Valid

SY/T 6905-2012Calibration method for liquid resistivity tools (English PDF)

液体电阻率仪校准方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (9 pages)

Need quotation for your management?

Get a formal quotation for SY/T 6905-2012 in 30 minutes.

Issued by

National Development and Reform Commission

Level / Type

National · Recommended

Issue date

January 1, 2012

Implementation date

January 1, 2012

Scope

SY/T 6905-2012 is the English-translated version of 液体电阻率仪校准方法.

SY/T 6905-2012 is the Chinese standard "Calibration method for liquid resistivity tools". This standard specifies the liquid resistivity meter calibration of the technical requirements, calibration equipment, calibration conditions, calibration method and recalibration interval.

It was issued by National Development and Reform Commission. It cites 1 other standard.

Found what you need?

Document preview — SY/T 6905-2012

National Standard of the People's Republic of China

ICS
75.180.99
Classification
E10

Issued by: National Development and Reform Commission

Contents

  • [Preview only]
  • 1 Scope
  • 1.2 Definition of terms
  • 2 Normative references
  • 2.1 General requirements
  • 2.2 Pressure-drop limitations and piping configurations
  • 2.3 Inlet stresses that originate from static loads in the discharge piping
  • 2.4 Inlet stresses that originate from discharge reaction forces
  • 2.5 Isolation valves in inlet piping
  • 2.6 Rupture disk devices in combination with pressure relief valves
  • 2.7 Process laterals connected to inlet piping of pressure relief valves
  • 2.8 Turbulence in pressure relief device inlets
  • 3 Terms and definitions
  • 3.2 Safe disposal of relieving fluids
  • 3.3 Back pressure limitations and sizing of pipe
  • 3.4 Considerations for pilot-operated pressure relief valves
  • 3.5 Stresses that originate from discharge piping
  • 3.6 Isolation valves in the discharge piping
  • 4 Isolation valves in pressure relief piping
  • 4.1 Determination of relief requirements
  • 4.2 Relieving pressure
  • 4.3 Sizing for gas or vapor relief
  • 4.4 Examples of isolation valve installations
  • 4.5 Sizing for liquid relief: relief valves requiring liquid capacity certification
  • 4.6 Sizing for liquid relief: relief valves not requiring liquid capacity certification
  • 4.7 Sizing for two-phase liquid/vapor relief
  • 4.8 Sizing for rupture disk devices
  • 5 Bonnet or pilot vent piping
  • 5.1 Conventional pressure relief valves
  • 5.2 Balanced bellows pressure relief valves
  • 5.3 Balanced piston pressure relief valve
  • 5.4 Pilot-operated pressure relief valves
  • 5.5 Thickness calculation of planar insulation layer
  • 6 Drain piping
  • 6.1 Installation conditions that require drain piping
  • 6.2 Safe practice for installation of drain piping
  • 6.3 SPM Location and Spatial Requirements
  • 6.4 Other materials
  • 6.5 Transportation, storage and custody of materials
  • 7 Pressure relief device location and position
  • 7.1 Inspection and maintenance
  • 7.2 Proximity to pressure source
  • 7.3 Proximity to other equipment
  • 7.4 Mounting position
  • 7.5 Test or lifting levers
  • 7.6 Heat tracing and insulation
  • 8 Bolting and gasketing
  • 8.1 Care in installation
  • 8.2 Proper gasketing and bolting for service requirements
  • 8.3 Welding
  • 8.4 Quality Control and Inspection
  • 9 Multiple pressure relief valves with staggered settings
  • 9.2 Installation of Mooring Foundation
  • 9.3 Laying of Mooring Lines
  • 9.4 Hook-up of Mooring Lines

1 Foreword

SY/T 6905-2012 is issued by National Development and Reform Commission.

The SY/T prefix marks a recommended standard. It is not law in itself: it becomes binding when a contract names it, when a regulation or a mandatory standard refers to it, or when a producer declares conformity with it.

The document runs to 9 pages in English translation.

2 Scope Preview

This standard specifies the liquid resistivity meter calibration of the technical requirements, calibration equipment, calibration conditions, calibration method and recalibration interval.

SY/T 6905-2012 falls under ICS 75.180.99, in the field of petroleum and related technologies.

This catalogue holds 482 other SY/T standards in that field.

In this catalogue, SY/T standards carry edition years from 1973 to 2025.

3 Normative references

The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document.

JJF 1059-1999

4 About this standard

Issued by: National Development and Reform Commission

English translation: about 9 pages (approximate)

5 Related standards

Standards on related subjects:

SY/T 6996-2014 — Assessment of Steel Oil and Gas Pipeline with Dent

SY/T 6151-2009 — Assessment of corroded steel pipelines

SY/T 10011-2006 — Guide to programing overall development program for oil fields

SY/T 6068-2024 — Maintenance specification for overhead sections of oil and gas pipelines and their ancillary facilities

SY/T 5922-2024 — Natural Gas Pipeline Operation Specifications

SY/T 6898-2012 — Experimental testing method of in-situ combustion parameters

6 Classification and status

International classification (ICS): 75.180.99

Chinese Standard Classification (CCS): E 10

Prefix SY/T: recommended standard.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 9 pages — is available in the English PDF.

Referenced standards

Normative references

JJF 1059-1999

How to Download SY/T 6905-2012

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
9 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

SY/T 6905-2012

$105.00