GB/T 28515.1-2012Test specifications for automatically switched optical network (ASON) - Part 1: Test specifications for SDH-based ASON (English PDF)
自动交换光网络(ASON)测试方法 第1部分:基于SDH的ASON
This is a limited preview
Buy now to download the full PDF (113 pages)
Need quotation for your management?
Get a formal quotation for GB/T 28515.1-2012 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
June 29, 2012
Implementation date
October 1, 2012
Scope
GB/T 28515.1-2012 is the English-translated version of 自动交换光网络(ASON)测试方法 第1部分:基于SDH的ASON.
GB/T 28515.1-2012 is the Chinese standard "Test specifications for automatically switched optical network (ASON) - Part 1: Test specifications for SDH-based ASON".
Its scope clause reads: This part of the standard specifies the transport plane SDH Automatic Switched Optical Network (ASON) based control plane, management plane, signaling Communication Network (SCN), the protection of test recovery, ASON network services, interoperability with traditional SDH network, and other aspects of planning and simulation software content.
This section applies to devices based on SDH ITU-TG.783 function defined for the transport plane ASON network. Note. Unlike the traditional SDH network interoperability testing, see Appendix A, planning simulation software functional verification Appendix B. Its clauses include abbreviations.
Found what you need?
Document preview — GB/T 28515.1-2012
National Standard of the People's Republic of China
- ICS
- 33.040.01
- Classification
- M 33
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Abbreviations
- 4 ASON Test Reference Model
- 4.1 ASON network reference point
- 4.2 Test Network Configuration Principle
- 5 transport plane test
- 5.1 SDH optical interface test
- 5.2 Electrical Test
- 5.3 Ethernet Interface Test
- 5.4 cross-connect verification
- 5.5 Test 7 overhead
- 5.7 Single jitter and delay test adapter
- 5.8 Performance Test 9 transport plane
- 5.9 Clock Function/Performance Test
- 6 control plane functional test
- 6.3 auto-discovery function test
- 6.4 Distributed Control Validation
- 6.5 ASON control plane reliability testing
- 7 control plane performance testing
- 7.1 connection setup and teardown time
- 7.2 routing protocol convergence time
- 8 ASON control plane protocol test
- 8.1 E-NNI protocol test
- 8.2 UNI interface protocol test
- 9 Signalling Communications Network (SCN) Test
- 9.1 SCN transfer mode test
- 9.2 SCN protection recovery testing
- 10 ASON management plane test
- 10.1 61 transport plane management function tests
- 10.2 the control plane management function test
- 10.3 SCN management function test
- 10.4 Maintenance management plane
- 11 ASON network protection recovery testing
- 11.1 based on 73 transport plane protection testing
- 11.2 Testing control plane-based protection
- 11.3 Network Recovery Test
- 11.4 combine protection and recovery
- 11.5 Online change the business protection and restoration of property
- 11.6 high traffic protection and recovery testing
- 11.8 VC12/VC3 lower order of business protection and restoration function test
- 11.9 Inter-domain protection and restoration
- 12 Business Test
- 12.1 Bandwidth on Demand service (BoD)
- 12.2 Optical Virtual Private Network (OVPN) business
- 12.3 102 timer reservation business
- 12.4 PC business to migrate to SPC Business
- 12.5 SPC business migrated to the PC business
- Appendix A (informative) and ASON network and traditional network example
- Annex B (informative) Planning Optimizer functional verification
1 Scope
This part of the standard specifies the transport plane SDH Automatic Switched Optical Network (ASON) based control plane, management plane, signaling
Communication Network (SCN), the protection of test recovery, ASON network services, interoperability with traditional SDH network, and other aspects of planning and simulation software content.
This section applies to devices based on SDH ITU-TG.783 function defined for the transport plane ASON network.
Note. Unlike the traditional SDH network interoperability testing, see Appendix A, planning simulation software functional verification Appendix B.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 16814-2008 synchronous digital hierarchy (SDH) optical fiber cable line systems
GB/T 21645.1-2008 Automatic Switched Optical Network (ASON) technical requirements - Part 1. Architecture and general requirements
YD/T 900-1997 SDH equipment clock technical requirements ---
YD/T 974-1998 SDH digital cross-connect equipment (SDXC) technical requirements and test methods
YD/T 1238-2002 based on SDH multi-service transport nodes technical requirements
YD/T 1267-2003 based on SDH transmission network synchronization network technical requirements
YD/T 1276-2003 based on SDH multi-service transport node test method
YD/T 1289.2-2003 Synchronous Digital Hierarchy (SDH) transmission network management technology - Part 2. Element Management System (EMS) Function
ITU-TG.781 synchronization layer functions (Synchronizationlayerfunctions)
ITU-TG.783 SDH equipment functional blocks (Characteristicsofsynchronousdigitalhierarchy (SDH) equipmentfunctionalblocks)
3 Abbreviations
AIS Alarm Indication Signal AlarmIndicationSignal
ASON Automatic Switched Optical Network AutomaticalySwitchedOpticalNetwork
BoD Bandwidth on demand BandwidthonDemand
CE client device ClientElement
CoS Service Level ClassofService
CTP Connection Termination Point ConnectionTerminationPoint
DCC data communication path DataCommunicationsChannel
ECC Embedded Control Channel EmbeddedControlChannel […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 113 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 16814-2008Methods of measurement for Synchronous digital Hierarchy (SDH) optical fiber cable line system
- GB/T 21645.1-2008Technical requirements for automatically switched optical network -- Part 1: Architecture and general requirements
- YD/T 1238-2002Technical requirement for SDH multi-service transport platform
- YD/T 1267-2003Technical specification for synchronization network based on SDH transport network
- YD/T 1276-2003Testing methods of SDH multi-service transport platform
- YD/T 1289.2-2003Synchronous Digital Hierarchy (SDH) transport network management system technical specification. Part 2: Element Management System (EMS) function
YD/T 900-1997
Similar standards
How to Download GB/T 28515.1-2012
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 16814-2008 — Methods of measurement for Synchronous digital Hierarchy (SDH) optical fiber cable line system
GB/T 21645.1-2008 — Technical requirements for automatically switched optical network -- Part 1: Architecture and general requirements
YD/T 1238-2002 — Technical requirement for SDH multi-service transport platform
Secure payment via Stripe
Payments accepted
GB/T 28515.1-2012
$1,520.00