Valid

GB/T 26946.1-2011Single side loading fork-lift trucks -- Part 1: Stability tests (English PDF)

Preview PDF

This is a limited preview

Buy now to download the full PDF (7 pages)

Need quotation for your management?

Get a formal quotation for GB/T 26946.1-2011 in 30 minutes.

Issued by

Standardization Administration of China

Level / Type

National · Recommended

Issue date

September 29, 2011

Implementation date

February 1, 2012

Scope

GB/T 26946.1-2011 (Single side loading fork-lift trucks -- Part 1: Stability tests) is available as an English-translated PDF.

GB/T 26946.1-2011 — This section GB/T 26946 specifies the (hereinafter referred to as cross validation with tiltable or non-mast tilt or fork truck side Stability of the car) basic test.

This section applies equipped with forks and/or attachment of the truck. This section does not apply to trucks transporting freely swinging suspension loads.

Found what you need?

Document preview — GB/T 26946.1-2011

National Standard of the People's Republic of China

ICS: 53.060
Classification: J 83

Issued by: Standardization Administration of China

Foreword
1 Scope
2 Normative references
3 Test purposes
3.1 Normal operating conditions
3.2 Non-normal operating conditions
4 Stability Test
4.1 Test requirements
4.2 Authentication method

Foreword

GB/T 26946 "side of the truck" is divided into two parts.

--- Part 1. Stability test;

--- Part 2. Handling 6m and above the length of the truck freight containers Additional stability tests.

This section GB/T Part of 126,946.

This part identical with ISO 13563-1:2001 "side of the truck - Part 1. Stability Test" (in English).

This section is equivalent translation ISO 13563-1:2001.

For ease of use, this section made the following editorial changes.

--- Deleted international standards foreword;

--- 4.3.2 unset point M and N points;

--- Table 2 units were centralized labeling;

--- 2 to 17 moved to table 3;

--- Figures 2, 3, 4, 10, 11, 12, XY has been re-labeled;

--- FIG. 13, FIG. 14 to increase the longitudinal center plane of the truck;

--- 17 were complements.

This part is proposed by China Machinery Industry Federation.

This part of the National Standardization Technical Committee Vehicle (SAC/TC332) centralized.

This section is responsible for drafting unit. Anhui Heli Co., Ltd., Beijing Materials Handling Design and Research Institute.

Participated in the drafting of this section. Xiamen, Xiamen Engineering Machinery Company Limited.

1 Scope

This section GB/T 26946 specifies the (hereinafter referred to as cross validation with tiltable or non-mast tilt or fork truck side Stability of the car) basic test.

This section applies equipped with forks and/or attachment of the truck.

This section does not apply to trucks transporting freely swinging suspension loads.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 8591 moving machinery - Seat index point (GB/T 8591-2000, eqv ISO 5353:1995)

3 Test purposes

3.1 Normal operating conditions

Have sufficient basic stability test specified in this part, to ensure the correct use of this type of truck in the following normal operating conditions Qualitative, namely.

a) running on a solid, flat, level and paved roads and stacking operations;

b rear) mast or fork tilt, load retracted and at a lower (run) position, load or run on the stage of the state;

c) In the mast substantially vertical, substantially horizontal state under the fork stacking;

d) load center of gravity about the job performed within the center plane between the mast uprights.

3.2 Non-normal operating conditions

When not working with the same conditions as specified in 3.1 should be used.

a) meet specific criteria GB/T 26946 in other parts of the corresponding provisions of the forklift; or Stability b) agreed by the relevant truck, but test the stability of not less than the requirements set out under normal operating conditions (see 3.1).

4 Stability Test

4.1 Test requirements

Lateral stability truck should be in one of the test methods specified in 4.2 to be verified.

4.2 Authentication method

4.2.1 Tilt platform

You should use about one side of the tilt test platform. The truck will be tried according to the conditions specified in 4.3, and placed in an initial horizontal state on a test platform, and then press each location given in Table 3 were tested sequentially.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 7 pages — is available in the English PDF.

Referenced standards

Normative references

GB/T 8591 · GB/T 8591-2000 · ISO 5353

How to Download GB/T 26946.1-2011

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.