Valid

SY/T 6874-2012Recommended practice for planning, designing and constructing tension leg platform (English PDF)

张力腿平台规划、设计和建造的推荐做法

Preview PDF

This is a limited preview

Buy now to download the full PDF (113 pages)

Need quotation for your management?

Get a formal quotation for SY/T 6874-2012 in 30 minutes.

Issued by

National Development and Reform Commission

Level / Type

National · Recommended

Issue date

January 1, 2012

Implementation date

January 1, 2012

Scope

SY/T 6874-2012 is the English-translated version of 张力腿平台规划、设计和建造的推荐做法.

SY/T 6874-2012 is the Chinese standard "Recommended practice for planning, designing and constructing tension leg platform". This standard applies to tension leg platform design.

This standard focuses on the planning, design, construction and installation of all the different stages of the professional collaboration. Figure 2 shows the recommended design of the spiral. It was issued by National Development and Reform Commission.

Found what you need?

Document preview — SY/T 6874-2012

National Standard of the People's Republic of China

ICS
75.180.10
Classification
E94

Issued by: National Development and Reform Commission

Contents

  • [Preview only]
  • 1 Scope
  • 1.2 Definition of terms
  • 2 Normative references
  • 2.1 General requirements
  • 2.2 Pressure-drop limitations and piping configurations
  • 2.3 Inlet stresses that originate from static loads in the discharge piping
  • 2.4 Inlet stresses that originate from discharge reaction forces
  • 2.5 Isolation valves in inlet piping
  • 2.6 Rupture disk devices in combination with pressure relief valves
  • 2.7 Process laterals connected to inlet piping of pressure relief valves
  • 2.8 Turbulence in pressure relief device inlets
  • 3 Terms and definitions
  • 3.2 Safe disposal of relieving fluids
  • 3.3 Back pressure limitations and sizing of pipe
  • 3.4 Considerations for pilot-operated pressure relief valves
  • 3.5 Stresses that originate from discharge piping
  • 3.6 Isolation valves in the discharge piping
  • 4 Isolation valves in pressure relief piping
  • 4.1 Determination of relief requirements
  • 4.2 Relieving pressure
  • 4.3 Sizing for gas or vapor relief
  • 4.4 Examples of isolation valve installations
  • 4.5 Sizing for liquid relief: relief valves requiring liquid capacity certification
  • 4.6 Sizing for liquid relief: relief valves not requiring liquid capacity certification
  • 4.7 Sizing for two-phase liquid/vapor relief
  • 4.8 Sizing for rupture disk devices
  • 5 Bonnet or pilot vent piping
  • 5.1 Conventional pressure relief valves
  • 5.2 Balanced bellows pressure relief valves
  • 5.3 Balanced piston pressure relief valve
  • 5.4 Pilot-operated pressure relief valves
  • 5.5 Thickness calculation of planar insulation layer
  • 6 Drain piping
  • 6.1 Installation conditions that require drain piping
  • 6.2 Safe practice for installation of drain piping
  • 6.3 SPM Location and Spatial Requirements
  • 6.4 Other materials
  • 6.5 Transportation, storage and custody of materials
  • 7 Pressure relief device location and position
  • 7.1 Inspection and maintenance
  • 7.2 Proximity to pressure source
  • 7.3 Proximity to other equipment
  • 7.4 Mounting position
  • 7.5 Test or lifting levers
  • 7.6 Heat tracing and insulation
  • 8 Bolting and gasketing
  • 8.1 Care in installation
  • 8.2 Proper gasketing and bolting for service requirements
  • 8.3 Welding
  • 8.4 Quality Control and Inspection
  • 9 Multiple pressure relief valves with staggered settings
  • 9.2 Installation of Mooring Foundation
  • 9.3 Laying of Mooring Lines
  • 9.4 Hook-up of Mooring Lines

1 Foreword

SY/T 6874-2012 was issued by National Development and Reform Commission on 4 January 2012.

The SY/T prefix marks a recommended standard. It is not law in itself: it becomes binding when a contract names it, when a regulation or a mandatory standard refers to it, or when a producer declares conformity with it.

The document runs to 113 pages in English translation.

2 Scope Preview

This standard applies to tension leg platform design. This standard focuses on the planning, design, construction and installation of all the different stages of the professional collaboration. Figure 2 shows the recommended design of the spiral.

SY/T 6874-2012 falls under ICS 75.180.10, in the field of petroleum and related technologies.

This catalogue holds 482 other SY/T standards in that field.

In this catalogue, SY/T standards carry edition years from 1973 to 2025.

3 About this standard

Sector: Oil & Gas Industry Standard (Recommended)

Issued by: National Development and Reform Commission

English translation: about 113 pages (approximate)

Chinese original: about 169,153 characters

4 Related standards

Standards on related subjects:

GB/T 9109.5-2017 — Petroleum and liquid petroleum products dynamic measurement -- Part 5: Calculation of oil quantities

SY/T 5324-2013 — Pre-Stress Insulated Tubing

SY/T 6877-2012 — Buckling strength analysis of bars and frames, and spherical shells

SY/T 6876-2012 — Bulkling strength of shells

SY/T 6875-2012 — Buckling strength of plated structures

5 Classification and status

International classification (ICS): 75.180.10

Chinese Standard Classification (CCS): E 94

Prefix SY/T: recommended standard.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 113 pages — is available in the English PDF.

How to Download SY/T 6874-2012

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
113 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

SY/T 6874-2012

$2,345.00