Valid

T/CSAE 50-2016Dent Resistance Test Standard of Automobile Outer Panel (English PDF)

汽车外覆盖件抗凹性能测试标准

Preview PDF

This is a limited preview

Buy now to download the full PDF (11 pages)

Need quotation for your management?

Get a formal quotation for T/CSAE 50-2016 in 30 minutes.

Issued by

China Society of Automotive Engineers

Level / Type

National · Mandatory

Issue date

May 26, 2016

Implementation date

May 26, 2016

Scope

T/CSAE 50-2016 is the English-translated version of 汽车外覆盖件抗凹性能测试标准.

T/CSAE 50-2016 — This specification specifies the relevant definitions, principles, test equipment, test procedures, and tests for the test methods for the anti-concave performance of automotive exterior covers.

Data processing method. This specification applies to passenger cars and light commercial vehicles, including body-in-white and related paint parts.

Found what you need?

Document preview — T/CSAE 50-2016

National Standard of the People's Republic of China

ICS
43.120
Classification
T 40

Issued by: China Society of Automotive Engineers

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 3.1 Automotive exterior cover
  • 3.2 Anti-concave performance
  • 3.3 Anti-concave stiffness
  • 3.4 Anti-concave stability
  • 3.5 Dent
  • 3.6 Depression
  • 3.7 Instability depression
  • 3.8 Unstable depression load
  • 3.9 Hard instability depression
  • 3.10 Soft instability depression
  • 3.11 Quasi-static loading
  • 3.12 Surface Accessories
  • 3.13 Preloading
  • 3.14 Post loading
  • 3.15 Initial stiffness
  • 3.16 Secondary stiffness
  • 3.17 Final stiffness
  • 4 Test samples
  • 4.1 Sample requirements
  • 4.2 Test area
  • 5 Test device
  • 5.1 Bench composition
  • 5.2 Benchmark Platform
  • 5.3 Frame column
  • 5.4 Loading mechanism
  • 5.5 Indenter
  • 5.6 Motion Control
  • 5.7 Sensor and data acquisition
  • 6 Test preparation
  • 6.1 Environmental conditions
  • 6.2 Sample inspection
  • 6.3 Measurement point preparation
  • 7 Test steps
  • 7.1 Sample arrangement and constraint method
  • 7.2 Quasi-static anti-concave test process
  • 8 Test data processing
  • 8.1 Single load method data processing
  • 8.2 Incremental loading method data processing
  • 9 Test report

Foreword

In order to meet the needs of China's automotive product design and development, the domestic automotive industry automotive outer cover anti-concave performance test method is regulated.

This specification is specifically formulated.

1 Scope

This specification specifies the relevant definitions, principles, test equipment, test procedures, and tests for the test methods for the anti-concave performance of automotive exterior covers.

Data processing method.

This specification applies to passenger cars and light commercial vehicles, including body-in-white and related paint parts.

2 Normative references

The following documents are indispensable for the application of this specification. For dated references, only the date of the date indicated Applicable to this document. For undated references, the latest edition applies to this document.

SAE J2575-2004 Standardized Dent Resistance Test Procedure

3 Terms and definitions

The following terms and definitions apply to this specification.

3.1 Automotive exterior cover

A car cover is a space-shaped surface or inner surface made of a metal sheet covering an engine, a chassis, and a cab or a body.

Parts. According to the function and location, it can be divided into three types. outer cover, inner cover and skeleton cover. The outer cover mainly includes the outer panel of the door, Front fender, side outer panel, hood outer panel, top cover outer panel, trunk (or tailgate) inner and outer panels, etc.

3.2 Anti-concave performance

Anti-concave performance refers to the ability of the outer cover of the car to resist concave deflection and local deformation and maintain shape under the action of external load.

The force mainly includes three aspects, namely, anti-concave stiffness, anti-concave stability and residual deformation.

3.3 Anti-concave stiffness

The anti-concave stiffness refers to the ability of the cover to resist the deflection of the depression. The following methods can be used to test and evaluate. 1. A certain external load the magnitude of the deflection displacement of the depression generated below; 2. The magnitude of the external load when a certain deflection is generated; 3. When the external load acts the slope value of the Displacement-Load curve.

3.4 Anti-concave stability

When the external load reaches a certain level and the load is constant or slightly changed, the ability of the outer cover of the automobile to resist elastic deformation is suddenly lost.

The occurrence of instability, that is, the oil can effect, is manifested as the phenomenon of "big pass" and "quick turn", and the ability of the outer cover of the car to resist instability.

It is called anti-concave stability.

3.5 Dent

After unloading, permanent plastic deformation occurs at the loading point of the specimen.

T/CSAE XX-XXXX

3.6 Depression

The depression refers to the non-permanent deformation (elastic deformation of the material) that occurs locally on the outer cover of the body when subjected to force, resulting in the curvature of the cover.

The original design is reversed.

3.7 Instability depression

Oil-canning refers to the local reversal of the curvature of the sample collected during the loading process of the outer cover of the automobile.

Often accompanied by sound.

3.8 Unstable depression load

The unstable sag load is the minimum load that occurs the oil can effect, that is, the load-displacement curve is from the linear part to the nonlinear part.

The amount of load when the offset is displayed.

3.9 Hard instability depression

When the hard instability depression refers to the occurrence of the unstable depression, the surface curvature of the outer cover of the automobile is reversed faster than the movement speed of the pressure head, and the load-displacement the curve appears as a drop in load, but the displacement continues to increase. As shown in Figure 1.

3.10 Soft instability depression

Soft instability depression refers to the occurrence of unstable depression, the surface curvature of the outer cover of the car is reversed faster than the speed of the indenter, surface and pressure the head remains in contact and the load-displacement curve appears as a slope decrease, but is always positive. As shown in Figure 1.

Figure 1 Oil can effect type

3.11 Quasi-static loading

Quasi-static loading is a process of generating depressions at low speeds. The loading speed is generally required to be no more than 127 mm/min. Recommended the loading speed is 50 mm/min.

TC SAE XX-XXXX

3.12 Surface Accessories

Surface attachments include hinges, locks, bumpers, and other parts used for the attachment of sheet metal parts such as car roofs and door covers.

3.13 Preloading

Preloading applies a certain load to the measured point of the sample to be tested before the incremental loading method.

3.14 Post loading

Post-loading is the load applied to determine the dent produced by the last cycle load after the incremental method is loaded.

3.15 Initial stiffness

The initial stiffness is the slope value of the initial linear portion of the load-displacement curve, usually a positive value. as shown in picture 2.

3.16 Secondary stiffness

The secondary stiffness is the slope value of the second linear portion of the load-displacement curve, which occurs after the oil can effect. Clear with initial stiffness Unlike, it is located in the area after the curve inflection point. as shown in picture 2.

3.17 Final stiffness

The final stiffness is the slope value at the end of the load-displacement curve (before the maximum load arrives).

Figure 2 Initial stiffness, secondary stiffness and final stiffness

T/CSAE XX-XXXX

4 Test samples

4.1 Sample requirements

The test piece to be tested in this test shall be a post-curing body assembly and include all accessories that affect the surface stiffness of the outer panel. Specific requirements are as follows.

4.1.1 The door assembly shall include a lock body, an internal bracket, a reinforcing pad, an outer handle, and a soundproof material.

4.1.2 The engine cover and trunk lid (or tailgate) assembly shall include a lock body (or lock), an internal bracket, a reinforcing mat, and an outer handle.

Sound insulation materials, exterior parts, etc.

4.1.3 The roof of the car body shall include the sunroof assembly (if equipped), exterior parts and so on.

4.1.4 Side panels, fenders and other exterior surfaces of the body shall contain corresponding exterior trim and reinforcement.

4.2 Test area

The test area is the area where the test piece can be tested for anti-concavity performance.

The test area resisting the concave stiffness is mainly near the geometric center of the outer plate and the center of the largest unsupported area.

When measuring dents, select the area that is most likely to be pressed by external force when the door is closed, usually the side door, engine cover, trunk Covers (or tailgates), side panels, and fenders are within 300 mm of the edge of the outer cover, as shown in Figure 3.

Figure 3 Dent measurement test area

5 Test device

5.1 Bench composition

The test equipment rig mainly includes a reference platform, a frame column, a loading mechanism, a motion control system, a sensor, data acquisition, and Processing system, etc.

TC SAE XX-XXXX

Figure 4 Bench test system

5.2 Benchmark Platform

The reference platform is used to place the sample to be tested, usually using standard iron floor, and its size should meet the requirements of the tested sample and fixture.

Arrangement.

5.3 Frame column

The test rig frame column is perpendicular to the top of the reference platform and is mainly used for loading and moving of the loading mechanism, and its own and the reference platform.

Rigid connection.

5.4 Loading mechanism

The loading mechanism used in the anti-concave performance test shall meet the following requirements (recommended to use servo electric cylinders).

5.4.1 The loading mechanism itself should be sufficiently rigid along the loading direction (should be satisfied under both static and quasi-static conditions).

5.4.2 The loading direction of the loading mechanism should be able to rotate at least in the X and Y directions.

5.4.3 The total movement of the loading mechanism is not less than.200 mm.

5.4.4 The maximum load that the loading mechanism can withstand is not less than 2000 N.

5.4.5 The displacement of the moving part of the loading mechanism should be precisely controlled, and the minimum motion unit is not more than 5 µm.

5.4.6 The loading mechanism should be easy to install displacement and force sensors, and should ensure that the quasi-static loading/unloading process is small.

Mechanical vibration.

5.5 Indenter

Automotive outer cover anti-concave performance test The indenter used in the loading process is usually divided into a hard indenter and a soft indenter. This test uses the standard Static loading method, the test head is a steel hard head. The specific requirements are as follows.

Surface shape. hemispherical structure, as shown in Figure 5.

Size. Spherical diameter Phi 25.4 mm.

T/CSAE XX-XXXX

Material hardness. not less than Rc 55.

Surface roughness. no more than 0.254 µm.

Figure 5 test head

5.6 Motion Control

The motion control mode of the test device should be closed-loop control of load and displacement.

The test target stroke, loading range, plus/unloading mode, etc. should be pre-defined, and the speed and displacement should be accurately controlled during the movement.

The displacement program control accuracy is not less than 10 µm.

The motion control program has protection measures against overload and overshoot.

5.7 Sensor and data acquisition

Anti-concave performance test sensor requirements.

Force sensor. The range is not less than 500 N, and the accuracy is not less than 1N.

Displacement sensor. The range is not less than.200 mm and the accuracy is not less than 10 µm.

The test data acquisition uses special collection equipment and application software. The load and displacement data acquisition frequency is not less than 50 Hz, and the software should be able to Record and save the load-displacement curve.

6 Test preparation

6.1 Environmental conditions

Unless otherwise stated by the standard or required by the purchaser, the environmental conditions of this test are normal temperature and standard atmospheric pressure.

6.2 Sample inspection

Before the test, the test engineer and the demander shall confirm the completeness of the sample assembly as described in 4.1, and check the surface of the sample.

Cracks, lacquer flaking or concave (scratch) marks to ensure that the sample meets the test requirements.

6.3 Measurement point preparation

6.3.1 The measuring points shall be selected within the test area specified in 4.2, and each test (measurement of anti-concave stiffness and dent) shall be measured.

At least 3 points.

TC SAE XX-XXXX

6.3.2 Principle of selection. the geometric center of the outer surface of the outer cover of the car or the center of the largest unsupported area. As shown in Figure 6, the side door, hair Typical outer covers such as the engine cover, trunk lid, tailgate, and fender are recommended for measuring point locations.

6.3.3 Unless otherwise stated or required by the purchaser, the selected measuring point should avoid surface feature locations (such as hemmings, holes) and reinforcement pads, Ribs and other locations that affect the surface's resistance to concave.

6.3.4 Mark the selected measuring point on the sample and record the corresponding size position.

(a) Side door measurement points and restraint methods (b) hood measurement points and restraint methods T/CSAE XX-XXXX (c) Luggage cover measurement points and restraint methods (d) tail (lift) door measurement point and constraint method (e) Fender measuring points and restraint methods

Figure 6 Example of selection of different parts measuring points and constraints

TC SAE XX-XXXX

7 Test steps

7.1 Sample arrangement and constraint method

7.1.1 When the outer surface of the body is tested, the body in white should be rigidly fixed to the reference platform, as shown in Figure 7.

Figure 7 How the body-in-white is fixed on the reference platform

7.1.2 When the outer surface of the door cover part is tested separately, the parts can be placed on the special fixture (or table top), but it must be guaranteed the rigid connection of the reference platform is shown in Figure 8.

Figure 8 How the door cover parts are fixed on the reference platform

7.1.3 The method of restraining the sample should be as close as possible to the constraints of the original car. For the door cover parts, refer to the method recommended in Figure 5. for Parts that are thinner (such as fenders, side panels, etc.), less rigid, and difficult to individually restrain, can be directly assembled on the body-in-white to test Inspect, the body-in-white is fixed with reference to 7.1.1.

7.2 Quasi-static anti-concave test process

7.2.1 Test loading method selection

There are usually two types of quasi-static anti-concave test loading methods. single loading method and incremental loading method.

T/CSAE XX-XXXX

The single loading method is used to measure the initial stiffness and the unstable sag load.

The incremental loading method is used to measure residual deformation, ie dents.

7.2.2 Single load method

7.2.2.1 Calibrate the force and displacement sensors before loading.

7.2.2.2 Manual console rack loading mechanism, move it above the sample measuring point and rotate the indenter to the measuring point surface normal Towards, then control the indenter to a position approximately 1 mm from the surface of the measuring point.

7.2.2.3 Set the loading speed (no more than 50 mm/min).

7.2.2.4 Set the maximum target load (refer to the part design requirements, generally at least 150 N).

7.2.2.5 Start a single load program, automatic operation, observation force, displacement sensor data and its real-time synchronization curve.

7.2.2.6 After the load-unload process is completed, save the test data.

7.2.3 Incremental loading method

7.2.3.1 Calibrate the force and displacement sensors before loading.

7.2.3.2 Manual console rack loading mechanism, move it above the sample measuring point and rotate the indenter to the measuring point surface normal Towards, then control the indenter to a position approximately 1 mm from the surface of the measuring point.

7.2.3.3 Set the loading speed (no more than 50 mm/min).

7.2.3.4 Set the preload value 7 N.

7.2.3.5 Start the program and complete the preload-uninstall process.

7.2.3.6 Set the target load value for each stage of incremental loading (50N, 0 N, 70 N, 0 N, 90 N, 0 N, 110 N, 0 N,

130 N, 0 N, 150 N, 0 N, 170 N, 0 N, 190 N, 0 N, 210 N, 0 N).

Note--The above loop increments are for reference only. Users can select high or low cyclic loading cycles according to different requirements. Follow the load increment of the ring incremental loading is generally selected in the range of 10-50N.

7.2.3.7 Load the value 7 N after setting.

7.2.3.8 Start the program and complete the load-unload process.

7.2.3.9 During the operation of the program, the observation force, displacement sensor data and its real-time synchronization curve.

7.2.3.10 Incremental Method Loading - After the uninstall process is completed, the test data is saved.

8 Test data processing

8.1 Single load method data processing

8.1.1 Initial stiffness Select the initial linear segment data in the load-displacement curve of the loading process to process, that is, to determine the slope of the segment.

Generally obtained by linear least squares method.

TC SAE XX-XXXX

8.1.2 The instability sag load is obtained by solving the first derivative of the displacement versus displacement. if the derivative minimum is negative, the instability sag load is the load value when the derivative is 0 for the first time (hard instability sag load); if the derivative minimum is positive, the unstable sag load is the minimum derivative the value corresponds to the load (soft instability sag load).

8.2 Incremental loading method data processing

8.2.1 Reference displacement. Interpolation calculates the displacement value at 5 N by preloading the phase data.

8.2.2 Depression displacement. Take the displacement value when the load is 5 N in each incremental loading phase.

8.2.3 The difference between the concave displacement and the reference displacement for each incremental loading cycle is the residual deformation (dent) of the incremental loading cycle. 210 N the residual deformation (dent) of the load cycle is the difference between the concave displacement and the reference displacement of the post-load period.

9 Test report

The content of this test report should include but is not limited to the following.

9.1 Test purpose, principle, and object to be tested;

9.2 Test conditions and methods;

9.3 Test data records. test photos, process data curves and original values;

9.4 Test data processing. loading curve, data processing method;

9.5 Test results. should include at least initial stiffness, unstable depressions (and types), dents, etc.;

9.6 Test conclusions.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 11 pages — is available in the English PDF.

How to Download T/CSAE 50-2016

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
11 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

T/CSAE 50-2016

$210.00