Valid

GB/T 26416.9-2023Chemical analysis methods for rare earth ferroalloy—Part 9: Determination of phosphorus content—Bismuth phosphomolybdate blue spectrophotometry (English PDF)

稀土铁合金化学分析方法 第9部分:磷量的测定 铋磷钼蓝分光光度法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 26416.9-2023 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

May 23, 2023

Implementation date

December 1, 2023

Scope

GB/T 26416.9-2023 is the English-translated version of 稀土铁合金化学分析方法 第9部分:磷量的测定 铋磷钼蓝分光光度法.

GB/T 26416.9-2023 is Part 9 of GB/T 26416 and gives the bismuth phosphomolybdate blue spectrophotometric method for the phosphorus content of a rare earth iron alloy.

It applies to lanthanum-iron, cerium-iron, lanthanum-cerium-iron, neodymium-iron, dysprosium-iron, gadolinium-iron, holmium-iron and yttrium-iron alloys, over a measuring range of 0.0050 % to 0.20 % mass fraction.

The sample is decomposed with hydrochloric and nitric acid and fumed with perchloric acid so that phosphorous acid is oxidised to orthophosphoric acid; in sulfuric acid medium the phosphorus, bismuth and ammonium molybdate form a yellow ternary heteropoly acid, ascorbic acid reduces it to a blue complex, and the absorbance is read at a wavelength of 700 nm.

It cites GB/T 6682 and GB/T 8170. It was issued on 23 May 2023 and has applied since 1 December 2023.

Found what you need?

Document preview — GB/T 26416.9-2023

National Standard of the People's Republic of China

ICS
77.120.99
Classification
H 14

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • Introduction
  • 1 Scope
  • 2 Normative references
  • 3 Terms and Definitions
  • 4 Method Summary
  • 5 Reagents or Materials

Foreword

This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for Standardization Work Part 1: Structure and Drafting Rules for Standardization Documents" drafting.

This document is part 9 of GB/T 26416 "Methods for Chemical Analysis of Rare Earth Ferroalloys". GB/T 26416 has issued the following part.

--- Part 1. Determination of the total amount of rare earth;

--- Part 2. Determination of rare earth impurity content Inductively coupled plasma emission spectrometry;

--- Part 3. Determination of calcium, magnesium, aluminum, nickel, manganese content Inductively coupled plasma emission spectrometry;

--- Part 4. Determination of iron content Potassium dichromate titration method;

--- Part 5. Determination of oxygen content pulse-infrared absorption method;

--- Part 6. Determination of molybdenum, tungsten and titanium content Inductively coupled plasma emission spectrometry;

--- Part 7. Determination of carbon and sulfur content High-frequency-infrared absorption method;

--- Part 8. Photometric method for the determination of the amount of silicon;

--- Part 9. Determination of phosphorus content Bismuth phosphomolybdenum blue spectrophotometry.

Introduction

The rare earth iron alloy referred to in this document refers to the master alloy composed of iron and one or more rare earth elements, generally adopts molten salt electrolysis or fusion It is mainly used as an additive for magnetic materials such as NdFeB permanent magnet materials, magnetostrictive materials, optical and magnetic recording materials, or as a deoxidizer, Additives, etc. are used in iron and steel smelting. Chemical composition is an important assessment index of rare earth ferroalloys. GB/T 26416 "Chemical Analysis of Rare Earth Ferroalloys Method" integrates the industry standard XB/T 616-2012 "Chemical Analysis Method of Gadolinium-Fe Alloy", XB/T 621-2016 "Chemical Analysis Method of Holmium-Fe Alloy Analytical Methods", XB/T 623-2018 "Chemical Analysis Methods of Ferro-Cerium Alloys", XB/T 624-2018 "Chemical Analysis Methods of Ferro-Yttrium Alloys", etc.

Focusing on all rare earth ferroalloys (including ferro-lanthanum, ferrocerium, ferro-lanthanum, ferro-ndium, ferrodysprosium, ferro-gadolinium, ferro-holmium and ferro-yttrium) that have achieved large-scale production at present etc.) The chemical analysis method standards for the indicators that need to be assessed in production and application, including the total amount of rare earth, the content of rare earth impurities, and the content of non-rare earth impurities detection etc. According to the different detection objects and detection methods, as well as the differences in substrates, etc., GB/T 26416 consists of the following parts.

--- Part 1. Determination of the total amount of rare earth;

--- Part 2. Determination of rare earth impurity content Inductively coupled plasma emission spectrometry;

--- Part 3. Determination of calcium, magnesium, aluminum, nickel, manganese content Inductively coupled plasma emission spectrometry;

--- Part 4. Determination of iron content Potassium dichromate titration method;

--- Part 5. Determination of oxygen content pulse-infrared absorption method;

--- Part 6. Determination of molybdenum, tungsten and titanium content Inductively coupled plasma emission spectrometry;

--- Part 7. Determination of carbon and sulfur content High-frequency-infrared absorption method;

--- Part 8. Photometric method for the determination of the amount of silicon;

--- Part 9. Determination of phosphorus content Bismuth phosphomolybdenum blue spectrophotometry.

The above-mentioned standards have clarified the scope of application, standardized reagents, materials, test equipment and procedures, and have been repeatedly tested by many laboratories.

The precision data given by the repeated tests and verifications has enhanced the consistency and comparability of data between different laboratories, and provided a basis for the quality assurance of rare earth ferroalloys. Establish a rigorous and standardized standardization work foundation.

This document mainly adopts the bismuth phosphomolybdenum blue spectrophotometric method to determine the phosphorus content in rare earth iron alloys, which has the advantages of wide measurement range, high sensitivity and stability. Good sex and other characteristics. The precision data in this document is based on the joint test conducted by 7 laboratories on 5 samples with different levels in 2022.

Each laboratory independently measures the phosphorus content of each level 11 times under repeatability conditions, and conducts statistics according to GB/T 6379.2 analyze.

1 Scope

This document describes the rare earth ferroalloys (lanthanum ferroalloy, cerium ferroalloy, lanthanum ferrocerium alloy, neodymium ferroalloy, dysprosium ferroalloy, gadolinium ferroalloy, holmium ferroalloy Alloy, yttrium-iron alloy) Determination of phosphorus content.

This document is applicable to rare earth iron alloys (lanthanum-iron alloy, cerium-iron alloy, lanthanum-cerium-iron alloy, neodymium-iron alloy, dysprosium-iron alloy, gadolinium-iron alloy, holmium-iron alloy Alloy, yttrium-iron alloy) Determination of phosphorus content. Measuring range (mass fraction). 0.0050%~0.20%.

2 Normative references

The contents of the following documents constitute the essential provisions of this document through normative references in the text. Among them, dated references For documents, only the version corresponding to the date is applicable to this document; for undated reference documents, the latest version (including all amendments) is applicable to this document.

GB/T 6682 Analytical laboratory water specifications and test methods

GB/T 8170 Numerical rounding off rules and expression and determination of limit values

3 Terms and Definitions

This document does not have terms and definitions that need to be defined.

4 Method Summary

The sample is decomposed by hydrochloric acid and nitric acid, and perchloric acid is added to smoke, and phosphorous acid is oxidized to orthophosphoric acid. In sulfuric acid medium, phosphorus, bismuth and ammonium molybdate A yellow phosphorus, bismuth, and molybdenum ternary heteropolyacid is formed, which is reduced to a blue complex with ascorbic acid, and the absorption is measured at a spectrophotometer wavelength of 700nm. Photometrically, calculate the phosphorus content.

5 Reagents or Materials

Unless otherwise specified, in the analysis, only reagents confirmed to be of analytical grade or higher and distilled substances of grade two or higher in accordance with GB/T 6682 were used.

Distilled or deionized water or water of equivalent purity. Prefer certified standard solutions.

5.1 Hydrochloric acid (rho=1.19g/mL, superior grade).

5.2 Nitric acid (rho=1.42g/mL, superior grade).

5.3 Perchloric acid (rho=1.67g/mL).

5.4 Mixed acid solution. Add 37.5mL of hydrochloric acid (5.1) and 12.5mL of nitric acid (5.2), add 50mL of water, and mix well.

5.5 Sulfuric acid (1 3; superior grade).

5.6 Bismuth nitrate solution (10g/L). Weigh 10g bismuth nitrate, put it in a 200mL beaker, add 30mL nitric acid (5.2), heat to dissolve.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download GB/T 26416.9-2023

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 26416.9-2023

$150.00