Valid

GB/T 28861-2012Test method for measuring melt fluidity of encapsulating material of powdered epoxy (English PDF)

环氧粉末包封料熔融流动性试验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (13 pages)

Need quotation for your management?

Get a formal quotation for GB/T 28861-2012 in 30 minutes.

Issued by

General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China

Level / Type

National · Recommended

Issue date

November 5, 2012

Implementation date

February 15, 2013

Scope

GB/T 28861-2012 is the English-translated version of 环氧粉末包封料熔融流动性试验方法.

GB/T 28861-2012 — This standard specifies the encapsulation materials epoxy powder flowability and inclined horizontal flow test methods. This standard applies to epoxy powder encapsulation materials melt flow measurement.

Found what you need?

Document preview — GB/T 28861-2012

National Standard of the People's Republic of China

ICS
31.020
Classification
L 04

Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 4 devices and materials
  • 4.1 electric heated blast drying oven, heated to 300 degrees C, temperature control of +/- 2 degrees C.
  • 4.2 brass sample holder, the slope of 65 ° +/- 30 '.
  • 4.3 mercury thermometer, range 0 degrees C ~ 250 degrees C, minimum scale 1 degrees C.
  • 4.4 stopwatch, indexing 0.2 seconds.
  • 4.5 balance, a sense of the amount of 0.01g.
  • 4.6 vernier caliper, 120mm, precision 0.02mm.
  • 4.7 the glass sheet, 110mm x 50mm x 2.5mm.
  • 4.10 may regulator furnace.
  • 4.11 polytetrafluoroethylene (PTFE) aerosol sprayers.

Foreword

This standard was drafted in accordance with GB/T 1.1-2009 given rules.

The standard equipment by the National Standardization Technical Committee and the semiconductor material (SAC/TC203) and focal points.

This standard is mainly drafted by. Xianyang Reid Electronic Technology Co., Ltd., Xianyang Wei-hua Insulation Materials Co., Ltd., China Electronics Technology Standard

Associate of the Institute.

1 Scope

This standard specifies the encapsulation materials epoxy powder flowability and inclined horizontal flow test methods.

This standard applies to epoxy powder encapsulation materials melt flow measurement.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein

Member. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 21782.9-2010 powder coatings - Part 9. Sampling

Principle 3

Epoxy powder coating material is pressed into a cylindrical mold standard size, made of molded specimen. At a predetermined temperature, the sample is placed in the horizontal holder

Or on a predetermined angle of inclination of the glass holder to maintain a predetermined time after the sample is taken out carrying glass, natural air to room temperature measurements. tilt

Liquidity is represented by the total length of sample after melt flow. The level of liquidity than the melting sample for the sample before and after the diameter of the variable diameter of the initial one hundred

Fraction representation.

After the hot-plate horizontal flow test method is a hot plate heated to a predetermined temperature and constant, the molded sample was placed on a hot plate, the count immediately

When, after holding a predetermined time, vernier caliper diameter of the sample, with the sample before and after the melting of the sample than the diameter of the variable diameter of the initial one hundred

Fraction representation.

4 devices and materials

4.1 electric heated blast drying oven, heated to 300 degrees C, temperature control of +/- 2 degrees C.

4.2 brass sample holder, the slope of 65 ° +/- 30 '.

4.3 mercury thermometer, range 0 degrees C ~ 250 degrees C, minimum scale 1 degrees C.

4.4 stopwatch, indexing 0.2 seconds.

4.5 balance, a sense of the amount of 0.01g.

4.6 vernier caliper, 120mm, precision 0.02mm.

4.7 the glass sheet, 110mm x 50mm x 2.5mm.

4.8 steel cylindrical press molding machine, and a connecting rod, a cylindrical mold cavity diameter 10mm +/- 0.06mm, the height of 7.0mm +/- 0.05mm.

4.9 hot plate, brass plate smooth surface, thickness 15mm ~ 20mm, diameter of 120mm or 120mm x 120mm. For the side

Insert the thermometer diameter 7mm, 65mm deep holes.

4.10 may regulator furnace.

4.11 polytetrafluoroethylene (PTFE) aerosol sprayers.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 13 pages — is available in the English PDF.

Referenced standards

How to Download GB/T 28861-2012

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
13 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 28861-2012

$85.00