GB/T 30063-2013Longitudinal submerged arc welded steel tubes for structural purpose (English PDF)
结构用直缝埋弧焊接钢管
This is a limited preview
Buy now to download the full PDF (18 pages)
Need quotation for your management?
Get a formal quotation for GB/T 30063-2013 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 17, 2013
Implementation date
September 1, 2014
Scope
GB/T 30063-2013 is the English-translated version of 结构用直缝埋弧焊接钢管.
GB/T 30063-2013 is the Chinese standard "Longitudinal submerged arc welded steel tubes for structural purpose".
Its scope clause reads: This standard specifies the dimensions, shape, weight, technical requirements, test methods, inspection rules, markings, packaging and quality certificates for longitudinal submerged arc welded steel tubes for structural purpose.
This standard is applicable to longitudinal submerged arc welded steel tubes, which have an outer diameter not less than 400 mm, for buildings, bridges, towers, piles, struts and other general structures (hereinafter referred to as "steel tubes").
It is not applicable to steel tubes for mechanical structures. Its clauses include ordering content; dimension, shape, weight and allowable deviations; technical requirements; test methods; inspection rules; packaging, marking and quality certificate.
It was issued by the General Administration of Quality Supervision, Inspection and Quarantine on DECEMBER 17, 2013 and took effect on SEPTEMBER 01, 2014.
Found what you need?
Document preview — GB/T 30063-2013
National Standard of the People's Republic of China
- ICS
- 77.140.75
- Classification
- H 48
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword3
- 1 Scope4
- 2 Normative references4
- 3 Ordering content6
- 4 Dimension, shape, weight and allowable deviations7
- 5 Technical requirements11
- 6 Test methods17
- 7 Inspection rules18
- 8 Packaging, marking and quality certificate18
Foreword
This standard is drafted in accordance with the rules given in GB/T 1.1-2009.
This standard refers to ASTM A500-2010 "Specification for cold-formed welded and seamless carbon steel structural tubing in rounds and shapes" and JIS G 3444-2010 "Carbon steel tubes for general structure".
1 Scope
This standard specifies the dimensions, shape, weight, technical requirements, test methods, inspection rules, markings, packaging and quality certificates for longitudinal submerged arc welded steel tubes for structural purpose.
This standard is applicable to longitudinal submerged arc welded steel tubes, which have an outer diameter not less than 400 mm, for buildings, bridges, towers, piles, struts and other general structures (hereinafter referred to as "steel tubes"). It is not applicable to steel tubes for mechanical structures.
2 Normative references
The following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this standard.
GB/T 222 Permissible tolerances for chemical composition of steel products
GB/T 223.5 Steel and iron - Determination of acid-soluble silicon and total silicon content - Reduced molybdosilicate spectrophotometric method
GB/T 223.9 Iron steel and alloy - Determination of aluminum content - Chrom-azurol S photometric method
GB/T 223.12 Methods for chemical analysis of iron, steel and alloy - The sodium carbonate separation-diphenyl carbazide photometric method for the determination of chromium content
3 Ordering content
3.1 Contracts or orders for ordering steel tubes in accordance with this standard shall include the following.
3.2 As determined by the supplier and the purchaser through negotiation, and indicated in the contract, the purchaser may choose the following supplementary requirements.
4 Dimension, shape, weight and allowable deviations
4.1 Dimension
4.1.1 Outer diameter and wall thickness
The nominal outer diameter D and the nominal wall thickness S of the steel tube shall comply with the requirements of Table 1. According to the requirements of the purchaser, through negotiation between the supplier and the purchaser, it may supply the steel tubes of other dimensions than those listed in Table 1.
4.1.2 Allowable deviation of outer diameter and wall thickness
The allowable deviation of outer diameter and wall thickness of the steel tube shall comply with the requirements of Table 2 and Table 3, respectively.
4.2 Difference of tube diameter
4.7 Weight
4.7.1 Steel tubes are delivered according to theoretical weight. Through negotiation between the supplier and the purchaser, and as indicated in the Tube's end contract, it may also be delivered according to the actual weight.
4.7.2 The allowable deviation of the actual weight and theoretical weight of each batch or single steel tube shall be.
4.7.3 The theoretical weight of the steel tube is calculated according to formula (1).
5 Technical requirements
5.1 Steel designation and chemical composition
5.1.1 The designation and chemical composition of the steel (melting analysis) shall comply with the provisions for Q235B, Q235C in GB/T 700, Q345B, Q345C, Q390B, Q390C, Q420B, Q420C, Q460C, Q460D in GB/T 1591 or Q235GJC, Q345GJB, Q345GJC, Q390GJB, Q390GJC, Q420GJC in GB/T 19879, respectively.
5.2 Manufacturing process
Steel tubes shall be manufactured by double-sided longitudinal submerged arc welding. The girth weld of butt-welded steel tube can be manufactured by manual low-hydrogen electrode arc welding, submerged arc automatic welding, automatic or semi-automatic fusion welding, and gas-shielded arc welding.
5.3 Delivery status
Steel tubes shall be delivered in welded status. According to the requirements of the purchaser, through negotiation between the supplier and the purchaser, and as indicated in the contract, the steel tube may be delivered in the overall heat treatment status.
5.4 Mechanical properties
5.4.4 Charpy V-notch impact test
According to the requirements of the purchaser, through negotiation between the supplier and the purchaser, and as indicated in the contract, the steel tube may be subjected to the longitudinal Charpy V-notch impact test of the base metal. The impact absorbed energy of steel tube of each designation shall meet the requirements of Table 4 and Table 5, respectively.
5.5 Process performance
5.5.1 Guided bending test
For the steel tubes with a wall thickness of less than 10 mm, it shall respectively take 1 face bending specimen and 1 back bending specimen to perform the guided bending test. The specimen shall be cut from the vertical weld on the steel tube. The weld is located in the middle of the specimen.
5.6 Macro inspection
For the submerged arc welded steel tube, it shall use the 10% ammonium persulfate solution or a 4% nitric acid alcohol solution to perform the acid etching inspection of the weld's cross-section. After the test, the welds inside and outside the specimen shall be completely penetrated, it is not allowed to have non-penetration, non-fusion or cracking.
5.7 Non-destructive testing
According to the requirements of the purchaser, through negotiation between the supplier and the purchaser, as indicated in the contract, it may perform the ultrasonic testing or radiation testing against each weld (including butt-jointed circumferential weld).
5.8 Appearance quality
5.8.1 Surface defects
The inner and outer surfaces of the steel tube shall be smooth, it is not allowed to have folding, cracks, cold-lap, weld bead and ogival base defects (such as scratches). These defects and ogival base defects shall be completely removed, the remaining wall thickness at the defect removal shall be no less than the minimum value as allowed by the wall thickness.
5.10 Repair of defects
For the steel tube's weld defects and base metal defect which has a depth not more than 1/3 of base metal's thickness, it may be subjected to weld repair by the use of manual low-hydrogen electrode arc welding, submerged arc automatic welding, automatic or semi-automatic consumable electrode gas shielded arc welding. Prior to repair, the defects shall be cleaned to meet the welding requirements.
6 Test methods
6.1 The dimension and shape of the steel tube shall be measured one by one using a gage that meets the accuracy requirements.
6.2 The inner and outer surfaces of steel tubes shall be inspected visually under full lighting conditions.
6.3 Sampling methods and test methods for other inspection items of steel tubes shall comply with the requirements of Table 7.
7 Inspection rules
7.1 Inspection and acceptance
The inspection and acceptance of steel tubes shall be carried out by the supplier's quality technical supervision and inspection department.
7.2 Group-batch rule
Steel tubes shall be inspected and accepted in batches. Each batch shall consist of steel tubes of the same heat number, the same designation, the same specification, the same welding procedure, and the same heat treatment system (if applicable). The number of steel tubes per batch shall not exceed 100.
8 Packaging, marking and quality certificate
The packaging, marking and quality certificate of steel tubes shall comply with the provisions of GB/T 2102. […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 18 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 222Steels and alloys - Permissible deviations of product analyzed chemical composition
- GB/T 223.5Steel and iron -- Determination of acid-soluble silicon and total silicon content -- Reduced molybdosilicate spectrophotometric method
- GB/T 223.9Iron, steel and alloy -- Determination of aluminium content -- Chrome azurol S photometric method
- GB/T 223.12Methods for chemical analysis of iron, steel and alloy. The sodium carbonate separation-diphenyl carbazide photometric method for the determination of chromium content
Similar standards
How to Download GB/T 30063-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 222-1984 — Method of sampling steel for determination of chemical composition and permissible variations for product analysis
GB/T 222-2006 — Permissible tolerances for chemical composition of steel products
GB/T 222-2025 — Steels and alloys - Permissible deviations of product analyzed chemical composition
GB/T 30063-2013
$125.00