Valid

SY/T 0439-2012Fundamental terminology of oil and gas engineering (English PDF)

石油天然气工程建设基本术语

Preview PDF

This is a limited preview

Buy now to download the full PDF (155 pages)

Need quotation for your management?

Get a formal quotation for SY/T 0439-2012 in 30 minutes.

Issued by

National Development and Reform Commission

Level / Type

National · Recommended

Issue date

January 1, 2012

Implementation date

January 1, 2012

Scope

SY/T 0439-2012 is the English-translated version of 石油天然气工程建设基本术语.

SY/T 0439-2012 is the Chinese standard "Fundamental terminology of oil and gas engineering". This standard applies to oil, gas, oil pipelines, gas pipelines, oil depots, gas storage, liquefied natural gas and other engineering design. It was issued by National Development and Reform Commission.

Found what you need?

Document preview — SY/T 0439-2012

National Standard of the People's Republic of China

ICS
75.010
Classification
P71

Issued by: National Development and Reform Commission

Contents

  • [Preview only]
  • 1 Scope
  • 1.2 Definition of terms
  • 2 Normative references
  • 2.1 General requirements
  • 2.2 Pressure-drop limitations and piping configurations
  • 2.3 Inlet stresses that originate from static loads in the discharge piping
  • 2.4 Inlet stresses that originate from discharge reaction forces
  • 2.5 Isolation valves in inlet piping
  • 2.6 Rupture disk devices in combination with pressure relief valves
  • 2.7 Process laterals connected to inlet piping of pressure relief valves
  • 2.8 Turbulence in pressure relief device inlets
  • 3 Terms and definitions
  • 3.2 Safe disposal of relieving fluids
  • 3.3 Back pressure limitations and sizing of pipe
  • 3.4 Considerations for pilot-operated pressure relief valves
  • 3.5 Stresses that originate from discharge piping
  • 3.6 Isolation valves in the discharge piping
  • 4 Isolation valves in pressure relief piping
  • 4.1 Determination of relief requirements
  • 4.2 Relieving pressure
  • 4.3 Sizing for gas or vapor relief
  • 4.4 Examples of isolation valve installations
  • 4.5 Sizing for liquid relief: relief valves requiring liquid capacity certification
  • 4.6 Sizing for liquid relief: relief valves not requiring liquid capacity certification
  • 4.7 Sizing for two-phase liquid/vapor relief
  • 4.8 Sizing for rupture disk devices
  • 5 Bonnet or pilot vent piping
  • 5.1 Conventional pressure relief valves
  • 5.2 Balanced bellows pressure relief valves
  • 5.3 Balanced piston pressure relief valve
  • 5.4 Pilot-operated pressure relief valves
  • 5.5 Thickness calculation of planar insulation layer
  • 6 Drain piping
  • 6.1 Installation conditions that require drain piping
  • 6.2 Safe practice for installation of drain piping
  • 6.3 SPM Location and Spatial Requirements
  • 6.4 Other materials
  • 6.5 Transportation, storage and custody of materials
  • 7 Pressure relief device location and position
  • 7.1 Inspection and maintenance
  • 7.2 Proximity to pressure source
  • 7.3 Proximity to other equipment
  • 7.4 Mounting position
  • 7.5 Test or lifting levers
  • 7.6 Heat tracing and insulation
  • 8 Bolting and gasketing
  • 8.1 Care in installation
  • 8.2 Proper gasketing and bolting for service requirements
  • 8.3 Welding
  • 8.4 Quality Control and Inspection
  • 9 Multiple pressure relief valves with staggered settings
  • 9.2 Installation of Mooring Foundation
  • 9.3 Laying of Mooring Lines
  • 9.4 Hook-up of Mooring Lines

1 Foreword

SY/T 0439-2012 is issued by National Development and Reform Commission.

The SY/T prefix marks a recommended standard. It is not law in itself: it becomes binding when a contract names it, when a regulation or a mandatory standard refers to it, or when a producer declares conformity with it.

The document runs to 155 pages in English translation.

2 Scope Preview

This standard applies to oil, gas, oil pipelines, gas pipelines, oil depots, gas storage, liquefied natural gas and other engineering design.

SY/T 0439-2012 falls under ICS 75.010, in the field of petroleum and related technologies.

This catalogue holds 482 other SY/T standards in that field.

In this catalogue, SY/T standards carry edition years from 1973 to 2025.

3 About this standard

Sector: Oil & Gas Industry Standard (Recommended)

Issued by: National Development and Reform Commission

English translation: about 155 pages (approximate)

Chinese original: about 233,228 characters

4 Related standards

Standards on related subjects:

SH/T 3164-2021 — Design specification for instrument system lightning surge protection in petrochemical industry

MT/T 593.5-2011 — Artificial frozen soil physics mechanics performance test. Part 5: Artificial frozen soil tri-axial shear test method

SY/T 0329-2017 — Code for inspection of large oil tanks foundation

SY/T 0612-2014 — Code for design of gathering and transmission systems in highly hydrogen sulfide gas field

SY/T 0447-2014 — Standard of coal tar epoxy coating for buried steel pipeline

5 Classification and status

International classification (ICS): 75.010

Chinese Standard Classification (CCS): P 71

Prefix SY/T: recommended standard.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 155 pages — is available in the English PDF.

How to Download SY/T 0439-2012

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
155 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

SY/T 0439-2012

$2,900.00