GB/T 12668.701-2012Adjustable speed electrical power drive systems -- Part 701: Generic interface and use of profiles for power drive systems -- Interface definition (English PDF)

Foreword

GB/T 12668 "speed electric drive systems" is divided into the following sections.

--- Part 1. General requirements for low-voltage DC speed electric drive systems rating requirements;

--- Part 2. General requirements for low-voltage adjustable frequency ac power drive systems rating requirements;

--- Part 3. EMC requirements and specific test methods;

--- Part 4. General requirements AC voltage 1000V or more but not exceeding 35kV AC rated speed electric drive systems A predetermined value;

--- Part 5. Safety requirements;

--- Part 6. Determine the type of load duty and corresponding current ratings guidelines;

--- Part 7. PDSs common interface specification and use;

--- Part 8. power supply voltage Interface specification.

This section GB/T 12668 Part 701.

This section drafted in accordance with GB/T 1.1-2009 given rules.

This section uses the translation method identical with IEC 61800-7-1:2007 "Adjustable speed electrical power drive systems - Part 701. Electrical Transmission Use common interface and interface definitions. " Consistency correspondence between this part of international documents and normative references of our files are as follows.

GB/T 20540.5-2006 Digital data communication for measurement and control - Fieldbus for use in industrial control systems Type 3.

PROFIBUS specification - Part 5. Application layer service definition (IEC 61158-5-3:2003, MOD) GB/Z20541.1-2006 Digital data communication for measurement and control - Fieldbus for use in industrial control systems Type 10.

PROFINET Specification - Part 1. Application layer service definition (IEC 61158-5-10:2003, MOD) GB/Z20541.2-2006 Digital data communication for measurement and control - Fieldbus for use in industrial control systems Type 10.

PROFINET Specification - Part 2. Application layer protocol specification (IEC 61158-6-10:2003, MOD) this section makes the following editorial changes.

--- Deleted international standards foreword;

--- The introduction of international standards-based conversion section Introduction;

--- International Standard 3.2.20 unnumbered and related content, this part of the corresponding reg number has been adjusted;

--- International Standards Normative documents referenced in the chapter of the IEC 61800-7-1 itself, the normative references in this section to remove the document.

This part is proposed by the China Electrical Equipment Industrial Association.

This part of the National Science Power Electronics Standardization Technical Committee (SAC/TC60) centralized.

This section is drafted. Tianjin Electric Drive Design Institute, Shandong Taikai Automation Co., Ltd., Haileinuoer Technology Co. Shares the companies hope Senlan Technology Co., CISDI Electrical Technology Co., Ltd., Shenzhen marks the New Technology Co., Ltd., North Beijing Leader & Harvest Electric Technologies Co., Ltd., Shenzhen INVT Electric Co., Ltd., Beijing Hiconics Inverter Technology Company Limited Division of Harbin Jiuzhou Electric Co., Ltd., Shandong scenery of Electronic Science and Technology Development Co., Ltd., Shanghai and Australia-Vail Power Electronics Co., Division of ABB Beijing Drive Systems Co., Ltd., the state-controlled electricity distribution equipment Quality Supervision and Inspection Center.

Introduction

GB/T 12668 "speed electric drive systems" provides a set speed electric drive systems - Generic specification.

National standard "speed electric drive systems." This section describes a common interface between the control system and electric drive systems.

This interface can be embedded in the control system, the control system itself is also located on the actuator (sometimes called "drive-sensitive" or "smart drive").

A variety of physical interfaces are available (both analog and digital inputs and outputs, serial and parallel interfaces, fieldbus and network). Correct in some application areas (for example. motion control) and device class (for example, a conventional drive (device), locator), a particular physical interface specification has been it has been determined. Related drive and controller interface of the application is installed on, is protected by trademark and vary widely.

This section provides a common drive control functions, parameters, and a description of the state machine or image sequence run to the drive specification.

This section provides a method and data transmission function, the method does not depend on the transmission specifications and communication interfaces have been used.

Its object is the transmission mode with one kind of common functions and devices for different communication interfaces. This allows for the transmission operation without any known Knowledge of the control to provide motion control (or speed control or transmission control applications) common operations possible.

Define common interface from several different angles.

For manufacturers gearing

--- Easier to support systems integrators;

--- General terms, easier to describe the transmission function;

--- Transmission does not depend on the choice of special support.

For control unit manufacturer

--- No Effect bus technology;

--- Simple means of integration;

--- Do not depend on the drive supplier.

For system integrators

--- Means integration easier;

--- Only a rational modeling method;

--- Not dependent on bus technology.

Design with several different transmission control systems and specialized motion control applications require a lot of effort. Execution system software and Understand the function of each component of the task may run out of engineering resources. In some cases, the drive means do not share a physical interface. one these control means merely support an interface, this interface is not supported by specific gearing. On the other hand, functions and data structures are often it is clearly incompatible. In this case, to the application software, system integrators need to write a specific interface, but this should not be their responsibility.

In the existing structure, some applications require the interchangeability of devices or new devices integrated. Therefore, their solution is mutual contradictory. Workaround transmission line with the specific requirements and specifications may manufacturers are incompatible; for the selected unit will reduce the selection of the most the degree of freedom for this application device. This unit must be applied to a particular physical interface, while being supported by the control device.

This section is divided into a common interface portion of FIG. 1 and several appendices. For model CiA4021), CIPMotionTM2),

1) CiA402 (CANinAutomation abbreviation) is a trademark of automation controller LAN. This information is provided for the convenience of users of international standards, Would not constitute endorsement by the IEC for the trademark holder or any of its products. Comply with this specification does not require the use of CiA402 trademark.

2) CIPMotionTM is a trademark of Open DeviceNet Vendor Association. This information is provided for the convenience of users of international standards, not by the IEC for the business Mark holder or any of their goods constitute endorsement. Comply with this specification does not require the use of CIPMotionTM trademark. CIPMotionTM need to use the trademark License PROFIBUS international organizations.

12) PROFINET are trademarks of PROFIBUS International. This information is provided for the convenience of international standard user, not as a trademark held by the IEC People or any of their goods constitute endorsement. Comply with this specification does not require the use of PROFINET trademark. Use of a trademark, PROFINET PROFIBUS license.

FIG. 1 GB/T 12668 Structure "speed electric drive systems" Part 7

Speed \u200b\u200belectric drive systems Part 701. Electric Drive Systems Use common interfaces and interface definitions

1 Scope

This section provides application specification PDSs, and by using a common interface model description of its current communication system Image.

This function is not part of the provisions intended to ensure functional safety. According to relevant standards, agreements and legal functions need to take additional safety Measures.

This section applies to electrical drive systems (PDS) with a common interface control unit application control between programs. The PDS is not common interface Specific to any particular communication network technology. Appendix to this part of the detailed specifications of the different gear used in PDS common interface.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document.

IEC 61158-5-2 Industrial communication networks - Fieldbus specifications - Part 5-2. Application layer service definition - Type 2 elements (Industrialcommunicationnetworks-Fieldbusspecifications-Part 5-2. Applicationlayerservicedefi-nition-Type2elements) IEC 61158-5-3 Industrial communication networks - Fieldbus specifications - Part 5-3. Application layer service definition - Type 3 elements (Industrialcommunicationnetworks-Fieldbusspecifications-Part 5-3. Applicationlayerservicedefi-nition-Type3elements) IEC 61158-5-10 Industrial communication networks - Fieldbus specifications - Part 5-10. Application layer service definition - Type 10 elements (Industrialcommunicationnetworks-Fieldbusspecifications-Part 5-10. Applicationlayerservice definition-Type10elements) IEC 61158-6-2 Industrial communication networks - Fieldbus specifications - Part 6-2. Application layer protocol specification - Type 2 elements (Industrialcommunicationnetworks-Fieldbusspecifications-Part 6-2. Applicationlayerprotocol specification-Type2elements) IEC 61158-6-3 Industrial communication networks - Fieldbus specifications - Part 6-3. Application layer protocol specification - Type 3 elements (Industrialcommunicationnetworks-Fieldbusspecifications-Part 6-3. Applicationlayerprotocol specification-Type3elements) IEC 61158-6-10 Industrial communication networks - Fieldbus specifications - Part 6-10. Application layer protocol specification - Type 10 elements (Industrialcommunicationnetworks-Fieldbusspecifications-Part 6-10. Applicationlayerprotocol specification-Type10elements) IEC 61800-7 (all parts) speed electric drive systems and electric drive systems using common interface specification (Adjustable speedelectricalpowerdrivesystems-Genericinterfaceanduseofprofilesforpowerdrivesystems) IEC 61800-7-201 speed electric drive systems - Part 7-201. Electrical Transmission and use a common interface specification Type 1 specification (Adjustablespeedelectricalpowerdrivesystems-Part 7-201. Genericinterfaceanduse