T/CSAE 58-2017Test method for estimating average grain size of microalloying non-quenched and tempered steel and its products (English PDF)
非调质钢及其制品平均晶粒度检验方法
This is a limited preview
Buy now to download the full PDF (8 pages)
Need quotation for your management?
Get a formal quotation for T/CSAE 58-2017 in 30 minutes.
Issued by
China Society of Automotive Engineers
Level / Type
National · Mandatory
Issue date
November 3, 2017
Implementation date
November 3, 2017
Scope
T/CSAE 58-2017 is the English-translated version of 非调质钢及其制品平均晶粒度检验方法.
T/CSAE 58-2017 — This standard specifies the method for forming high temperature austenite grain size of non-quenched and tempered steel, and the actual grain size display and evaluation method for non-quenched and tempered steel products.
Found what you need?
Document preview — T/CSAE 58-2017
National Standard of the People's Republic of China
- ICS
- 43.120
- Classification
- T 40
Issued by: China Society of Automotive Engineers
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Test method for austenite grain size of non-quenched and tempered steel
- 4.1 Formation conditions of austenite grain size of non-quenched and tempered steel
- 4.2 Display and determination of essential grain size of non-quenched and tempered steel
- 5 Inspection method of actual grain size of non-quenched and tempered steel products
- 6 Grain Size Report
Foreword
In order to facilitate the evaluation of the austenite grain size growth tendency of non-quenched and tempered structural steel under forging heating or controlled cooling after forging, and non-quenching and tempering the actual grain size of steel rolling, forging, and forgings is specially formulated for this standard.
Compared with quenched and tempered steel parts, the austenite formation temperature of non-tempered steel forgings is higher, and the same austenite crystal as quenched and tempered steel is used.
The particle size formation temperature is inconsistent with the actual process state. Non-quenched and tempered steel rolled, forged or forged structures may be "flaky pearlite" "Ferrite", flake pearlite, low carbon martensite, granular bainite, etc. For the first two microstructure states, the evaluation of the actual grain size the method is not specifically stipulated in GB/T 6394-2002 "Method for determination of metal average grain size".
This standard complies with GB/T 6394-2002 "Method for Determining the Average Grain Size of Metals".
The production process and organizational characteristics are adapted.
Appendix A of this standard is a normative appendix.
This standard was proposed by the Material Branch of the Chinese Society of Automotive Engineers.
This standard was approved by the Chinese Society of Automotive Engineers.
This standard was first issued in November.2017.
This standard was drafted. Dongfeng Motor Corporation, China FAW Group Corporation, Jiangling Automobile Co., Ltd., Northeast Special Iron and Steel Co., Ltd., Jiangyin Xingcheng Special Steel Co., Ltd., Hubei Xinye Steel Co., Ltd., and Shougang Group Co., Ltd.
4 Test method for austenite grain size of non-quenched and tempered steel
4.1 Formation conditions of austenite grain size of non-quenched and tempered steel
The austenite grain size of non-quenched and tempered steel reflects the fine grain of non-quenched and tempered steel obtained under forging controlled cooling, controlled rolling controlled cooling or forging waste heat quenching the ability of organization should be the same as the original austenite that can be obtained stably before the non-quenched and tempered steel rolling or forgings undergo low temperature solid phase transformation after hot forming Grain size corresponds.
The external process factors affecting the austenite grain size of non-quenched and tempered steel in the use state include. forging heating temperature and holding time, Final forging temperature, deformation and deformation rate, cooling rate in high temperature area after forging (rolling), etc. In fact, in the hot rolling or forging Under the premise of force and efficiency, the process factors that can be used to refine the grain are usually only the cooling rate (time) in the high temperature region after forging (rolling) and Final forging (rolling) temperature; and under specific process conditions, the final forging (rolling) temperature and forging (hot rolling) heating temperature (1150 °C ~ 1250 °C) has a corresponding relationship, the former is generally 50 °C ~ 250 °C lower than the latter.
In order to facilitate the stability of the test conditions, the formation condition of the essential grain size of non-quenched and tempered steel is. it will be taken from raw materials, and the effective size is not large the sample at phi25 is heated to 950 °C ~ 1200 °C and held for 5 minutes to 15 minutes. The heating temperature corresponds to the final (rolling) forging temperature, the holding time corresponds to the cooling rate or time in the high temperature region after forging, the specific values of the heating temperature and the holding time and the forged (rolled) product the size is related to the forging process and is determined experimentally.
The location of the specimen to be cut shall be performed in accordance with the sampling position of tensile or impact specimens specified in GB/T 2975; the preparation of the specimen shall be in accordance with GB/T 13298 get on.
4.2 Display and determination of essential grain size of non-quenched and tempered steel
4.2.1 For the display of the intrinsic grain size of non-quenched and tempered steel, it is recommended to use the direct hardening method or the ferrite mesh method to fix the original austenite grain boundaries.
Direct hardening method. After austenitizing the sample under the conditions specified in 4.1, it is quenched at a cooling rate capable of being completely hardened to obtain martensite.
After being ground, polished and etched, the body structure shows the original austenite morphology which is completely hardened into martensite. Etching method and etchant selection, refer to C.3.1.5 in GB/T 6394.
Ferrite mesh method. After austenitizing the sample under the conditions specified in 4.1, the sample is cooled in a cooling manner capable of obtaining reticulated ferrite.
The "reticulated ferrite pearlite" or "reticulated ferrite martensite, bainite" structure is obtained. After grinding, polishing and etching, the original the reticulated ferrite precipitated at the austenite grain boundaries shows the original austenite grains. Sample cooling method, etching method and etchant selection, refer to C.3.1.2 of GB/T 6394.
4.2.2 The method and selection of austenite grain size of non-quenched and tempered steel shall be in accordance with GB/T 6394.
5 Inspection method of actual grain size of non-quenched and tempered steel products
5.1 Non-quenched and tempered steel products that need to be tested for actual grain size may include non-quenched and tempered steel hot-rolled steel bars, steel tubes, and Non-quenched and tempered steel forgings.
5.2 The actual grain size sample shall be taken from the sample or sample under delivery.
For cold-drawn or hot-rolled non-quenched and tempered steel hot-rolled steel bars and steel pipes, the sampling location refers to the tensile or impact specified in GB/T 2975.
The sample sampling position is required to be performed, and the preparation of the sample is performed according to GB/T 13298.
For non-quenched and tempered steel forgings, the sampling position should meet the metallurgical technical requirements of related products Evaluate the actual grain size); for eutectoid steel or "pearlite-ferrite" non-quenched and tempered steel forgings with low ferrite content, Selection should also consider the display of grain size.
14176-Test method for average grain size of non-quenched and tempered steel and its products.indd 2.2017/11/7 9.58.30 14176-Test method for average grain size of non-quenched and tempered steel and its products.indd 3.2017/11/7 9.58.31 14176-Test method for average grain size of non-quenched and tempered steel and its products.indd 4.2017/11/7 9.58.31 14176-Test method for average grain size of non-quenched and tempered steel and its products.indd 5.2017/11/7 9.58.32 14176-Test method for average grain size of non-quenched and tempered steel and its products.indd 6.2017/11/7 9.58.32 T/CSAE 58-2017 Test method for estimating average grain size of microalloying non-quenched and tempered steel and its products Test method for estimating average grain size of microalloying non-quenched and tempered steel and its products Chinese Society of Automotive Engineers Test method for average grain size of non-quenched and tempered steel and its products Published by the Chinese Society of Automotive Engineers 2017-11-03 Release 2017-11-03 Implementation 14176-Test method for average grain size of non-quenched and tempered steel and its products.indd 1.2017/11/7 9.58.30 Published by the Chinese Society of Automotive Engineers this standard aims to improve the level of product research and development, manufacturing and so on.
Adoption of the standard is entirely voluntary, its availability and applicability for any particular purpose, including possible the other risks of the user shall be borne by the adopter.
13936-General technical standards for rolled differential plates for automobiles.indd 2.2017/11/7 10.36.26 Contents Foreword ... III
1 Scope ... 1
2 Normative references ... 1
3 Terms and definitions ... 1
4 Test method for austenite grain size of non-quenched and tempered steel ... 2
4.1 Formation conditions of austenite grain size of non-quenched and tempered steel ... 2
4.2 Display and determination of essential grain size of non-quenched and tempered steel ... 2
5 Inspection method of actual grain size of non-quenched and tempered steel products ... 2
6 Grain Size Report ... 6 Fig. 1 38MnS6 Crankshaft connecting rod neck fillet matrix structure ... 3
Figure 2 38MnSiVS6 connecting rod base body structure ... 3
Figure 3 F45VS crankshaft connecting rod neck base tissue ... 4
Figure 4 30MnVS wheel base matrix ... 4
Figure 5 Decarburization layer structure of 70S connecting rod ... 5
Figure 6 Decarburization layer structure of 70S connecting rod (polished surface is parallel to the surface of forged and rolled surface) ... 5
Figure 7 45VS crankshaft connecting rod neck fillet matrix ... 6
14176-Test method for average grain size of non-quenched and tempered steel and its products.indd 1.2017/11/7 9.58.30 14176-Test method for average grain size of non-quenched and tempered steel and its products.indd 2.2017/11/7 9.58.30
Foreword
In order to facilitate the evaluation of the austenite grain size growth tendency of non-quenched and tempered structural steel under forging heating or controlled cooling after forging, and non-quenching and tempering the actual grain size of steel rolling, forging, and forgings is specially formulated for this standard.
Compared with quenched and tempered steel parts, the austenite formation temperature of non-tempered steel forgings is higher, and the same austenite crystal as quenched and tempered steel is used.
The particle size formation temperature is inconsistent with the actual process state. Non-quenched and tempered steel rolled, forged or forged structures may be "flaky pearlite" "Ferrite", flake pearlite, low carbon martensite, granular bainite, etc. For the first two microstructure states, the evaluation of the actual grain size the method is not specifically stipulated in GB/T 6394-2002 "Method for determination of metal average grain size".
This standard complies with GB/T 6394-2002 "Method for Determining the Average Grain Size of Metals".
The production process and organizational characteristics are adapted.
Appendix A of this standard is a normative appendix.
This standard was proposed by the Material Branch of the Chinese Society of Automotive Engineers.
This standard was approved by the Chinese Society of Automotive Engineers.
This standard was first issued in November.2017.
This standard was drafted. Dongfeng Motor Corporation, China FAW Group Corporation, Jiangling Automobile Co., Ltd., Northeast Special Iron and Steel Co., Ltd., Jiangyin Xingcheng Special Steel Co., Ltd., Hubei Xinye Steel Co., Ltd., and Shougang Group Co., Ltd.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 8 pages — is available in the English PDF.
How to Download T/CSAE 58-2017
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
T/CSAE 124.1-2020 — Automotive variable-displacement pendulum oil pump - Terminology
T/CSAE 124.2-2020 — Automotive variable-displacement pendulum oil pump - technical specification Drafting
T/CSAE 124.3-2020 — Automotive variable-displacement pendulum oil pump - Test method and device
T/CSAE 58-2017
$205.00