GB/T 19212.8-2012[GB/T 19212.8-2012] Safety of power transformers, power supplies, reactors and similar products -- Part 8: Particular requirements and tests for transformers and power supplies for toys (English PDF)

Foreword

All technical contents of this section GB 19212 is mandatory.

GB 19212 "power transformers, power supplies, reactors and similar products" 1) currently include the following.

1) This series of standards, some part under "power transformers, power supplies, reactors and similar products" heading, some parts in the "supply voltage

For the next 1100V and below transformers, reactors, power supply units and similar safety products, "the title, the title of this series of standards possible future releases

It will be modified.

--- Part 1. General requirements and tests;

--- Part 2. Particular requirements for the separation and general purpose test power transformers and transformer isolated built;

--- Part 3. Particular requirements for control and test transformer and the power of the built-in control transformer;

--- Part 4. gas oil burners and special requirements of the ignition transformer;

--- Part 5. Particular requirements and test power supply device built isolation transformer and the isolation transformer;

--- - Part 6. Particular requirements for shaver transformers and shaver power supply device;

--- Part 7. Particular requirements and test power supply unit and the safety isolating transformer of the built-in safety isolating transformer;

--- Part 8. Particular requirements for toys and test transformers and power supplies;

Section --- 9. Particular requirements for bell and bell transformer;

--- Part 10. Particular requirements for filament type portable III transformer;

--- Part 13. Particular requirements for constant voltage transformers;

--- Part 14. Particular requirements and tests auto transformers and power supply device built autotransformer;

--- Part 15. Particular requirements for the regulator;

--- Part 16. Particular requirements for supply of medical locations using isolation transformers;

--- Part 17. switching type power supply device and a switching power supply device and the special test requirements of transformers;

--- Part 20. Particular requirements for attenuating interference transformers;

--- Part 21. Particular requirements for small reactors;

--- Part 24. Particular requirements for transformers for construction sites.

Other parts are under consideration.

This is Part of 8 GB 19212. This section was developed on the basis of GB 19212.1-2008 on this part of the need to

GB 19212.1-2008 used in conjunction.

This section is 19212.1-2008 GB respective chapter, the strips supplemented and modified in order to GB 19212.1-2008 content of

Conversion of the present content portion. This section GB 19212.1-2008 for the newly added clause numbered starting from 101.

This section drafted in accordance with the rules GB/T 1.1-2009 given.

This partial replacement GB 19212.8-2006 "Safety Section 8 power transformers, power supply units and similar products. transformer toys

Special requirements "is compared with the GB 19212.8-2006, the main technical changes are as follows.

a) Standard name to "Safety Section 8 power transformers, power supplies, reactors and similar products. toys, power transformers and

Special requirements and tests ";

b) Chapter 1 increases with the content of the power-related aspects of the interior of the toy transformer, and a predetermined rated output voltage of the power supply the toy;

c) Chapter 2 adds a reference to IEC 60227-1 and IEC 60245-1 standards;

d) Chapter 3, the scope of the term modified "transformer"; the modified terms and definitions transformers for toys; Toys increased power

The terms and definitions source;

e) Chapter 6 adds the requirement for the nominal supply frequency;

f) modify the contents of 8.11, to complement the "symbol or graphic symbol" and "description or name" and "identification code"; adds Father

Mother tips of their contents;

g) modify the contents of 12.102, and supplemented ratio calculation formula;

h) modify the contents of Chapter 14;

i) modify and supplement the content of Chapter 19.

This section uses the translation method is equivalent to using 61558-2-7 IEC .2007 "power transformers, power supplies, reactors and similar products

Part 2-7. Particular requirements for toys and test "and the power transformer (English).

Consistency correspondence relationship with the international standard in normative documents referenced in our files are as follows.

--- GB/T 5023.1-2008 rated voltage of 450/750V and below PVC insulated cables - Part 1. General Requirements

(IEC 60227-1.2007, IDT);

--- GB/T 5013.1-2008 rated voltage of 450/750V rubber insulated cables and below Part 1. General Requirements

(IEC 60245-1.2003, IDT).

For ease of use, this part of the IEC 61558-2-7.2007 editorial changes are also made the following.

A) "in the present international standards" to "this section";

b) Delete IEC 61558-2-7.2007 Foreword.

Please note that some of the content of this document may involve patents. The issuing authority of this document does not assume responsibility to identify these patents.

This section was proposed by China Electrical Equipment Industrial Association.

This part of the National small power transformers, reactors, power supply apparatus and Similar Products Standardization Committee (SAC/TC418)

Centralized.

This section was drafted. Shenyang Transformer Research Institute, China Electronics Standardization Institute, the Ministry of Industry Institute of Electronics fifth quality inspection

Test center, Shanghai Quality Supervision, Inspection Technology Research Institute of electrical and electronic household appliances quality inspection.

This part drafter. Zhang Xianzhong, Luo Zu Wei, Zhang Lili, He Guofeng, Yu Yimin, Zhang Hong.

This section replaces the following previously issued as follows.

--- GB 19212.8-2006.

Power transformers, power supplies, reactors and similar products

Safety - Part 8. transformers for toys and

Particular requirements and tests of power

1 Scope

GB 19212.1-2008 This clause is replaced by the following.

GB 19212 This section specifies the safety requirements for toys and power transformers, for example, on electrical safety, temperature and mechanical aspects

Full regulations.

This section applies to toys, toy transformers and power transformers and interior electronics. This does not apply to a predetermined change to the

Pressure and the external circuit components and the power supply input and output terminals of the receptacle connector or output.

This section applies Stationary or mobile, single-phase, air-cooled (air-cooled or self-cooling) transformers for toys and interior transformers for toys

Power, which does not exceed the rated supply voltage of AC 250V, rated supply frequency and internal operating frequency of no more than 500Hz, not exceeding the rated output

Over 200VA, rated output current does not exceed 10A.

This section applies to special-purpose transformer and the isolation transformer.

This section applies to dry-type transformers for toys, which winding may be encapsulated or non-encapsulated type.

Toys for transformers and power transformer interior toys, load output voltage which is not more than 33V AC, or, on the interior Toys

Power supply transformer, which does not exceed the no-load output voltage ripple free DC 46V. Toys and power transformers, the rated output voltage

Not more than AC 24V, or toys power supply, the output voltage does not exceed the rated ripple free DC 33V.

This section is generally not considered children playing with toys with built-in transformer and toys specific safety problems with the power transformer.

Note 1. Note the following.

--- scheduled use of the transformer on a vehicle, ship or aircraft, may require some additional requirements (according to other applicable standards, national procedures, etc.);

--- avoid housing and housing components affected by the impact of external protection measures such as mold, insects, termites, solar radiation, and icing should also be considered;

--- transformer transport, storage and different working conditions should also be considered;

--- scheduled to be used for special circumstances, such as transformers for tropical environment, you can use additional comply with other applicable standards and national rules of order

Claim.

Note 2. With future development of transformer technology, may have to increase the upper limit frequency, but before then, this part may be used as guidelines.

2 Normative references

In addition to these references, GB 19212.1 of this chapter apply.

The chapter add the following references.

IEC 60227-1 rated voltage of 450/750V and chloride insulated cables - Part 1. General Requirements

(Polyvinylchlorideinsulatedcablesofratedvoltagesuptoandincluding450/750V-Part 1. General

requirements)

IEC 60245-1 rated voltage of 450/750V rubber insulated cables and below Part 1. General Requirements (Rubberinsu-

latedcables-Ratedvoltagesuptoandincluding450/750V-Part 1. Generalrequirements)

3 Terms and Definitions

In addition to the following, safety Part 1 GB 19212.1-2008 power transformers, power supplies, reactors and similar products. General

Requirements and tests (IEC 61558-1.2005, IDT) of this chapter apply.

The chapter paragraph 3 to read.

As used hereinafter, the term "transformer" means. if applicable, the power supply comprising a transformer with transformer toys and toy interior.

The chapter following is added.

3.1.101

Transformers for toys transformersfortoys

It is designed to power the toy, but not fixed to the toy or toys loaded into, does not exceed the rated output voltage of 24V AC independently Ann

Full isolation transformer.

3.1.102

Toys Power powersuppliesfortoys

Not fixed to the toy or toys loaded in, the output voltage does not exceed the rated AC 24V or 33V DC ripple built-Toys

A power transformer.

4 General requirements

This chapter applies the GB 19212.1-2008.

General description of the tests 5

This chapter applies the GB 19212.1-2008.

6 Ratings

GB 19212.1 of the chapter is replaced by the following.

6.101 pairs and power transformers, the output voltage should not exceed the rated AC 24V, the power supply, the output voltage should not exceed the rated ripple linear

Stream 33V.

8 Marking and other information

In addition to the following, GB 19212.1-2008 This clause applies.

8.1h items) Add the following content.

Transformer shall be marked with one of the graphical symbols shown in 8.11.

8.1n) item be amended as follows.

Outdoor transformer should be labeled with the corresponding IP code.

9 Protection against electric shock

In addition to the following, GB 19212.1-2008 This clause applies.

11 load output voltage and output current

In addition to the following, GB 19212.1-2008 This clause applies.

That section 11.1 is replaced by the following.

When the rated supply voltage transformer connected to the rated frequency, and with a lower energy (AC) rated output voltage and rated power factor

An impedance load for the rated output, the output deviation of the output voltage to the rated voltage value, the AC should not exceed 10% or, for

DC should not exceed 15%.

This requirement applies to all of the output winding and the tap.

Load output voltage 12

In addition to the following, GB 19212.1-2008 of this chapter apply.

The chapter increased the following provisions.

13 short-circuit voltage

GB 19212.1-2008 This clause does not apply.

14 fever

In addition to the following, GB 19212.1-2008 This clause applies.

Table 1 modified as follows.

Replaced with the following Table 1 on the outside of the housing all the requirements.

Parts temperature/°C

Outer housing (small test shown in Fig means can reach to 101), the hand

Handles and similar parts, if it is.

- made of metal;

- made of other materials.

Outer housing (small test shown in Fig means 101 is not touched).

15 short-circuit and overload protection

In addition to the following, GB 19212.1-2008 This clause applies.

16 Mechanical strength

In addition to the following, GB 19212.1-2008 This clause applies.

17 to prevent dust, harmful solid objects and moisture into the protection

This chapter applies the GB 19212.1-2008.

18 insulation resistance, dielectric strength and leakage current

This chapter applies the GB 19212.1-2008.

19 structure

In addition to the following, GB 19212.1-2008 of this chapter apply.

GB 19212.1-2008 19.1 replaced by the following.

19.1 input and output circuits to be electrically isolated from each other. There can be no direct or indirect structure should be made between these circuits

Except when you intend to take by connecting the other conductive parts.

By visual inspection and measurement, taking into account the provisions of Chapter 18 and Chapter 26 to verify eligibility.

19.1.1 between the input winding and the output winding insulation should be made at least double insulation or reinforced insulation configuration. Further, the input winding and the shell

Between the insulating member, the insulation between the output winding and the housing should be composed of double insulation or reinforced insulation.

19.1.2 are not connected to the housing and having at the input the intermediate conductive member (e.g., core) between the windings and the output winding of the transformer,

Intermediate insulation between the conductive member and the input winding, the intermediate insulation between the conductive member and the output winding insulation should be composed of at least substantially.

NOTE. There is at least substantially insulated with input winding, output winding or housing spaced from the intermediate conductive member, and related components may be considered to be connected.

In addition, after the insulation between the input winding and the output winding of the intermediate conductive members should be double or reinforced insulation configuration; after the

Interlayer insulating insulation between the output winding and the housing between the housing and the input winding of the conductive member should be constituted of double or reinforced insulation.

20 components

In addition to the following, GB 19212.1-2008 This clause applie...