GB/T 27751-2011Specification for AgNiC contact (English PDF)
银镍石墨电触头技术条件
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 27751-2011 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 30, 2011
Implementation date
May 1, 2012
Scope
GB/T 27751-2011 is the English-translated version of 银镍石墨电触头技术条件.
GB/T 27751-2011 is the Chinese standard "Specification for AgNiC contact". Its scope clause reads: This standard specifies the method of powder metallurgy and solid phase sintering of nickel silver flake graphite electrical contacts requirements, test methods, inspection rules, marks, packages Loading, transport and storage.
This standard applies to solid-phase sintering and powder metallurgy production of nickel-silver flake graphite electrical contacts (hereinafter referred to as electrical contacts) testing and inspection Income.
The products are mainly used in the circuit breaker. Its clauses include requirements.
Found what you need?
Document preview — GB/T 27751-2011
National Standard of the People's Republic of China
- ICS
- 29.120.99
- Classification
- K 14
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Requirements
- 3.1 Dimensions, tolerances and annotations
- 3.2 surface quality
- 3.3 symbols, chemical composition and mechanical properties of the physical
1 Scope
This standard specifies the method of powder metallurgy and solid phase sintering of nickel silver flake graphite electrical contacts requirements, test methods, inspection rules, marks, packages
Loading, transport and storage.
This standard applies to solid-phase sintering and powder metallurgy production of nickel-silver flake graphite electrical contacts (hereinafter referred to as electrical contacts) testing and inspection
Income. The products are mainly used in the circuit breaker.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 2828.1-2003 Sampling procedures for inspection - Part 1. by acceptance quality limit (AQL) retrieval batch test sample plan
GB/T 5586 electrical contact materials basic performance test method
GB/T 5587-2003 silver based electrical contacts basic shapes, dimensions, symbols and designations
GB/T 26871 Test method for electrical contact materials microstructure
GB/T 26872 electrical contact material microstructure map
JB/T 4107.4-1999 Determination of electrical contact materials for chemical analysis of tungsten silver silver content (iodometry)
JB/T 4107.5-1999 electrical contact materials for chemical analysis of silver Determination of nickel content in nickel (ETDA volumetric method)
JB/T 4107.7-1999 electrical contact materials - Determination of carbon content - Silver graphite (gas volumetric method for the determination of carbon content)
3 Requirements
3.1 Dimensions, tolerances and annotations
Electrical contacts dimensions, tolerances and labeling shall comply with the requirements of GB/T 5587-2003 and 3.1 in Chapter 4. If you have special requirements,
Agreed to by the supply and demand sides.
3.2 surface quality
3.2.1
electrical contact surface should be free of cracks, bubbling, delamination, lack of edge, off angle; there should be no more than 0.10mm high edge burrs.
3.2.2
electrical contact surface should not have rust length greater than 0.20mm.
3.3 symbols, chemical composition and mechanical properties of the physical
Electrical contacts symbol, chemical composition and mechanical physical properties should meet the requirements of Table 1.
GB/T 38090-2019 | GB/T 3217-2013 | GB/T 29628-2013 | GB/T 47349-2026 | GB/T 47344-2026 | GB/T 20235-2026 | […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 27751-2011
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 27751-2011
$105.00