GB/T 29756-2013Test methods of physical property for dry-mix mortar (English PDF)
干混砂浆物理性能试验方法
This is a limited preview
Buy now to download the full PDF (23 pages)
Need quotation for your management?
Get a formal quotation for GB/T 29756-2013 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
September 18, 2013
Implementation date
June 1, 2014
Scope
GB/T 29756-2013 is the English-translated version of 干混砂浆物理性能试验方法.
GB/T 29756-2013 is the Chinese standard "Test methods of physical property for dry-mix mortar".
Its scope clause reads: This standard specifies the dry mortar organic matter content, fresh mortar consistency (jump tables Act), fresh mortar density, air content of fresh mortar, hardening Flexural and compressive strength of hardened mortar water absorption, tensile bond strength of hardened mortar, mortar lateral deformation hardening and hardening mortar shrinkage Physical performance test method.
This standard applies to the determination of the dry mix mortar relevant physical properties. Its clauses include terms and definitions; standard test conditions; sample preparation; dry mortar organic content.
Found what you need?
Document preview — GB/T 29756-2013
National Standard of the People's Republic of China
- ICS
- 91.100.10
- Classification
- Q 11
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 a standard test conditions
- 5 Sample preparation
- 6 1 dry mortar organic content
- 7 fresh mortar consistency (jump tables Act)
- 8 fresh mortar density
- 9 fresh mortar air content
- 10 flexural compressive strength of hardened mortar
- 11 hardened mortar water absorption
- 12 hardened mortar tensile bond strength
- 13 lateral deformation hardening mortar
- 14 hardened mortar shrinkage
- Appendix A (normative) containing 16 gas analyzer calibration
- Appendix B (normative) Concrete slab
- Annex C (normative) mortar failure mode
1 Scope
This standard specifies the dry mortar organic matter content, fresh mortar consistency (jump tables Act), fresh mortar density, air content of fresh mortar, hardening
Flexural and compressive strength of hardened mortar water absorption, tensile bond strength of hardened mortar, mortar lateral deformation hardening and hardening mortar shrinkage
Physical performance test method.
This standard applies to the determination of the dry mix mortar relevant physical properties.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB 175 Common Portland Cement
GB/T 3810.5-2006 Test methods of ceramic tiles - Part 5. Determination of coefficient of restitution brick impact resistance
GB/T 17671-1999 cement mortar strength test method (ISO method) (idt ISO 679. 1989)
JC/T 681 planetary cement mortar mixer
JC/T 723 cement mortar shaker
JC/T 726 cement mortar test mode
JC/T 958 cement mortar fluidity tester (jump tables)
3 Terms and Definitions
The following terms and definitions apply to this document.
3.1 Lateral deformation
Shaped hardening mortar predetermined size by three-point bending load, specimen damage occurred before the maximum displacement.
4 Standard test conditions
Laboratory standard test conditions. temperature (23 ± 2) °C, relative humidity (50 ± 5)%, wind speed cyclic test area less than 0.2m/s.
5 Sample preparation
Test materials (including water) should be placed under standard test conditions more than 24h.
6 dry mortar organic content
6.1 Principle
The dry mortar after a specified high temperature burning, calculated as a percentage of volatile organic content of the mortar.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 23 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 29756-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 29756-2013
$385.00