Valid

T/CSAE 62-2017Hardware Interface Guidelines for the Vehicle Control Unit (English PDF)

整车控制器接口规范

Preview PDF

This is a limited preview

Buy now to download the full PDF (10 pages)

Need quotation for your management?

Get a formal quotation for T/CSAE 62-2017 in 30 minutes.

Issued by

China Society of Automotive Engineers

Level / Type

National · Mandatory

Issue date

September 18, 2017

Implementation date

September 18, 2017

Scope

T/CSAE 62-2017 is the English-translated version of 整车控制器接口规范.

T/CSAE 62-2017 — This standard specifies the hardware interface design specification for vehicle controllers for pure electric passenger vehicles. The purpose of this standard is to serve as the basis for the design of the vehicle controller within the enterprise.

Found what you need?

Document preview — T/CSAE 62-2017

National Standard of the People's Republic of China

ICS
43.120
Classification
T 47

Issued by: China Society of Automotive Engineers

Contents

  • Foreword
  • 3.4 SOC
  • 3.5 EMC
  • 3.6 EFT
  • 3.7 PWM
  • 3.8 RS232
  • 3.9 K_Line
  • 3.10 MOST
  • 3.11 FlexRay
  • 4 Hardware interface division
  • 5 Hardware interface specification
  • 5.1 Power Interface
  • 5.2 Activating the interface
  • 5.5 Digital Signal Interface

Foreword

The "Car Controller Interface Specification" stipulates the basic specifications of the hardware interface of the pure electric passenger vehicle controller.

The pure electric passenger vehicle controller provides a basis for the formation of a unified diagnosis and maintenance of the pure electric passenger vehicle industry in China.

standard.

This specification was proposed by the Strategic Alliance for Technology Innovation of the Electric Vehicle Industry.

This specification is under the jurisdiction of the China Automotive Engineering Society.

3.4 SOC

SOC. Fully referred to as the state of charge state of charge.

The SOC is used to reflect the remaining capacity of the battery energy, and its value is defined as the ratio of the remaining battery to the battery capacity.

3.5 EMC

EMC. Fully known as Electromagnetic Compatibility.

EMC is defined as "equipment and systems that function properly in their electromagnetic environment and do not constitute anything unbearable in the environment.

The ability of electromagnetic disturbance" This definition contains two aspects. First, the equipment should be able to work properly in a certain electromagnetic environment.

That is, the device should have a certain electromagnetic immunity; secondly, the electromagnetic disturbance generated by the device itself cannot be generated for other electronic products.

The big impact is electromagnetic disturbance.

3.6 EFT

EFT. Fully called electric fast transient, Electrical Fast Transient EFT technology is a hardware anti-interference technology, mainly for electrical fast transient burst interference signals.

3.7 PWM

PWM. full name pulse width modulation, Pulse-Width Modulation PWM is a pulse width variable signal that is a way to pass data signals.

3.8 RS232

RS232. Fully referred to as Recommendation No. 232, Recommended Standard RS232 is a serial communication protocol used in industrial control sites.

3.9 K_Line

K_Line. The K line is generally used in car detection systems and is a single-wire mode that connects to the controller and enables data transfer.

3.10 MOST

MOST. Media Oriented System Transport for Media

3.11 FlexRay

FlexRay. FlexRay is a high-speed, deterministic, fault-tolerant bus technology for automotive applications.

4 Hardware interface division

The electric vehicle controller collects driver driving instructions through the hardware interface, and obtains the motor and battery pack through the vehicle communication network.

Relevant information of components, analysis and calculation, sending management instructions to achieve vehicle drive control, energy optimization control, safety protection Protection and other functions. Based on the control function of the vehicle controller, the hardware interface of the vehicle controller can be divided into a power interface, a ground interface, and a drive.

Dynamic interface, digital signal interface, analog interface and communication interface.

5 Hardware interface specification

5.1 Power Interface

5.1.1 Input Power

The vehicle controller takes power from the low-voltage battery of the whole vehicle. The design specifications of the input power interface can refer to the parameter requirements of Table 1.

Table 1 Input power interface requirements

Interface name standby current support function Input power interface 9 v-16 v; leakage current less than 4 mA Monitoring low voltage battery voltage can support implementation Battery aging status detection function, prompt replacement low Press the battery, or control the DCDC relay the function provides an input signal.

5.1.2 Output Power

The vehicle controller can provide DC power output capability for vehicle sensor power supply. The specific solution is determined according to the system design.

The port design can refer to the requirements of Table 2.

Table 2 Output power interface design recommendations

Interface name parameter indicator support function Output power interface Provide 2 power output; each power channel Stream output capability >100 mA; voltage accuracy is higher than 2%; output power and controller chip power supply independent Power is supplied to an external sensor such as an accelerator/brake pedal.

5.2 Activating the interface

The vehicle controller can have an activation interface such as a key signal, a charging signal, a CAN signal, and a remote activation signal.

The system design determines that the interface design indicators can refer to the requirements of Table 3.

Table 3 Activation interface design recommendations

Interface name parameter indicator support function Key interface 9 v-16 v; can access 2 key signals Vehicle low-voltage electrical appliances up and down control; vehicle high Pressure system up and down control; motor system power on and off Control; after the key is powered off, such as motor /the battery is cooled down and the fault code is stored.

Charging interface

Slow charge and fast charge signal Two signals are activated separately Charging protection function to prevent vehicle error during charging process Action; vehicle charging power statistics function; charging the process lights up the necessary equipment such as the meter.

Table 6 High-side drive interface design recommendations

Interface name parameter indicator support function High-side relay drive interface Short circuit protection for power supply; short circuit protection for ground; over current Over temperature protection; can work under 16 V power Vehicle high voltage relay control.

5.4.3 LED driver

The vehicle controller can be equipped with LED lamp driving capability for fault prompting, etc. Figure 3 is a schematic diagram of the LED lamp driving interface.

The maximum drive capability depends on the load.

Drive and

Troubleshooting

led

Figure 3 LED light drive interface schematic

5.5 Digital Signal Interface

The vehicle controller should have a digital I/O interface that responds to the vehicle's switching signals. Switching signals can be divided into active high and low levels Effective two.

5.5.1 Digital Input

A schematic diagram of an active high digital input interface is shown in Figure 4. The Rpd high potential terminal should have overvoltage protection measures.

Rpd

Input

VGND

Input electricity

Flow direction

Pull-down resistor

Ideal op amp

Figure 4 digital input (switch high level) interface schematic

The schematic diagram of the active low digital signal input interface is shown in Figure 5.

Rpu

Input

VGND

VGN

Current direction

Pull-up resistor

Ideal op amp

Figure 5 digital input (switch low level) interface diagram

The recommended design specifications for the digital signal input interface are shown in Table 7.

Table 7 Digital Input Interface Design Suggestions

Interface name parameter indicator support function Hand brake switch Overvoltage protection; ESD protection;

9V-16V voltage range Auxiliary parking function, the vehicle is not allowed to move (forward/reverse) when the hand brake is working.

Brake pedal switch

Overvoltage protection; ESD protection;

9V-16V voltage range Brake energy feedback management.

Forward/neutral/reverse Overvoltage protection; ESD protection;

9V-16V voltage range Gear judgment function, set the current gear state of the vehicle, calculate the torque, can the volume management strategy provides an input signal; an input signal is provided for the reverse speed limit.

Minhang switch

Overvoltage protection; ESD protection;

9V-16V voltage range the state setting of the limp is the torque calculation and energy management strategy during the trip.

Can provide input signals.

High voltage allowable power switch Overvoltage protection; ESD protection;

9V-16V voltage range Determine whether the driver allows the vehicle to be powered on at high voltage, and can be used for vehicle attachment control, the input signal of the high-voltage power-on management of the whole vehicle.

Cruise switch

Overvoltage protection; ESD protection;

9V-16V voltage range Cruise function setting, providing torque calculation and energy management strategy for cruising input signal.

Note. Brake energy feedback management. Calculate the vehicle feedback energy by detecting the brake pedal switch signal and combining the current state of the battery and the motor.

5.5.2 PWM signal output

The vehicle controller provides a PWM signal output channel. The recommended design specifications are shown in the table below.

Table 8 PWM output design recommendations

Interface name parameter indicator support function PWM output interface 5V voltage; 1Hz-10KHz frequency range; 1% can be achieved Duty cycle step size adjustment Data transmission with electronically controlled air conditioning system, air conditioning Working power.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 10 pages — is available in the English PDF.

How to Download T/CSAE 62-2017

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
10 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

T/CSAE 62-2017

$195.00