GB/T 14048.17-2008Low - Voltage switchgear and controlgear - Part 5 - 4 : Control circuit devices and switching elements - Methord of assessing the performance of low - energy contacts - Special tes (English PDF)
低压开关设备和控制设备 第5-4部分:控制电路电器和开关元件 小容量触头的性能评定方法 特殊试验
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 14048.17-2008 in 30 minutes.
Issued by
Standardization Administration of China
Level / Type
National · Recommended
Issue date
December 30, 2008
Implementation date
October 1, 2009
Scope
GB/T 14048.17-2008 is the English-translated version of 低压开关设备和控制设备 第5-4部分:控制电路电器和开关元件 小容量触头的性能评定方法 特殊试验.
GB/T 14048.17-2008 — This section applies to independent contacts using categories under consideration for use as a control circuit switching elements.
This section considers the rated voltage are two cases. a) possible contacts for switching loads with electro-erosion, such as a programmable controller input, rated voltage is greater than or equal to 10V (Typically 24V); b) negligible electric corrosion situations, such as electronic circuits, the rated voltage is less than 10V (typically 5V).
This section does not apply to a very small capacity measurements used contacts, such as sensors or thermocouple system.
The purpose of this section is to identify a small-capacity contact performance assessment methods, give the following information. ---definition; General principles --- test method, the test is used to monitor and record each operation contact action; --- Conventional test equipment defined functional basis; --- Test preferred value; --- Specific occasion (such as a PC input switching) the special contact with the test conditions; --- Test report the information to be given; Explanations and justifications --- test results.
Found what you need?
Document preview — GB/T 14048.17-2008
National Standard of the People's Republic of China
- ICS
- 29.130.20
- Classification
- K 32
Issued by: Standardization Administration of China
Contents
- Preface
- 1 Scope and purpose
- 2 Normative references
- 3 Terms and definitions, symbols
- 4 Fundamentals
- 5 5 General test methods
- 6 General characteristics
- Characterization of defects 7
- 9 8 environmental conditions
- 9 Report
- 10 Test report provides information
- Appendix A (normative) information provided by the manufacturer
- References
Foreword
"Low-voltage switchgear and control equipment" currently consists of the following 18 sections.
--- GB 14048.1 low-voltage switchgear and control equipment Part 1. General;
--- GB 14048.2 low-voltage switchgear and control equipment Part 2. Circuit Breaker;
--- GB 14048.3 low-voltage switchgear and control equipment - Part 3. Switches, disconnectors, switch and fuse combination Appliances;
--- GB 14048.4 low-voltage switchgear and control equipment, electromechanical contactors and motor starters;
--- GB 14048.5 low-voltage switchgear and control equipment Part 5-1. Control circuit devices and switching elements - Electromechanical control Electrical circuit;
--- GB 14048.6 low-voltage switchgear and control equipment Part 4-2. Contactors and motor starters - AC semiconductor Motor controllers and starters (including soft starter);
--- GB/T 14048.7 low-voltage switchgear and control equipment Auxiliary equipment Section 1. Terminal blocks for copper conductors;
--- GB/T 14048.8 low-voltage switchgear and control equipment Ancillary equipment Section 2. Protective conductor terminal blocks for copper conductors Sub-row;
--- GB 14048.9 low-voltage switchgear and control equipment Part 6-2. Multiple function equipment (equipment) control and protection switch Electric (equipment) (CPS);
--- GB/T 14048.10 Low-voltage switchgear and control equipment, control circuit devices and switching elements - Part 2. close switch;
--- GB/T 14048.11 voltage switchgear and control equipment Part 6. Multiple function equipment - Section 1. Automatic transfer switch Appliances;
--- GB/T 14048.12 voltage switchgear and control equipment Part 4-3. Contactors and motor starters, non-powered LOADED AC semiconductor controllers and contactors;
--- GB/T 14048.13 voltage switchgear and control equipment Part 5-3. Control circuit devices and switching elements in it Proximity Switch (PDF) required to have under fault conditions to determine the function;
--- GB/T 14048.14 voltage switchgear and control equipment Part 5-5. Control circuit devices and switching elements having Mechanical latching function electrical emergency braking device;
--- GB/T 14048.15 voltage switchgear and control equipment Part 5-6. Control circuit devices and switching elements proximity Sensors and switching amplifiers DC Interface (NAMUR);
--- GB/T 14048.16 voltage switchgear and control equipment - Part 8. rotary motor control with built - in thermal protection (PTC) Unit;
--- GB/T 14048.17 voltage switchgear and control equipment Part 5-4. Control circuit devices and switching elements of small capacity Special tests evaluating the performance of the amount of contact;
--- GB/T 14048.18 voltage switchgear and control equipment Part 7-3. Ancillary fuse terminal blocks Safety requirements.
This part is the "low-voltage switchgear and control equipment" in Section 17.
This section identical with IEC 60947-5-4:2002 "low-voltage switchgear and control equipment Part 5-4. Control circuit devices and open Small-capacity switching element contacts assessing the performance of special test "(in English).
This section of Appendix A normative appendix.
This part is proposed by the China Electrical Equipment Industrial Association.
GB/T 14048.17-2008/IEC 60947-5-4:2002 the low-voltage electrical part by the National Standardization Technical Committee (SAC/TC189) centralized.
This section is responsible for drafting unit. Shanghai Electrical Apparatus Research Institute (Group) Co., Ltd.
1 Scope and purpose
This section applies to independent contacts using categories under consideration for use as a control circuit switching elements.
This section considers the rated voltage are two cases.
a) possible contacts for switching loads with electro-erosion, such as a programmable controller input, rated voltage is greater than or equal to 10V (Typically 24V);
b) negligible electric corrosion situations, such as electronic circuits, the rated voltage is less than 10V (typically 5V).
This section does not apply to a very small capacity measurements used contacts, such as sensors or thermocouple system.
The purpose of this section is to identify a small-capacity contact performance assessment methods, give the following information.
---definition;
General principles --- test method, the test is used to monitor and record each operation contact action;
--- Conventional test equipment defined functional basis;
--- Test preferred value;
--- Specific occasion (such as a PC input switching) the special contact with the test conditions;
--- Test report the information to be given;
Explanations and justifications --- test results.
2 Normative references
The following documents contain provisions which, through reference in this text, constitute provisions of this part. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this section, however, encourage the parties to this part of the research agreement Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
GB/T 2421-1999 Environmental testing for electric and electronic products - Part 1. General (idt IEC 60068-1. 1988) GB/T 2423 (all parts), Environmental testing for electric and electronic products Part 2. Test methods (IEC 60068-2 (all parts)) GB/T 5080.6-1996 Equipment reliability testing constant failure rate assumption validation (idt IEC 60605-6. 1989) GB 14048.1-2006 Low-voltage switchgear and control equipment Part 1. General (IEC 60947-1:2001, MOD) GB 14048.5-2001 Low-voltage switchgear and control equipment Part 5-1. Control circuit devices and switching elements - Electromechanical Control circuit devices (eqv IEC 60947-5-1:1997) GB/T 15969.2-2008 Programmable Controllers Part 2. Equipment requirements and tests (IEC 61131-2:2007, IDT)
3 Terms and definitions, symbols
3.1 Terms and Definitions
The following terms and definitions apply to this section.
In this section, as applicable, the term "time interval" can be expressed as "operating cycles." 3.1.1
Note 1. generally assumed as a starting point in the time interval, the product is in a state to perform a required function.
GB/T 14048.17-2008/IEC 60947-5-4:2002
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 2421-1999Environmental testing - General and guidance
- GB/T 15969.2-2008Programmable controllers - Part 2: Equipment requirements and tests
IEC 60068 · GB/T 2423 · GB/T 5080.6-1996 · IEC 60605 · GB 14048.1-2006 · IEC 60947 · GB 14048.5-2001 · IEC 61131
How to Download GB/T 14048.17-2008
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 2423.1-2008 — Environmental testing for electric and electronic products - Part 2: Test methods - Tests A: Cold
GB/T 2423.10-2019 — Environmental testing - Part 2: Test methods - Test Fc: Vibration (sinusoidal)
GB/T 2423.101-2025 — Environmental testing - Part 2: Test methods - Test: Inclinations and swings
Secure payment via Stripe
Payments accepted
GB/T 14048.17-2008
$225.00