GB/T 23564.1-2009Ball-bearing guide steel-plate punch holders of stamping dies - Part 1: Rear-pillar punch holders (English PDF)
冲模滚动导向钢板上模座 第1部分：后侧导柱上模座
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 23564.1-2009 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
April 2, 2009
Implementation date
January 1, 2010
Scope
GB/T 23564.1-2009 is the English-translated version of 冲模滚动导向钢板上模座 第1部分：后侧导柱上模座.
GB/T 23564.1-2009 is the Chinese standard "Ball-bearing guide steel-plate punch holders of stamping dies - Part 1: Rear-pillar punch holders". Its scope clause reads: This section GB/T 23564 specifies the die roll guide plate on the rear side of the guide pillar die mold base seat dimensions and markings.
This section applies to the die roll guide plate on the rear side of the punch holder guide pillar die holder. Its clauses include dimensions.
Found what you need?
Document preview — GB/T 23564.1-2009
National Standard of the People's Republic of China
- ICS
- 25.120.30
- Classification
- J 46
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
1 Scope
This section GB/T 23564 specifies the die roll guide plate on the rear side of the guide pillar die mold base seat dimensions and markings.
This section applies to the die roll guide plate on the rear side of the punch holder guide pillar die holder.
2 Normative references
The following documents contain provisions which, through reference GB/T 23564 in this section constitute provisions of this section. For dated references,
All subsequent amendments (excluding corrections) or revisions do not apply to this section, however, encourage an agreement under this section
Parties to study the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
JB/T 8050 Die mold technical conditions
JB/T 8070-2008 die mold parts and technical conditions
3 Dimensions
Rolling guide the rear guide post mold base structure and dimensions shown in Figure 1, Table 1.
Note. No Note the surface roughness R Rao 6.3µm.
Lifting screw position size is determined by the manufacturer.
Figure 1 rolling guide the rear guide post mold base […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 23564.1-2009
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 23564.2-2009 — Ball-bearing guide steel-plate punch holders of stamping dies - Part 2: Diagonal-pillar punch holders
GB/T 23564.3-2009 — Ball-bearing guide steel-plate punch holders of stamping dies - Part 3: Center-pillar punch holders
GB/T 23564.4-2009 — Ball-bearing guide steel-plate punch holders of stamping dies - Part 4: Four-pillar punch holders
Secure payment via Stripe
Payments accepted
GB/T 23564.1-2009
$85.00