Valid

T/CSAE 152-2020Technical requirements of automotive audio video bridging (AVB) (English PDF)

车载音视频桥(AVB)技术要求

Preview PDF

This is a limited preview

Buy now to download the full PDF (9 pages)

Need quotation for your management?

Get a formal quotation for T/CSAE 152-2020 in 30 minutes.

Issued by

China Society of Automotive Engineers

Level / Type

National · Mandatory

Issue date

August 7, 2020

Implementation date

January 1, 1970

Scope

T/CSAE 152-2020 is the English-translated version of 车载音视频桥(AVB)技术要求.

T/CSAE 152-2020 — This standard specifies the system functional requirements and node requirements of the on-board audio and video bridge.

This standard is applicable to the development of vehicle audio and video bridge enterprise standards of car manufacturers, and the vehicle audio and video bridge systems and nodes of system manufacturers and equipment manufacturers. Development guidance.

Found what you need?

Document preview — T/CSAE 152-2020

National Standard of the People's Republic of China

ICS
33.160.01
Classification
T 40

Issued by: China Society of Automotive Engineers

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Abbreviations
  • 5 Vehicle AVB network architecture
  • 6 Functional requirements
  • 6.1 Ethernet transmission
  • 6.2 Time synchronization
  • 6.3 Transmission scheduling
  • 6.4 Flow Filtration and Control
  • 6.5 Business Packaging
  • 6.6 Data encryption and integrity protection
  • 6.7 Frame copy and erase
  • 7 Node requirements
  • 7.1 Bridge Node
  • 7.2 Source node
  • 7.3 Target node
  • References

1 Scope

This standard specifies the system functional requirements and node requirements of the on-board audio and video bridge.

This standard is applicable to the development of vehicle audio and video bridge enterprise standards of car manufacturers, and the vehicle audio and video bridge systems and nodes of system manufacturers and equipment manufacturers.

Development guidance.

2 Normative references

The following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this article Pieces. For undated reference documents, the latest version (including all amendments) is applicable to this document.

IEEE Std 802.1AS Local and metropolitan area network bridging the timing and synchronization of time-sensitive applications in the local area network (Local and metropolitan area networks-Timing and Synchronization for Time-Sensitive Applications in Bridged Local Area Networks) IEEE Std 802.1BA local and metropolitan area networks audio and video bridging system (Local and metropolitan area networks-Audio Video Bridging (AVB) Systems) IEEE Std 802.1Qat Local and Metropolitan Area Network Virtual Bridge LAN Patch 14.Stream Reservation (Local and Metropolitan area networks-Virtual Bridged Local Area Networks-Amendment 14.Stream Reservation Protocol(SRP)) IEEE Std 802.1Qav Local and Metropolitan Area Network Virtual Bridge Local Area Network Patch 12.Time-sensitive service flow forwarding and queuing enhancement (Local and metropolitan area networks-Virtual Bridged Local Area Networks-Amendment 12.

Forwarding and Queuing Enhancements for Time-Sensitive Streams) IEEE Std 1722 A Transport Protocol for Time-Sensitive Application Transmission Protocol for Bridged LANs Applications in Bridged Local Area Networks)

3 Terms and definitions

The following terms and definitions apply to this standard.

Automotive audio video bridging (AVB) system the vehicle audio and video bridge network and the carried vehicle audio and video streams together constitute the vehicle audio and video bridge system.

Automotive AVB network the bridge nodes, end nodes and other nodes that meet the requirements of this standard are a continuous collection of in-vehicle Ethernet connections.

Automotive AVB stream in the vehicle-mounted AVB network, audio and video streams with transmission bandwidth are reserved.

Stream reservation protocol (SRP) domain in a vehicle-mounted AVB network, a logical collection of consecutive nodes with the same stream reservation class (SR Class) and AVB stream transmission priority.

Generalized precision time protocol (gPTP) domain in the vehicle-mounted AVB network, a logical collection of continuous nodes that meet the time synchronization requirements of this standard.

Automotive AVB domain the intersection of the SRP domain and the gPTP domain.

Bridging node

In the vehicle AVB network, the bridge device that transfers the AVB stream.

Source node

In the vehicle-mounted AVB network, the source terminal device of the AVB stream.

Target node

In the vehicle-mounted AVB network, the target terminal device of the AVB stream.

3.10

End node

The collective term for Source Node and Target Node.

4 Abbreviations

The following abbreviations apply to this standard.

node

Not within the scope of this standard.

6 Functional requirements

6.1 Ethernet transmission

The relevant requirements are as follows.

--Transmission rate. Support at least 100 Mbps in-vehicle Ethernet, such as IEEE Std 802.3bw, IEEE Std 802.3bp.

--Auto-negotiation AN. The 1000BASE-T1 PHY of the in-vehicle Ethernet carrying the AVB stream should not be turned on.

--Efficient Ethernet EEE. EEE should not be enabled on the vehicle-mounted Ethernet port that carries AVB streams.

--Package length restriction. Ethernet packet payload should not exceed 1500 bytes.

6.2 Time synchronization

6.2.1 Synchronization accuracy

This standard uses the time synchronization mechanism defined by IEEE Std802.1AS to meet the needs of on-board AVB stream counterparts, multi-screen synchronized playback, etc.

For time synchronization basis. All nodes in the vehicle AVB network should support IEEE Std 802.1AS. In the vehicle AVB network with no more than 7 hops, the time error between any two nodes does not exceed 1 µs.

6.2.2 Time synchronization types of nodes and ports

In the vehicle AVB network, the best master clock algorithm BMCA should not be used to determine the time synchronization master node GM, and the pre-configuration method should be used Determine the role of the node in the gPTP domain and the clock type of the port carrying the AVB stream to shorten the startup time of the vehicle AVB system.

At one moment, there should be and only one node in the gPTP domain of the vehicle AVB network as a GM, and the remaining nodes are all timing slave nodes.

As shown in Figure 3, node 1 is GM, and the remaining nodes are slaves. GM docking bridge node

6.2.3 Adjacent node conduction delay

The neighborPropDelay is used to calculate the current time. In a vehicle-mounted closed environment, the conduction delay of adjacent nodes is relatively for fixed, the timing slave node Slave should pre-configure the adjacent node conduction delay in the non-destructible storage. At startup, use the pre-configured neighbor the node conduction delay corrects the local clock of the Slave. After startup, through the standard method defined by IEEE Std 802.1AS, calculate and obtain neighbors the current stable value of the node conduction delay. The current stable value can be used to refresh the transmission delay of the pre-configured neighboring node and obtain a new pre-configured neighboring node Transmission delay. The difference between the current stable value and the transmission delay of the pre-configured neighbor node exceeds 100 ns, and the current stable value is used as the new pre-configured neighbor node.

Node transmission delay. A variety of filtering methods can be used to obtain the current stable value, which is not restricted by this standard.

In IEEE Std 802.1AS, when the transmission delay of the neighboring node exceeds the neighborPropDelayThresh, Will cause port synchronization to fail. This standard does not allow this to happen.

Slave can pre-configure the rate ratio rateRatio and the neighbor rate ratio neighborRateRatio to accelerate time synchronization.

6.2.4 Time synchronization information sending interval

In different stages of time synchronization, the sending interval of time synchronization messages can be flexibly adjusted to balance different needs. Initial synchronization phase, configuration Shorter sending interval speeds up synchronization convergence and supports quick start. In the synchronization maintenance phase, configure a longer sending interval to reduce the equipment load, Reduce bandwidth usage. All nodes in the gPTP domain shall support the time synchronization information sending interval configuration shown in Table 1.

Table 1 Recommended time synchronization information sending interval configuration

The adjustment of the time synchronization information sending interval is triggered by Slave. Slave should send the adjustment information within 60 s after the time synchronization is completed.

The entire information carries the desired Sync/PdelayReq message sending interval. The bridge node can be based on the interval on the master port of all active clocks Adjust the information to trigger the adjustment of the message sending interval on the Slave port. The time synchronization message sending interval of the Slave port should be the same as that of all Masters.

The minimum interval for sending time synchronization messages on the port is the same.

6.3 Transmission scheduling

6.3.1 Bandwidth reservation

The vehicle AVB system should support the reservation of transmission bandwidth through pre-configuration. On any port that activates the AVB stream, all AVB streams the accumulated reserved bandwidth should not exceed 75% of the port bandwidth.

6.3.2 Credit-based scheduling mechanism

The vehicular AVB system should support the absolute priority scheduling mechanism and the credit-based scheduling mechanism CBS. The AVB stream priority should be higher than the non-AVB stream.

Absolute priority scheduling mechanism, refer to IEEE Std 802.1Q.

CBS, a credit-based scheduling mechanism, smooths the transmission of AVB streams in the entire system on the basis of providing transmission bandwidth that meets the requirements of AVB streams.

It can reduce network congestion and ensure that the upper bound of transmission delay is within the required range of AVB stream. The maximum transmission delay of AVB stream is not more than 7 hops in the vehicle-mounted AVB network, the end-to-end delay of the AVB stream from the source node layer 2 to the target node layer 2.CBS parameter definition and technical details, refer to IEEE Std 802.1Qat.

For AVB streams, this standard defines 4 types of SR Class templates, as shown in Table 2.

Table 2 SR Class template

In practical applications, at most two SR Classes should be selected to transmit AVB streams, corresponding to SR Class A and SR Class B respectively. among them SR Class A corresponds to the SR Class template with higher maximum transmission delay requirements. Priority 3 is used in transmission, and SR Class B corresponds to the maximum SR Class template with lower transmission delay requirement, priority 2 is used in transmission. When only one type of SR Class is used, the default is SR Class B. It is not advisable to enable the MAC control PAUSE and Priority-based flow defined by IEEEStd 802.3 on the port that activates the AVB flow.

control function.

6.4 Flow Filtration and Control

Multiple AVB streams using the same SR Class share the transmission bandwidth reserved by the SR Class. When an abnormal burst occurs in a certain AVB stream, it will squeeze the transmission bandwidth of other normal AVB streams. Enable the PSFP feature defined by IEEE Std 802.1Qci to filter abnormal flows.

Avoid the impact on other normal flows.

6.5 Business Packaging

In this standard, the AVB stream is encapsulated using IEEE Std1722.

The 1722 service encapsulation format that the source node and target node should support.

a) AAF (AVTP Audio Format) 16bit/24bit PCM quantization, 48Khz/44.1Khz sampling rate, normal/sparse time stamp mode. When the target node supports when the number of channels is lower than the source node, the target node will only play the audio samples corresponding to the number of channels. When the number of channels of the source node's audio source changes During conversion, the source node indicates the channel change through the Event field of the AAF frame header. For more details, refer to IEEE Std 1722;

b) CVF (Compressed Video Format) H.264, MJPEG (Motion JPEG);

c) IEC 61883/IIDC Format MPEG2-TS.

Presentation Time Offset and Maximum Timing in the 1722 frame header the correspondence between Uncertainty and SR Class is shown in Table 3.

Table 3 Correspondence between Presentation Time, Maximum Timing Uncertainty and SR Class

6.6 Data encryption and integrity protection

This standard does not involve data encryption and integrity protection constraints for AVB streams.

6.7 Frame copy and erasure

When there are multiple transmission paths between the source node and the target node, through frame replication and elimination technology, use different transmission paths to avoid Packet loss or service interruption caused by interference or failure of a certain path can improve the transmission reliability of AVB streams. The source node performs frame copy, bridge section Point and target nodes perform duplicate frame elimination, refer to IEEE Std 802.1CB-2017.

7 Node requirements

7.1 Bridge node

At least two ports of the bridge node should meet the following requirements.

Mandatory requirements.

a) Support 100 Mbps/1 Gbps automotive Ethernet;

b) Support gPTP time synchronization;

c) Support port clock role configuration and neighbor node transmission delay configuration;

d) Support Sync/PdelayReq transmission cycle adjustment;

e) Support static bandwidth reservation, and the cumulative bandwidth of all AVB streams accounts for no more than 75% of the port bandwidth;

f) Support at least 2 types of priority, at least one of which is used for AVB streams;

g) Support CBS scheduling, at least support SR Class B;

Optional requirements.

a) Support flow filtering and management;

b) Support frame copy and erasure.

7.2 Source node

At least one port of the source node should meet the following requirements.

Mandatory requirements.

a) Support 100 Mbps/1 Gbps automotive Ethernet;

b) Support gPTP time synchronization;

c) Support port clock role configuration and neighbor node transmission delay configuration;

d) Support Sync/PdelayReq transmission cycle adjustment;

e) Support at least 1 AVB stream transmission;

f) Support static bandwidth reservation, and the cumulative bandwidth of all AVB streams accounts for no more than 75% of the port bandwidth;

g) Support filling in Presentation Time Offset and Maximum Timing Uncertainty in 6.5;

h) Support at least one 1722 encapsulation format in 6.5, used to encapsulate the AVB stream in e);

i) Support CBS scheduling, at least support SR Class B;

Optional requirements.

Support frame duplication and elimination.

7.3 Target node

At least one port of the target node should meet the following requirements.

Mandatory requirements.

a) Support 100 Mbps/1 Gbps automotive Ethernet;

b) Support gPTP time synchronization;

c) Support port clock role configuration and neighbor node transmission delay configuration;

d) Support Sync/PdelayReq transmission cycle adjustment;

e) Support at least 1 audio and video stream reception;

f) Support the reading of Presentation Time Offset and Maximum Timing Uncertainty in 6.5;

g) Support all 1722 business packages in 6.5;

Optional requirements.

Support frame duplication and elimination.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 9 pages — is available in the English PDF.

How to Download T/CSAE 152-2020

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
9 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

T/CSAE 152-2020

$185.00