SN/T 3809-2014Determination of potassium content in potassium chloride and potassium sulphate - X-ray fluorescence spectrometry (English PDF)
氯化钾和硫酸钾中钾含量测定 X射线荧光光谱法
This is a limited preview
Buy now to download the full PDF (8 pages)
Need quotation for your management?
Get a formal quotation for SN/T 3809-2014 in 30 minutes.
Issued by
General Administration of Customs
Level / Type
National · Recommended
Issue date
January 13, 2014
Implementation date
August 1, 2014
Scope
SN/T 3809-2014 is the English-translated version of 氯化钾和硫酸钾中钾含量测定 X射线荧光光谱法.
SN/T 3809-2014 - This standard specifies the method for determination of potassium chloride and potassium sulfate potassium (K2O) content using wavelength dispersive X-ray fluorescence spectrometer.
This standard applies to potassium chloride and potassium sulfate potassium (K2O) content determination. Measurement range (mass fraction) are shown in Table 1.
Table 1 measurement range potassium chloride and potassium sulfate potassium content Sample type Measurement range (mass fraction) /% Potassium chloride 53.07 ~ 63.18 Potassium 38.61 ~ 54.05
Found what you need?
Document preview — SN/T 3809-2014
National Standard of the People's Republic of China
- ICS
- 71.040.30
- Classification
- G12
Issued by: General Administration of Customs
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Method Summary
- 4 Reagents
Foreword
This standard was drafted in accordance with GB/T 1.1-2009 given rules.
This standard is proposed and managed by the National Certification and Accreditation Administration Committee.
This standard was drafted. People's Republic of China Manzhouli Exit Inspection and Quarantine.
1 Scope
This standard specifies the method for determination of potassium chloride and potassium sulfate potassium (K2O) content using wavelength dispersive X-ray fluorescence spectrometer.
This standard applies to potassium chloride and potassium sulfate potassium (K2O) content determination. Measurement range (mass fraction) are shown in Table 1.
Table 1 measurement range potassium chloride and potassium sulfate potassium content
Sample type Measurement range (mass fraction) /% Potassium chloride 53.07 ~ 63.18 Potassium 38.61 ~ 54.05
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document.
JJG810 wavelength dispersive X-ray fluorescence spectrometer
3 Method Summary
The samples were prepared as borate glass melt samples. Samples measuring element and the effect of potassium is characterized by X-ray fluorescence spectrum Strength, calculated based on the calibration curve K (of K2O) content.
4 Reagents
Unless otherwise indicated in the analysis using only recognized as analytical reagents.
4.1 lithium tetraborate and lithium metaborate mixed flux (67.33), X-ray fluorescence dedicated reagent. Before use at 650 °C burning 4h, then in the drier cooled storage.
4.2 bromide.
4.3 potassium chloride, high purity reagents or standard material. Burning 6h at 500 °C, then cooled in a desiccator.
4.4 potassium, high purity reagents or standard material. Baking at 130 °C 2h, then cooled in a desiccator.
4.5 Sodium chloride, baked at 105 °C 2h, then cooled in a desiccator.
4.6 sodium sulfate, drying at 105 °C 2h, then cooled in a desiccator.
4.7 anhydrous calcium sulfate, at 500 °C burning 2h, cooled in a desiccator.
4.8 magnesia, calcined at 1000 °C 1h, then placed in a desiccator, weighed immediately after cooling.
4.9 saturated solution of lithium bromide. The lithium bromide (4.2) dissolved in water to saturation, and filtered.
4.10 mixture A. Take 7g sodium chloride (4.5), 2g of anhydrous calcium sulfate (4.7) and 1g of magnesium oxide (4.8), grinding mix, stored in a desiccator.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 8 pages — is available in the English PDF.
Referenced standards
Normative references
JJG810
How to Download SN/T 3809-2014
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
SN/T 2378.1-2026 — Rules for the inspection of imported natural gas - Part 1: Pipeline inspection
SN/T 5778-2026 — Rules for the inspection of common imported and exported rare earth products
SN/T 5784-2026 — Inspection of casting and forging production processes of steel - Hot acid etching method
SN/T 3809-2014
$249.00