GB/T 28474.1-2012Pressure/Differential-pressure transmitters for use in industrial-process measure and control systems - Part 1: General specification (English PDF)
工业过程测量和控制系统用压力/差压变送器 第1部分:通用技术条件
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 28474.1-2012 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
June 29, 2012
Implementation date
November 1, 2012
Scope
GB/T 28474.1-2012 is the English-translated version of 工业过程测量和控制系统用压力/差压变送器 第1部分:通用技术条件.
GB/T 28474.1-2012 is the Chinese standard "Pressure/Differential-pressure transmitters for use in industrial-process measure and control systems - Part 1: General specification".
Its scope clause reads: This section GB/T 28474 specifies the general technical conditions for industrial process measurement and control systems using pressure/differential pressure transmitter, including Terms and definitions, classification, requirements, marking, instructions, packaging and storage.
This section applies to industrial process measurement and control systems using pressure/differential pressure transmitter (hereinafter referred to as the transmitter).
This section does not apply to pneumatic transmitter. Transmitter special working conditions should also meet the requirements of the relevant standards.
Found what you need?
Document preview — GB/T 28474.1-2012
National Standard of the People's Republic of China
- ICS
- 25.040.40
- Classification
- N 10
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- Appendix A of this part is a normative appendix.
- 1 Scope
- 2 Normative references
1 Scope
This section GB/T 28474 specifies the general technical conditions for industrial process measurement and control systems using pressure/differential pressure transmitter, including
Terms and definitions, classification, requirements, marking, instructions, packaging and storage.
This section applies to industrial process measurement and control systems using pressure/differential pressure transmitter (hereinafter referred to as the transmitter).
This section does not apply to pneumatic transmitter.
Transmitter special working conditions should also meet the requirements of the relevant standards.
2 Normative references
The following documents contain provisions which, through reference GB/T 28474 in this section constitute provisions of this section. For dated reference documents
Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section
Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
GB/T 1048 pipe components --- PN (nominal pressure) of the definition and selection (GB/T 1048-2005, ISO /CD7268.1996,
MOD)
GB/T 3369.1 process control systems with analog signals - Part 1. DC current signal (GB/T 3369.1-2008,
IEC 60381-1. 1982, IDT)
GB/T 3369.2 process control systems - analog signals - Part 2. DC voltage signal (GB/T 3369.2-2008,
IEC 60381-2. 1978, IDT)
GB 3836.1 explosive atmospheres - Part 1. General requirements Equipment (GB 3836.1-2010, IEC 60079-0.2007,
MOD)
GB 3836.2 explosive atmospheres - Part 2. the flameproof "d" protection devices (GB 3836.2-2010, IEC 60079-1.
2007, MOD)
GB 3836.4 explosive atmospheres - Part 4. the intrinsically safe "i" Device Protection (GB 3836.4-2010, IEC 60079-
11.2006, MOD)
GB 4208 housing protection (IP Code) (GB 4208-2008, IEC 60529.2001, IDT)
GB 4793.1 measurement, control and laboratory safety requirements for electrical equipment Part 1. General requirements (GB 4793.1-
2007, IEC 61010-1.2001, IDT)
GB/T 9969.1-2008 Instructions General Industrial Products
GB/T 13384 mechanical and electrical products packaging General technical conditions
GB/T 15479-1995 Industrial Automation Instrumentation Isolation resistance strength technical requirements and test methods
GB/T 17212 industrial process measurement and control - Terms and definitions (GB/T 17212-1998, idt IEC 60902. 1987)
GB/T 17614.1 industrial process control systems Transmitters - Part 1. Methods of evaluating performance (GB/T 17614.1-2008,
IEC 60770-1.1999, IDT)
GB/T 18271.1 process measurement and control devices - General methods and procedures for evaluating performance - Part 1. General (GB/T 18271.1-2000, idt IEC 61298-1.1995) […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 28474.1-2012
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 28474.2-2012 — Pressure/Differential-pressure transmitters for use in industrial-process measure and control systems - Part 2: Methods of evaluating the performance
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 28474.1-2012
$195.00