GB/T 28948-2012Commercial vehicle -- Front towing attachments (English PDF)
Also coversGBT28948-2012
Open the GB/T 28948-2012 preview as PDF
This is a limited preview
Buy now to download the full PDF
Issued by
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Level / Type
National · Recommended
Issue date
December 31, 2012
Implementation date
July 1, 2013
Scope
GB/T 28948-2012 (Commercial vehicle -- Front towing attachments) is available as an English-translated PDF.
GB/T 28948-2012 — This standard specifies performance requirements for traction connecting device is installed in the commercial vehicle front end. This standard applies to the total mass of more than 3.5t maximum design of passenger cars, trucks and tractor-trailer. This standard does not apply to special operations vehicles.
Document preview — GB/T 28948-2012
National Standard of the People's Republic of China
- ICS
- 43.080
- Classification
- T 33
Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 General requirements
- 4.5 All removable parts should be reliable traction device to prevent failure.
- 4.7 traction process, the traction device shall not damage rope, cable or rod.
- 4.8 traction process, ropes, cables or rod can not be loose.
- 5 Performance Requirements
- 5.1 traction device can withstand a minimum static load F as follows.
Foreword
This standard was drafted according to GB/T 1.1-2009 given rules.
This standard uses the redrafted law, with reference to ISO 8035.1991 Commercial road vehicles and passenger front-end "mass exceeding 3.5t traction
Content means "the non-equivalent.
This standard by the National Automotive Standardization Technical Committee (SAC/TC114) centralized.
This standard was drafted. China Automotive Technology and Research Center, Anhui Jianghuai Automobile Co., Ltd., Beiqi Foton Motor Company Limited
Division, Hanyang Special Purpose Vehicle Research Institute.
1 Scope
This standard specifies performance requirements for traction connecting device is installed in the commercial vehicle front end.
This standard applies to the total mass of more than 3.5t maximum design of passenger cars, trucks and tractor-trailer.
This standard does not apply to special operations vehicles.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 3730.1-2001 car and trailer types of terms and definitions (ISO 3833.1999, MOD)
GB/T 3730.2-1996 road vehicle mass Vocabulary and codes (idt ISO 1176.1990)
GB/T 4781 Road vehicles - 50 mm drawbar ring hanging interchangeability (GB/T 4781-2006, ISO 1102.2001, IDT)
ISO 5422. 1982 Road vehicles towing ropes, cables or rods fixed point (Roadvehicle-Anchoragesfor
towingropes, cablesorbars)
3 Terms and Definitions
GB/T 3730.1-2001 and GB/T 3730.2-1996, ISO 5422 Definition of terms and definitions apply to this document.
4 General requirements
4.1 maximum design total mass of more than 3.5t of passenger cars, trucks and tractor-trailer towing or other should be able to ensure that the design and construction
Vehicle traction.
4.2 traction device can be used ropes, cables, or one rod, and does not require special tools and accessories.
4.3 traction device structure and shape is determined by the vehicle manufacturer, but performance should meet the requirements of this standard.
4.4 traction device should be installed in front of the vehicle, the vehicle must not exceed the contours (body plus bumper) in the horizontal plane of projection, is led by
Except when cited state.
4.5 All removable parts should be reliable traction device to prevent failure.
4.6 and the tractor hitch between the tractor (rope or drawbar) ends allow horizontal +/- 50 °, +/- 6 ° vertical displacement.
4.7 traction process, the traction device shall not damage rope, cable or rod.
4.8 traction process, ropes, cables or rod can not be loose.
4.9 For drawbar hitch, its appearance should be consistent with GB/T 4781 regulations (limited plug connecting device).
5 Performance Requirements
5.1 traction device can withstand a minimum static load F as follows.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — all pages — is available in the English PDF.
Referenced standards
Normative references
ISO 3833.1999 · GB/T 3730.2-1996 · ISO 1176.1990 · GB/T 4781 · GB/T 4781-2006 · ISO 1102.2001 · ISO 5422
How to Buy GB/T 28948-2012
- 1Add to cart. Click the "Buy GB/T 28948-2012" button on this page. You can add more standards before checkout.
- 2Checkout. Enter your email and billing details. Payment is processed securely by Stripe (cards, Apple Pay, Google Pay supported).
- 3Instant delivery (0–9 sec). Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4Invoice included. A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 47810-2026 — Test requirements for the electrical performance of navigation satellites
GB/T 47811-2026 — Mechanical interface requirements between launch vehicles and stacked flat-panel satellites
GB/T 47813-2026 — General specification for the tether launching and retrieving mechanism of tethered aerostats
Secure payment via Stripe
Payments accepted
GB/T 28948-2012
$70.00