Valid

GB/T 22135-2019Commissioning of electrical, instrumentation and control systems in the process industry - Specific phases and milestones (English PDF)

流程工业中电气、仪表和控制系统的试车各特定的阶段和里程碑

Preview PDF

This is a limited preview

Buy now to download the full PDF (51 pages)

Need quotation for your management?

Get a formal quotation for GB/T 22135-2019 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

June 4, 2019

Implementation date

January 1, 2020

Scope

GB/T 22135-2019 is the English-translated version of 流程工业中电气、仪表和控制系统的试车各特定的阶段和里程碑.

GB/T 22135-2019 is the Chinese standard "Commissioning of electrical, instrumentation and control systems in the process industry - Specific phases and milestones".

Its scope clause reads: This standard defines specific stages and milestones in the commissioning of electrical, instrumentation and control systems in the process industry (see Figure 1).

Pass By way of example, this standard describes the activities of a project after the "installed in place" milestone and before the installation is accepted by the owner.

Various types of related processes/devices. NOTE. This standard assumes that the "device acceptance" milestone occurs after the performance appraisal. If the scope of work is reduced, this standard should also be modified appropriately.

Note. Construction work and pre-commissioning work can be carried out at the same time. Figure 1 Definition of phases and milestones For pharmaceuticals or other industries with special requirements, in addition to complying with current standards, such as China's GMP standards, other standards should also be complied with. [Example.

GAMP (Good Automated Manufacturing Practice)], regulations and regulatory requirements. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 22135-2019

National Standard of the People's Republic of China

ICS: 25.040.40
Classification: N 10
Replacing: GB/Z 22135-2008

Issued by: State Administration for Market Regulation, China National Standardization Administration

Preface
Introduction
1 Scope
2 Normative references
3 Terms and Definitions
4 General preparation before device acceptance
5 Install in place
5.1 Mechanical property inspection and testing
5.2 Procedure
6 Pre-commissioning (mechanical completion)
6.1 General
6.2 Procedure
7 Test drive
7.1 General
7.2 Procedure
8 Performance assessment and device acceptance
8.1 General
8.2 Conditions for starting performance assessment
8.3 Implementation of Performance Assessment
8.4 Performance assessment report and assessment
Appendix A (Informative Appendix) List of Documents Required for Pre-commissioning and Commissioning Phase
Appendix B (informative) Description of pre-commissioning activities
Appendix C (Informative Appendix) Mechanical Completion Certificate
Appendix D (Informative Appendix) Description of Commissioning Activities
Appendix E (Informative Appendix) Device Acceptance Certificate
Appendix F (Informative Appendix) Special Matters in the Project

1 Scope

This standard defines specific stages and milestones in the commissioning of electrical, instrumentation and control systems in the process industry (see Figure 1). Pass

By way of example, this standard describes the activities of a project after the "installed in place" milestone and before the installation is accepted by the owner.

Various types of related processes/devices.

NOTE. This standard assumes that the "device acceptance" milestone occurs after the performance appraisal. If the scope of work is reduced, this standard should also be modified appropriately.

Note. Construction work and pre-commissioning work can be carried out at the same time.

Figure 1 Definition of phases and milestones

For pharmaceuticals or other industries with special requirements, in addition to complying with current standards, such as China's GMP standards, other standards should also be complied with.

[Example. GAMP (Good Automated Manufacturing Practice)], regulations and regulatory requirements.

2 Normative references

The following documents are essential for the application of this document. For dated references, only the dated version applies to this article pieces. For undated references, the latest edition (including all amendments) applies to this document.

ISO 10628-2 Chemical and petrochemical industry graphics - Part 2.Graphical symbols

The composition, content and presentation method of IEC 62079 specification

IEC 62424 Process Control Engineering Notation for P

Data Exchange Requirements

ISA-S7.0.01 Instrument Air Quality Standard

3 Terms and Definitions

The following terms and definitions apply to this document.

GB/T 20438.4 | GB/T 20438.5 | GB/T 20438.6 | GB/T 45616.1 | GB/T 11605 | […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 51 pages — is available in the English PDF.

Referenced standards

Normative references

ISO 10628 · IEC 62079 · IEC 62424

How to Download GB/T 22135-2019

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.