Valid

T/CSAE 63-2017Electromagnetic compatibility test methods and requirements of electric components and subsystems (12v) of vehicle (English PDF)

汽车电器零部件及子系统(12V)电磁兼容性能测试方法及要求

Preview PDF

This is a limited preview

Buy now to download the full PDF (44 pages)

Need quotation for your management?

Get a formal quotation for T/CSAE 63-2017 in 30 minutes.

Issued by

China Society of Automotive Engineers

Level / Type

National · Mandatory

Issue date

November 3, 2017

Implementation date

November 3, 2017

Scope

T/CSAE 63-2017 is the English-translated version of 汽车电器零部件及子系统(12V)电磁兼容性能测试方法及要求.

T/CSAE 63-2017 — This standard applies to electromagnetic compatibility (EMC) test methods, test procedures and requirements for all 12V electrical components and subsystems of automobiles.

The contents of this standard can be used as a reference for the vehicle manufacturer or component company to develop a test plan. The optional test grades or limits given by each test reflect the level required by domestic mainstream automakers, and the specific requirements are determined by the vehicle manufacturer.

The technical requirements for conducted or conducted immunity included in this standard are limited to low voltage DC components. High voltage systems (such as hybrid vehicles, plug-in hybrid vehicles, pure electric vehicles) are not included in this standard.

The specific application is shown in Table 5-1. The purpose of this standard is to ensure the EMC performance of the vehicle.

Found what you need?

Document preview — T/CSAE 63-2017

National Standard of the People's Republic of China

ICS
43.120
Classification
T 09

Issued by: China Society of Automotive Engineers

Contents

  • Foreword
  • 1 Scope
  • 1.1 Scope description
  • 1.2 Application Notes
  • 2 Normative references
  • 3 Terms and definitions, abbreviations and symbols
  • 3.1 Terms and definitions
  • 3.2 Abbreviations
  • 3.3 Symbols
  • 4 General test requirements
  • 4.1 General
  • 4.2 Functional importance classification
  • 4.3 Performance Level Classification
  • 4.4 Load simulator
  • 4.5 Artificial Network
  • 4.6 Harness Requirements
  • 4.7 Grounding requirements
  • 4.8 Test conditions
  • 4.8.1 Tolerance
  • 4.8.2 Test environmental conditions
  • 4.8.3 Power
  • 5 Classification and requirements
  • 6 Radiated emissions
  • 6.1 Reference standards
  • 6.2 Test purpose and scope
  • 6.3 Test methods
  • 6.3.1 Test arrangement
  • 6.3.2 Test procedure
  • 6.4 Test requirements
  • 7 RF conducted emissions
  • 7.1 Reference standards
  • 7.2 Test purpose and scope
  • 7.3 Test methods
  • 7.3.1 Test arrangement
  • 7.3.2 Test procedure
  • 7.4 Test requirements
  • 8 Magnetic field emission
  • 8.1 Reference Standards

Foreword

This standard is used as a quality control standard for automobile parts and components to ensure product quality and meet quality requirements after loading.

This standard categorizes car components in detail, and specifies the performance requirements for various types of components.

Conducted emission performance to ensure the good operation of the vehicle receiver. The radio frequency, conducted, and electrostatic discharge immunity performance is specified to ensure zero the safety level of the component. Specify test methods and limits for each emission test, test methods, test levels, Performance criteria. It also stipulates the running status of each product during testing to ensure that it can meet the requirements under severe conditions. in case Under specific working conditions, the special performance requirements and quality requirements index values need to be obtained from production experience accumulation, which can be obtained by manufacturers and After the auto company negotiates, the application of the standard is modified. This standard is prepared in accordance with the rules given in GB/T 1.1-2009.

This standard was approved by the Chinese Society of Automotive Engineers.

This standard was first issued in November.2017.

This standard was drafted. Shanghai Electric Research Institute, Chongqing Changan Automobile Co., Ltd., Shanghai Automobile Group Co., Ltd.

Company passenger car company, BYD Automobile Industry Co., Ltd., Zhejiang Geely Automobile Research Institute Co., Ltd., Chery Automobile Co., Ltd.

Division, Chery Commercial Vehicle (Anhui) Co., Ltd., Great Wall Motor Co., Ltd., Zotye New Energy Vehicle Co., Ltd., Shanghai Shishi Automobile Technology Co., Ltd., Beijing Automotive Research Institute Co., Ltd., Beijing New Energy Automobile Co., Ltd.

Drafters. Zheng Junqi, Liu Yuan, Li Xu, Yue Qingyu, Ma Qian, Zhou Yukui, Zhu Liming, Li Chuan, Wang Hongwu, Wang Yuchuan, Geng Huiyong, Ma Conghai, Quan Xiangni, Guo Dijun, Tian Yongpo, Pu Yuansheng, Tang Wei, Zhang Qingqing, Gao Xinjie.

Author. Liu Yuan.

14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 5.2017/11/7 9.58.41 14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 6.2017/11/7 9.58.41 14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 1.2017/11/7 9.58.41 file. For undated references, the latest version (including all amendments) applies to this document.

GB/T 18655-2010 Vehicles, ships and internal combustion engines Radio disturbance characteristics Limits and measurement methods for protecting on-board receivers GB/T 21437.1-2008 Road vehicles. Electrical disturbances caused by conduction and coupling. Part 1. Definitions and general description GB/T 21437.2-2008 Road vehicles. Electrical disturbances caused by conduction and coupling. Part 2. Electrical transients along power lines Conduct GB/T 21437.3-2012 Road vehicles. Electrical disturbances caused by conduction and coupling. Part 3. Conductors other than power lines Electrical transient emission through capacitive and inductive coupling GB/T 6113.101-2008 Specification for radio disturbance and immunity measuring equipment and methods-Part 1-1. Radio disturbance Noise and immunity measurement equipment GB/T 33014.1-2016 Road vehicles. Test method for immunity of electrical/electronic components to narrowband radiated electromagnetic energy. Part 1 Section. General provisions GB/T 33014.2-2016 Road vehicles. Test method for immunity of electrical/electronic components to narrowband radiated electromagnetic energy. Part 2 Part. Anechoic Chamber Method GB/T 33014.3-2016 Road vehicles. Test method for immunity of electrical/electronic components to narrowband radiated electromagnetic energy. Part 3 Section. Transverse Electromagnetic Wave (TEM) Chamber Method GB/T 33014.4-2016 Road vehicles. Test method for immunity of electrical/electronic components to narrowband radiated electromagnetic energy Part. Large Current Injection (BCI) method GJB 151B-2013 Military equipment and subsystems Electromagnetic emission and sensitivity requirements and measurements ISO 11451-3.:2007 Road vehicles-Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy-Part 3. On-board transmitter simulation ISO 11452-1.:2008 Road vehicles-Component test methods for electrical disturbances from narrowband radiated electromagnetic energy-Part 1. General principles and terminology ISO 11452-8.:2008 Road vehicles-Component test methods for electrical disturbances from narrowband radiated electromagnetic energy-Part 8. Immunity to magnetic fields ISO 11452-9.:2012 Road vehicles-Component test methods for electrical disturbances from narrowband radiated electromagnetic energy-Part 9. Portable transmitters ISO 10605.:2008 Road vehicle-Test methods for electrical disturbances from electrostatic discharge ECE R10.REV5.0.2015 Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions

3 Terms and definitions, abbreviations and symbols

3.1 Terms and definitions

The terms and definitions defined in GB/T 4365 and GB/T 29259 apply to this document.

3.1.1

Acceptance criteria

Defines the margin of deviation of allowed functional performance of equipment under electromagnetic interference.

3.1.2

Active electronic module 14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 2.2017/11/7 9.58.41 an electronic module that operates using digital or analog circuits (including microprocessors, operational amplifiers, memory devices).

3.1.3

Artificial network (AN) A device used to provide a known impedance to the DUT power cord.

3.1.4

Bulk current injection (BCI) Method for coupling RF current into a wiring harness.

3.1.5

Component

A collective name for active electronic modules, motors, and passive and inductive devices.

3.1.6

Control circuits

Input/output circuits connected to vehicle batteries via switches, relays, or resistive/inductive loads.

Directly fed in, or by a battery with a switch.

3.1.7

Component, subsystem engineering specification Specification of all performance requirements of components or subsystems (mechanical, temperature, electromagnetic compatibility, etc.).

3.1.8

Disturbance

Any electrical transients or electromagnetic phenomena that may affect the correct operation of electrical/electronic equipment.

3.1.9

DUT device (s) under test (DUT) any electrical or electronic component, module, motor, filter, etc. being tested.

3.1.10

ESD-air discharge

The test method of completing the discharge action by placing the electrode of the electrostatic generator close to the device under test and discharging an arc to the device under test.

3.1.11

ESD-contact discharge First, contact the electrode of the electrostatic generator with the device under test, and then press the switch on the generator to discharge the device to the device under test.

Test Methods.

3.1.12

Memory function (temporary or permanent) Means computer memory used for, but not limited to, software code, engine calibration data, driving habits, and initial receiver settings, 14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 3.2017/11/7 9.58.41 14220-Test methods and requirements for electromagnetic compatibility performance of automotive electrical parts and subsystems (12V) .indd 4.2017/11/7 9.58.41 14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 5.2017/11/7 9.58.41 There are more stringent requirements.

The following is an example of Class C functionality.

a) Directly control the relevant functions of the vehicle, such as the engine, transmission, brakes, suspension, power steering system, speed limiter Control functions such as position control; the function of controlling the driver's position (including the position of the seat or steering wheel); controlling the effects of low beams, wipers, etc.

The function of the driver's field of vision.

b) Functions that protect drivers, passengers and other road users, such as airbags and safety restraint systems.

c) Visual signal function and sound signal function. Visual signal functions, such as. turn signals, brake lights, position lights, rear position lights, Hazard warning light indicators, and warning indicators, lights, or displays related to Class A and B functions; sound signal functions, such as burglar alarms, horns, etc.

d) Functions related to the vehicle data bus.

e) Functions related to important vehicle indicator data, such as speedometer, driving recorder, tachometer.

4.3 Performance level division

When the function of the device under test is disturbed, its degree of function realization is divided into the following five levels.

a) Category I. During and after the harassment, can perform all its pre-designed functions normally;

b) Category II. During the period of harassment, it can perform all its pre-designed functions, but one or more indicators may exceed the regulations.

After the harassment stops, all functions automatically return to normal, and the storage function always maintains a normal level;

c) Category III. During the harassment, one or more of its pre-designed functions cannot be performed, but after the harassment ceases, the Return to normal

d) Category IV. During the period of harassment, one or more of its pre-designed functions cannot be performed.

Reset operation to restore the normal state;

e) Category V. During and after the harassment, one or more of its pre-designed functions cannot be performed, and the it returns to normal and must be repaired or even replaced.

4.4 Load Simulator

The role of the load simulator is to make the DUT work normally, and at the same time provide convenient conditions for DUT testing. The load simulator should be built Consider the following.

-The load simulator is a shielded housing (see Figure 1) that contains the external electrical interfaces (such as sensors, loads, etc.) of the DUT common equipment

3), which is the support and monitoring equipment of the test process, and also serves as the radio frequency boundary of the DUT harness;

-Load simulators should be built as much as possible with the components used for production, which are important for inductance and pulse width modulation (PWM) circuits are particularly important. If this is not possible, the simulated load should accurately represent the actual resistance, capacitance and inductance in the actual car.

Do not use a simple resistive load unless it is proven to exist in real vehicle equipment;

-If the DUT's power comes from other electronic modules (such as sensors), the load simulator should accurately reflect the module's power Current limit-If the load simulator contains active devices, appropriate measures should be taken to prevent it from potentially affecting auxiliary equipment during testing, or affect the radiation emission test results;

-All simulated loads in the load simulator should be grounded with reference to the load simulator housing (Figure 1);

-In the test, the load simulator is not only the test load of the DUT, but also the key function of DUT operation and monitoring.

The interface of the auxiliary equipment needs to be tested. Therefore, all its inputs/outputs should use the power ground in the load simulator as a parameter the test ground is connected to the ground plane of the test bench by connecting the load simulator shell. When packaging stipulates partial connection it may not be applicable in the case of land;

14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 6.2017/11/7 9.58.41-Whenever possible, use fiber optics to connect DUT input/output signals and remote testing aids;

-The optical fiber frequency bandwidth should be selected reasonably to avoid coupling unwanted signals and the potential impact on test auxiliary equipment. in Under the premise of not affecting the test results, you can also use shielded cables instead of optical fibers, but load simulators and test laboratory walls Keep the distance between the walls as short as possible, and pay close attention to confirming that these cables will not affect the test results. Should be tested at EMC in the trial plan, record the configuration of these cables (such as routing, shield grounding, etc.);

-RF filters should be used to prevent monitoring/auxiliary equipment malfunction due to stray RF energy. Should be selected so as not to affect component operation, and RF filters that do not affect component performance during EMC testing. The capacitance of the RF filter should be recorded in the EMC test plan.

8 9 Ground

Explanation.

1--power supply; 4--insulated support (epsilonr <= 1.4);

2--artificial network; 5--sample under test DUT;

3-- metal shell of the load simulator (optional, needs to be well grounded); 6-- grounding plate;

3a--DUT load (reference power); 7--optical fiber;

3b--DUT load (refer to test bench shell); 8-- fiber optic interface;

3c--optical fiber interface (optional, can be set outside the test bench); 9-- auxiliary/monitoring equipment.

Figure 1 Schematic diagram of the load simulator layout

4.5 Artificial Network

Many of the tests in this standard require the use of artificial networks. The design and operating characteristics of the artificial network should follow GB/T 18655 or GB/T 21437.2. For tests that do not require the use of an artificial network, the power supply should be connected directly to the ground plane, load simulator, and DUT.

4.6 Harness requirements

Standard test cables should be used for the electrical connection between the DUT and the analog load. The type of cable should refer to the Cable (such as twisted pair). Some tests (such as conducted emissions) require the shortest possible power supply between the DUT and the analog load and Negative cable. In order to reduce the number of test cables, it is recommended to weld a single test cable to the quick connector so that it can be plugged in when needed in specific test circuits, and reduce cable length (such as coaxial connectors).

4.7 Grounding requirements

The artificial network should be connected to the ground plane of the test table. The ground resistance must be less than 2.5 mohm. Recommend the use of screws or other the low-impedance connection method connects the ground plane to the ground. The same applies when the DUT has a metal case. Grounding of the load simulator Requirements are based on actual vehicle conditions.

14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 7.2017/11/7 9.58.42 14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 8.2017/11/7 9.58.42 14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 9.2017/11/7 9.58.42 14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 10.2017/11/7 9.58.42 14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 11.2017/11/7 9.58.42 14220-Automotive electrical components and subsystems (12V) electromagnetic compatibility performance test methods and requirements.indd 12.2017/11/7 9.58.42 14220-Test methods and requirements for electromagnetic compatibility performance of automotive electrical parts and subsystems (12V) .indd 13.2017/11/7 9.58.43 14220-Automotive electrical components and subsystems (12...

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 44 pages — is available in the English PDF.

How to Download T/CSAE 63-2017

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
44 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

T/CSAE 63-2017

$530.00