SY/T 6861-2012Calibration method of drilling bit gauge (English PDF)
钻头规校准方法
This is a limited preview
Buy now to download the full PDF (9 pages)
Need quotation for your management?
Get a formal quotation for SY/T 6861-2012 in 30 minutes.
Issued by
National Development and Reform Commission
Level / Type
National · Recommended
Issue date
January 1, 2012
Implementation date
January 1, 2012
Scope
SY/T 6861-2012 is the English-translated version of 钻头规校准方法.
SY/T 6861-2012 is the Chinese standard "Calibration method of drilling bit gauge". This standard specifies the technical requirements of regulation drill, measurement characteristics, calibration conditions, calibration programs and methods, calibration results processing and recalibration interval. It was issued by National Development and Reform Commission.
Found what you need?
Document preview — SY/T 6861-2012
National Standard of the People's Republic of China
- ICS
- 75.180.10
- Classification
- E92
Issued by: National Development and Reform Commission
Contents
- [Preview only]
- 1 Scope
- 1.2 Definition of terms
- 2 Normative references
- 2.1 General requirements
- 2.2 Pressure-drop limitations and piping configurations
- 2.3 Inlet stresses that originate from static loads in the discharge piping
- 2.4 Inlet stresses that originate from discharge reaction forces
- 2.5 Isolation valves in inlet piping
- 2.6 Rupture disk devices in combination with pressure relief valves
- 2.7 Process laterals connected to inlet piping of pressure relief valves
- 2.8 Turbulence in pressure relief device inlets
- 3 Terms and definitions
- 3.2 Safe disposal of relieving fluids
- 3.3 Back pressure limitations and sizing of pipe
- 3.4 Considerations for pilot-operated pressure relief valves
- 3.5 Stresses that originate from discharge piping
- 3.6 Isolation valves in the discharge piping
- 4 Isolation valves in pressure relief piping
- 4.1 Determination of relief requirements
- 4.2 Relieving pressure
- 4.3 Sizing for gas or vapor relief
- 4.4 Examples of isolation valve installations
- 4.5 Sizing for liquid relief: relief valves requiring liquid capacity certification
- 4.6 Sizing for liquid relief: relief valves not requiring liquid capacity certification
- 4.7 Sizing for two-phase liquid/vapor relief
- 4.8 Sizing for rupture disk devices
- 5 Bonnet or pilot vent piping
- 5.1 Conventional pressure relief valves
- 5.2 Balanced bellows pressure relief valves
- 5.3 Balanced piston pressure relief valve
- 5.4 Pilot-operated pressure relief valves
- 5.5 Thickness calculation of planar insulation layer
- 6 Drain piping
- 6.1 Installation conditions that require drain piping
- 6.2 Safe practice for installation of drain piping
- 6.3 SPM Location and Spatial Requirements
- 6.4 Other materials
- 6.5 Transportation, storage and custody of materials
- 7 Pressure relief device location and position
- 7.1 Inspection and maintenance
- 7.2 Proximity to pressure source
- 7.3 Proximity to other equipment
- 7.4 Mounting position
- 7.5 Test or lifting levers
- 7.6 Heat tracing and insulation
- 8 Bolting and gasketing
- 8.1 Care in installation
- 8.2 Proper gasketing and bolting for service requirements
- 8.3 Welding
- 8.4 Quality Control and Inspection
- 9 Multiple pressure relief valves with staggered settings
- 9.2 Installation of Mooring Foundation
- 9.3 Laying of Mooring Lines
- 9.4 Hook-up of Mooring Lines
1 Foreword
SY/T 6861-2012 was issued by National Development and Reform Commission on 4 January 2012.
The SY/T prefix marks a recommended standard. It is not law in itself: it becomes binding when a contract names it, when a regulation or a mandatory standard refers to it, or when a producer declares conformity with it.
The document runs to 9 pages in English translation.
2 Scope Preview
This standard specifies the technical requirements of regulation drill, measurement characteristics, calibration conditions, calibration programs and methods, calibration results processing and recalibration interval.
SY/T 6861-2012 falls under ICS 75.180.10, in the field of petroleum and related technologies.
This catalogue holds 482 other SY/T standards in that field.
In this catalogue, SY/T standards carry edition years from 1973 to 2025.
3 About this standard
Sector: Oil & Gas Industry Standard (Recommended)
Issued by: National Development and Reform Commission
English translation: about 9 pages (approximate)
Chinese original: about 13,158 characters
4 Related standards
Standards on related subjects:
SY/T 5324-2013 — Pre-Stress Insulated Tubing
SY 0007-1999 — Design standard of corrosion control for steel pipeline and storage tank
SY/T 6857.1-2024 — Oil well pipes for special environments in the petroleum and natural gas industry Part 1: Oil and gas field environments containing H2S - Recommended practices for the selection of carbon steel and low alloy steel oil pipes and casings
SY/T 6868-2023 — Oil and gas drilling equipment Well control system
5 Classification and status
International classification (ICS): 75.180.10
Chinese Standard Classification (CCS): E 92
Prefix SY/T: recommended standard.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 9 pages — is available in the English PDF.
How to Download SY/T 6861-2012
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
SY/T 0021-2025 — Code for Building Design of Oil and Gas Engineering Projects
SY/T 0031-2025 — Safety Regulations for Heating Furnaces Used in the Petroleum Industry
SY/T 0048-2025 — General Layout Design Specifications for Oil and Gas Engineering Projects
SY/T 6861-2012
$135.00