is applicable to cold-drawn simple-section shaped tube (hereinafter referred to as steel tube). Its clauses include classification and designation; ordering information; shape, dimension and weight; technical requirements; test methods; inspection rules; packaging, marking and quality certificate.
It was issued by the General Administration of Quality Supervision, Inspection and Quarantine (AQSIQ) on MAY 11, 2012 and took effect on FEBRUARY 1, 2013.
Found what you need?
Document preview — GB/T 3094-2012
National Standard of the People's Republic of China
- ICS
- 77.140.75
- Classification
- H 48
- Replacing
- GB/T 3094-2000
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword3
- 1 Scope4
- 2 Normative References4
- 3 Classification and Designation6
- 4 Ordering Information6
- 5 Shape, Dimension and Weight7
- 6 Technical Requirements9
- 7 Test Methods12
- 8 Inspection Rules13
- 9 Packaging, Marking and Quality Certificate13
- Appendix A (Normative) Shape and Dimension of Steel Tube14
- Appendix B (Normative) Determination Method for Twist Value of Shaped Steel Tube32
1 Scope
This Standard specifies the classification, designation, ordering information, shape, dimension, technical requirements, test method, inspection rule, packaging, marking and quality certificate of cold drawn shaped steel tubes.
This Standard is applicable to cold-drawn simple-section shaped tube (hereinafter referred to as steel tube).
2 Normative References
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the normative document (including any amendments) applies.
GB/T 222 Permissible Tolerances for Chemical Composition of Steel Products
GB/T 223.5 Steel and Iron - Determination of Acid-soluble Silicon and Total Silicon Content - Reduced Molybdosilicate Spectrophotometric Method
GB/T 223.9 Iron, Steel and Alloy - Determination of Aluminum Content - Chrom Azurol S Photometric Method
GB/T 223.12 GB/T 223.62 Methods for Chemical Analysis of Iron, Steel and Alloy - The Sodium Carbonate Separation - Diphenyl Carbazide Photometric Method for the Determination of Chromium Content
GB/T 223.14 Methods for Chemical Analysis of Iron, Steel and Alloy - The N-benzoy-N-phenylhydroxylamine Extraction Photometric Method for the Determination of Vanadium Content
GB/T 223.17 Methods for Chemical Analysis of Iron, Steel and Alloy - The Diantipyrylmethane Photometric Method for the Determination of Titanium Content
3 Classification and Designation
Classification and designation of steel tubes according to section shape are as follows. […]
4 Ordering Information
The contract or order for ordering steel tubes according to this Standard shall include but not limited to the following contents. […]
5 Shape, Dimension and Weight
5.1 Shape and dimension
The shape and dimension of steel tube shall respectively meet the requirements of Figures A.1~A.6 and Tables A.1~A.6 in Appendix A. As negotiated by the supplier and the purchaser, steel tube with shape and/or size beyond those specified in Figures A.1~A.6 and Tables A.1~A.6 in Appendix A may be supplied.
5.3 Side unevenness
Side unevenness of steel tube shall meet those specified in Table 2.
5.4 Radius of outside corner
The radius (R) of each outside corner of the section shall meet those specified in Table 3.
5.5 Curvature
Curvature of steel tube shall meet those specified in Table 4.
When the curvature grade of steel tube is not indicated in the contract by the purchaser, it shall meet the requirements of ordinary grade precision. The high grade dimensional precision, when required by the purchaser, shall be indicated in the contract.
5.6 Twist value
The steel tube shall be free from visible twist. The twist values of square steel tube, rectangle steel tube and rectangular trapezoid steel tube shall meet those specified in Table 5.
5.7 Length
5.7.1 General length
The general length of steel tube is 2000~9000mm.
As required by the purchaser, steel tube with length beyond those specified may be supplied upon negotiation between the supplier and the purchaser and when indicated in the contract.
5.7.2 Specified length and multiple length
5.8 End shape
End faces on both ends of steel tube shall be vertical to the axis of steel tube, and the burr on notch shall be removed.
5.9 Weight
The steel tube is delivered according to actual weight. When indicated in the contract, it may also be delivered according to the theoretical weight. See Appendix A for the calculation formula of theoretical weight (with steel density of 7.85 kg/dm³).
6 Technical Requirements
6.1 Designation and chemical composition of steel
6.1.1 For quality carbon structural steels with designations of 10, 20, 35 and 45, the […]
6.2 Manufacturing method
6.2.1 Steel tube shall be manufactured of seamless steel tube through cold-drawn forming.
6.2.2 As required by the purchaser, steel tube may be manufactured of welded steel tube through cold-drawn forming upon negotiation between the supplier and the purchaser and when indicated in the contract. The weld of cold-drawn welded steel tube shall be kept away from round corner.
6.3 Delivery state
The steel tube shall be delivered in cold-drawn state. As required by the purchaser, the steel tube may be delivered in heat treatment state upon negotiation between the supplier and the purchaser and when indicated in the contract.
6.4 Mechanical performance
6.4.3 For structural alloy steel tube with perimeter not less than 240mm and wall thickness not less than 10mm, the impact absorbed energy of standard specimen shall meet the requirements of GB/T 3077.
6.4.4 The sampling position for mechanical performance test of cold-drawn welded steel tube shall be within the base material area.
6.5 Surface quality
6.5.1 The internal and external surfaces of steel tube shall be free from crack, fold, scab, creasing and delamination. These defects shall be completely removed with removed depth not exceed the negative deviation of nominal wall thickness. The actual wall thickness of the removal point shall not be less than the permissible minimum deviation of the wall thickness.
6.5.2 Other local defects not exceed the negative deviation of wall thickness are permissible.
6.5.4 Cold-drawn welded steel tube shall be free from lap welding and over-burning.
The outer burr of steel tube weld shall be cleared with residual height not greater than 0.5mm; inner burr of steel tube weld is permissible. As required by the purchaser, the inner burr may be specially specified upon negotiation between the supplier and the purchaser and when indicated in the contract.
7 Test Methods
7.1 The dimension and shape of steel tube shall be measured piece by piece with measuring instrument of required precision. The measurement method of twist value shall meet the requirements of Appendix B.
7.2 Internal and external surfaces of steel tube shall be visually inspected piece by piece under sufficient lighting condition.
7.3 Sampling method and test method for other inspection items of steel tube shall meet those specified in Table 8.
8 Inspection Rules
8.1 Inspection and acceptance
Inspection and acceptance of steel tube are carried out by the supplier's quality-technical supervision department.
8.2 Batching rules
8.2.1 Inspection and acceptance are carried out for steel tubes according to batches.
8.2.2 Each batch shall be composed of steel tubes of the same designation, furnace
8.4 Re-inspection and judgment rules
9 Packaging, Marking and Quality Certificate
Packaging and quality certificate of steel tube shall meet the requirements of GB/T 2102. […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 32 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 222Steels and alloys - Permissible deviations of product analyzed chemical composition
- GB/T 223.5Steel and iron -- Determination of acid-soluble silicon and total silicon content -- Reduced molybdosilicate spectrophotometric method
- GB/T 223.9Iron, steel and alloy -- Determination of aluminium content -- Chrome azurol S photometric method
- GB/T 223.12Methods for chemical analysis of iron, steel and alloy. The sodium carbonate separation-diphenyl carbazide photometric method for the determination of chromium content
- GB/T 223.14Methods for chemical analysis of iron, steel and alloy. The N-benzoyl-N-phenylhydroxylamine extraction photometric method for the determination of vanadium content
- GB/T 223.17Methods for chemical analysis of iron, steel and alloy - The diantipyrylmethane photometric method for the determination of titanium content
Similar standards
Editions of GB/T 3094
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 3094-2012 | Cold drawn shaped steel tubes | current edition | Current |
| GB/T 3094-2000 | Cold drawn shaped steel tubes | previous edition | Superseded |
This page sells the current edition, GB/T 3094-2012. Earlier editions are listed for reference only.
How to Download GB/T 3094-2012
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 222-1984 — Method of sampling steel for determination of chemical composition and permissible variations for product analysis
GB/T 222-2006 — Permissible tolerances for chemical composition of steel products
GB/T 222-2025 — Steels and alloys - Permissible deviations of product analyzed chemical composition
GB/T 3094-2012
$75.00