Valid

SY/T 7454-2019Technical specification for CO2 flooding reservoir engineering plan in sandstone oilfield (English PDF)

砂岩油田二氧化碳驱油藏工程方案编制技术规范

Preview PDF

This is a limited preview

Buy now to download the full PDF (13 pages)

Need quotation for your management?

Get a formal quotation for SY/T 7454-2019 in 30 minutes.

Issued by

National Energy Administration

Level / Type

National · Recommended

Issue date

January 1, 2019

Implementation date

May 1, 2020

Scope

SY/T 7454-2019 is the English-translated version of 砂岩油田二氧化碳驱油藏工程方案编制技术规范.

SY/T 7454-2019 is the Chinese standard "Technical specification for CO2 flooding reservoir engineering plan in sandstone oilfield". It was issued by National Energy Administration.

Found what you need?

Document preview — SY/T 7454-2019

National Standard of the People's Republic of China

ICS
75.020
Classification
E12

Issued by: National Energy Administration

Contents

  • [Preview only]
  • 1 Scope
  • 1.2 Definition of terms
  • 2 Normative references
  • 2.1 General requirements
  • 2.2 Pressure-drop limitations and piping configurations
  • 2.3 Inlet stresses that originate from static loads in the discharge piping
  • 2.4 Inlet stresses that originate from discharge reaction forces
  • 2.5 Isolation valves in inlet piping
  • 2.6 Rupture disk devices in combination with pressure relief valves
  • 2.7 Process laterals connected to inlet piping of pressure relief valves
  • 2.8 Turbulence in pressure relief device inlets
  • 3 Terms and definitions
  • 3.2 Safe disposal of relieving fluids
  • 3.3 Back pressure limitations and sizing of pipe
  • 3.4 Considerations for pilot-operated pressure relief valves
  • 3.5 Stresses that originate from discharge piping
  • 3.6 Isolation valves in the discharge piping
  • 4 Isolation valves in pressure relief piping
  • 4.1 Determination of relief requirements
  • 4.2 Relieving pressure
  • 4.3 Sizing for gas or vapor relief
  • 4.4 Examples of isolation valve installations
  • 4.5 Sizing for liquid relief: relief valves requiring liquid capacity certification
  • 4.6 Sizing for liquid relief: relief valves not requiring liquid capacity certification
  • 4.7 Sizing for two-phase liquid/vapor relief
  • 4.8 Sizing for rupture disk devices
  • 5 Bonnet or pilot vent piping
  • 5.1 Conventional pressure relief valves
  • 5.2 Balanced bellows pressure relief valves
  • 5.3 Balanced piston pressure relief valve
  • 5.4 Pilot-operated pressure relief valves
  • 5.5 Thickness calculation of planar insulation layer
  • 6 Drain piping
  • 6.1 Installation conditions that require drain piping
  • 6.2 Safe practice for installation of drain piping
  • 6.3 SPM Location and Spatial Requirements
  • 6.4 Other materials
  • 6.5 Transportation, storage and custody of materials
  • 7 Pressure relief device location and position
  • 7.1 Inspection and maintenance
  • 7.2 Proximity to pressure source
  • 7.3 Proximity to other equipment
  • 7.4 Mounting position
  • 7.5 Test or lifting levers
  • 7.6 Heat tracing and insulation
  • 8 Bolting and gasketing
  • 8.1 Care in installation
  • 8.2 Proper gasketing and bolting for service requirements
  • 8.3 Welding
  • 8.4 Quality Control and Inspection
  • 9 Multiple pressure relief valves with staggered settings
  • 9.2 Installation of Mooring Foundation
  • 9.3 Laying of Mooring Lines
  • 9.4 Hook-up of Mooring Lines

1 Foreword

SY/T 7454-2019 was issued by National Energy Administration on 4 November 2019 and has been in force since 1 May 2020.

The SY/T prefix marks a recommended standard. It is not law in itself: it becomes binding when a contract names it, when a regulation or a mandatory standard refers to it, or when a producer declares conformity with it.

The document runs to 13 pages in English translation.

2 Scope Preview

SY/T 7454-2019 falls under ICS 75.020, in the field of petroleum and related technologies.

This catalogue holds 482 other SY/T standards in that field.

In this catalogue, SY/T standards carry edition years from 1973 to 2025.

3 About this standard

Sector: Oil & Gas Industry Standard (Recommended)

Issued by: National Energy Administration

English translation: about 13 pages (approximate)

Chinese original: about 19,117 characters

4 Related standards

Standards on related subjects:

SY/T 7774-2024 — Test method for sulfur isotope of source rock, oil, natural gas and water

GB/T 9711-2023 — Petroleum and natural gas industries - Steel pipe for pipeline transportation systems

SY/T 10025-2009 — Pre-operation inspection for offshore drilling unit

SY/T 6751-2024 — Technical specification for wireline logging and perforating under pressure operation

SY/T 6273-2024 — Explosive equipment for oil and gas wells

SY/T 5982-2024 — Analysis Method of Metal Elements in Oil and Gas Field Water

5 Classification and status

International classification (ICS): 75.020

Chinese Standard Classification (CCS): E 12

Prefix SY/T: recommended standard.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 13 pages — is available in the English PDF.

How to Download SY/T 7454-2019

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
13 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

SY/T 7454-2019

$345.00