GB/T 26084-2010General specification for electric rubber products of ship (English PDF)
船舶电气橡胶制品通用技术条件
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 26084-2010 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
January 10, 2011
Implementation date
July 1, 2011
Scope
GB/T 26084-2010 is the English-translated version of 船舶电气橡胶制品通用技术条件.
GB/T 26084-2010 is the Chinese standard "General specification for electric rubber products of ship". Its scope clause reads: This standard specifies the marine electrical rubber products (including seals and insulation, referred to rubber) application environment conditions, requirements, testing Methods and inspection rules.
This standard applies to ships electrical equipment used rubber products and acceptance. Its clauses include environmental conditions; requirements.
Found what you need?
Document preview — GB/T 26084-2010
National Standard of the People's Republic of China
- ICS
- 47.020.05
- Classification
- U 05
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Environmental Conditions
- 4 Requirements
1 Scope
This standard specifies the marine electrical rubber products (including seals and insulation, referred to rubber) application environment conditions, requirements, testing
Methods and inspection rules.
This standard applies to ships electrical equipment used rubber products and acceptance.
2 Normative references
The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent
Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research
Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.
GB/T 528 vulcanized rubber or thermoplastic rubber tensile stress strain properties (GB/T 528-2009, ISO 37.2005,
IDT)
Determination of GB/T 529 vulcanized rubber or thermoplastic rubber tear strength (Trouser, angle and crescent test pieces) (GB/T 529-
2008, ISO 34-1.2004, MOD)
GB/T 531.1 vulcanized rubber or thermoplastic rubber hardness test pushed Part 1. Shore hardness method (Shore hardness) (GB/T 531.1-2008, ISO 7619-1.2004, IDT)
GB/T 1681 vulcanized rubber resilience Determination (GB/T 1681-2009, ISO 4662. 1986, IDT)
GB/T 1682 Determination of vulcanized rubber low temperature brittleness Single Specimen
Determination of GB/T 1692 vulcanized rubber insulation resistance
GB/T 1804-2000 General tolerances for linear and angular dimensions without individual tolerance tolerance (eqv ISO 2768-1. 1989)
GB/T 2423.16-2008 Environmental testing for electric and electronic products Part 2. Test methods - Test J and guidance. Mould growth (IEC 60068-2-10.2005, IDT)
GB/T 3512 vulcanized rubber or thermoplastic rubber hot air and heat accelerated aging test (GB/T 3512-2001, ISO 188.
1998, EQV)
GB/T 7759 vulcanized rubber, thermoplastic rubber at room temperature, high and low temperature compression set was measured (GB/T 7759-1996,
ISO 815.1991, EQV)
10707 Determination of GB/T burning rubber properties
CB1171.7 Marine Equipment Environmental Measurement mold
IMO/MSC.81 (70) IMO MSC resolution "life-saving equipment testing," October 15, 2007 Revision
3 Environmental Conditions
Rubber parts for the application of environmental conditions.
a) Ambient temperature. -30 °C ~ 60 °C;
b) Humidity. When the ambient temperature does not exceed 40 °C, relative humidity of 90% to 100%; when the ambient temperature exceeds 40 °C,
Relative humidity less than 70%.
4 Requirements
4.1 appearance quality
Rubber surface should be smooth, uniform color, no burr, cracks, bubbles, impurities and other defects.
GB/T 7094-2016 | CB 1146.8-1996 | CB 1146.9-1996 | GB/T 17848-2026 | GB/T 14616-2026 | GB/T 26085-2010 | […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 26084-2010
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 26084-2010
$125.00