GB/T 25848-2010Acid - resistant ceramic arched beam (English PDF)
耐酸陶瓷球拱
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 25848-2010 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
January 10, 2011
Implementation date
July 1, 2011
Scope
GB/T 25848-2010 is the English-translated version of 耐酸陶瓷球拱.
GB/T 25848-2010 is the Chinese standard "Acid - resistant ceramic arched beam".
Its scope clause reads: This standard specifies types, requirements, inspection and test methods, inspection rules, marking, instructions for use, packaging, transportation and storage of the industrial gamma-ray level meter (hereinafter referred to as the "level meter").
This standard is applicable to industrial gamma-ray level meters. Its clauses include type; requirements.
Found what you need?
Document preview — GB/T 25848-2010
National Standard of the People's Republic of China
- ICS
- 71.120
- Classification
- G 94
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword i
- 1 Scope
- 2 Normative references
- 3 Type
- 4 Requirements
- 5 Inspection and test methods
- 6 Inspection rules
- 7 Marking, instructions for use, packaging, transportation and storage
1 Scope
This standard specifies types, requirements, inspection and test methods, inspection rules, marking, instructions for use, packaging, transportation and storage of the industrial gamma-ray level meter (hereinafter referred to as the "level meter").
This standard is applicable to industrial gamma-ray level meters.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB 3836.1 Explosive atmospheres - Part 1: Equipment - General requirements
GB 3836.2 Explosive atmospheres - Part 2: Equipment protection by flameproof enclosures "d"
GB 4075 Sealed radioactive sources - General requirements and classification
GB/T 4208-2017 Degrees of protection provided by enclosure (IP code)
GB 8702 Controlling limits for electromagnetic environment
GB/T 8993 Environmental conditions and testing procedures for nuclear instrumentation
GB/T 9969 General principles for preparation of instructions for use of industrial products
GB 11806 Regulations for the safe transport of radioactive material
GB/T 13384 General specifications for packing of mechanical and electrical product
GB 14052-1993 Radionuclide gauges - Gauges designed for permanent installation
3 Type
3.1 Structural type
Level meters fall into two structural types:
a) Split type: It consists of three parts: radioactive source, detector and converter;
b) Integrated type: It consists of two parts: radioactive source and detector.
Note: "Split type" refers to the split body of detector and converter, and the signal detected by the detector is sent to the converter for processing. "Integrated type" refers to that the converter is removed, and the converter and detector are integrated.
3.2 Product classification
Level meters are divided into switch type and continuous type.
3.3 Parameters
3.3.1 Measuring range
100 mm to 8000 mm.
3.3.2
Output signal:
a) The output signal of switch is dry contact signal, and the contact capacity shall not be less than 20 W;
b) The continuous output signal is DC 4 mA ~ DC 20 mA current signal;
c) The integrated level meter carries out remote communication and debugging.
Note: DC refers to direct current (the same below).
3.4 Operating conditions
The normal operating conditions of the level meter are:
a) Ambient temperature:
Split type: the detector is -20°C ~ 50°C; the converter is 0°C ~ 50°C;
Integrated type: the detector is -20°C ~ 50°C;
b) Relative humidity: less than 90%.
c) Supply voltage: AC (220±22) V or DC (24±2.4) V.
d) There is no strong electromagnetic field interference and no strong vibration in the surrounding environment.
Note: AC refers to alternating current, and DC refers to direct current (the same below).
4 Requirements
4.1 Appearance
4.1.1
The enclosure of the level meter shall be smooth and intact, and the surface coating shall be painted and electroplated. There shall be no obvious scratches, bottom exposure, blistering, peeling, dirt and other phenomena.
4.1.2
The nameplate and mark of the level meter shall be clear.
4.1.3
Fasteners of the level meter shall not be loose, and various regulating devices shall rotate flexibly and function normally.
4.2 Requirements for explosion-proof performance
The explosion-proof performance of the level meter detector shall meet the requirements of GB 3836.1 and GB 3836.2, with an explosion proof certificate obtained.
4.3 Insulation resistance and strength
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 25848-2010
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 25848-2010
$165.00